Oiling System for BMW 3 Series F34 (2014+)

Clear BMW chassis

Please ensure your correct model is selected

Tasked with keeping everything properly lubricated, the oiling system is one of the most if not THE most fundamental parts of the engine. Make sure that everything is in good working order and flowing properly to ensure your engine has a long and trouble-free service life.

Sub-Categories

Sort By:

MMX Performance - Corporate Logo
T#:22723756
Part#: MMR03-0504
Ships in 2 Business Days
$ 37.99 USD
Free Shipping on orders $49 and up
$ 37.99 USD
Free Shipping on orders $49 and up
Mishimoto - Corporate Logo
T#:597051
Part#: MMOCCLA
In Stock
$ 127.99 USD
Free Shipping
$ 127.99 USD
Free Shipping
WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less
MMX Oil Filler Cap - Black
For Most BMW Models 2007 Onwards or Mini Models
MMX Performance - Corporate Logo
T#:4552062
Part#: MMR03-0102-BL
Ships in 1 Business Day
$ 127.99 USD
$ 127.99 USD
MMX's Performance billet oil filler cap machined from billet T-6061 aluminum has been designed to instantly give your engine bay an subtle aesthetic upgrade. This cap comes in a Black finish. *Note: After exposure to excessive heat over prolonged periods, overall finish fading can occur. Reusing of original seal is required.
Show More Show Less

MMX Performance - Corporate Logo
T#:4565826
Part#: MMR17-0101
Back Ordered
$ 70.99 USD
Free Shipping on orders $49 and up
MMR's Low Temp Oil Thermostat is one of the easiest ways to increase your oil cooling capability. Rated to maintain the oil temps at about 194F (90c) to 230F (110c). Machined from aircraft grade T-6061 aluminum and anodized in MMR's trademark finish for durability. Installation is easy as it fits right into the OEM oil thermostat housing on the N54 and N55. Highly recommended for cars used on the track or with a higher power and torque output than stock.
Show More Show Less

Mishimoto - Corporate Logo
T#:372557
Part#: MMOCCCF
In Stock
$ 162.99 USD
Free Shipping
$ 162.99 USD
Free Shipping
Universal kit with a catch can and rubber hose; for retrofitting on a variety of vehicles. Carbon fiber catch can prevents a harmful buildup of oil inside of the turbocharger, intake manifold, intercooler and piping. Separates oil particles from PCV/CCV air Defends intercooler, intake system, and essential components from oil blow-by Made from lightweight carbon fiber Compact design makes for easy engine bay placement Checking fluid levels made easy with built in sight tube Comes complete with mounting bracket, hose, all necessary clamps, fittings, and mounting hardware Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less
MMX Performance - Corporate Logo
T#:4552065
Part#: MMR03-0101-BL
Ships in 2 Business Days
$ 142.99 USD
Free Shipping
$ 142.99 USD
Free Shipping
If you are looking for peace of mind over the prone to cracking OEM plastic housing cap, this oil filter housing cap by MMX may be exactly what you are looking for. Composed of billet aluminum, this cap is light, durable, and dresses up your engine bay! Comes finished with a polished anodized dark anthracite coating. Installation is simple as it can be replaced while completing an oil change. *Note: After exposure to excessive heat over prolonged periods, overall finish fading can occur.
Show More Show Less

Mishimoto - Corporate Logo
T#:23020165
Part#: MMBCC-CBTWO
In Stock
$ 160.99 USD
Free Shipping on orders $49 and up

Optimize your vehicle's performance and shield crucial components with the Mishimoto Compact 2-Port Baffled Oil Catch Can. This innovative solution effectively separates oil particles from PCV/CCV air using a 50-micron bronze filter, ensuring defense against oil blow-by for your intercooler, intake system, and vital parts. Constructed with a patented billet 6061 aluminum can sealed with Viton™ O-Rings, this catch can guarantees both durability and effectiveness.

Equipped with a universal mounting bracket, it allows adaptable installation and comes complete with two CNC-machined aluminum 1/2" barbed hose fittings. With an enhanced 3 oz internal capacity, service intervals are prolonged, while its fully serviceable filter and can ensure enduring functionality.

Engineered for safety in pressurized applications, the internal air diverter enhances oil separation by amplifying air turbulence. Available in black, red, or polished finishes, this catch can preserves proper octane levels, reducing potential detonation and promoting extended engine life.

The product package includes the Compact 2-Port Baffled Oil Catch Can, two Aluminum 1/2" Barbed Fittings, and a Universal Mounting Bracket, all backed by the Mishimoto Lifetime Warranty.

WARNING! Prop 65 may apply to this product.

Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to all companies selling products in California.

Prop 65 mandates listing any chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm.

For more information about California Prop 65 warning, visit: www.P65Warnings.ca.gov.

Show More Show Less
Mishimoto Universal 10 Row Oil Cooler
For custom applications only. Not a direct bolt on.
Mishimoto - Corporate Logo
T#:378421
Part#: MMOCU
In Stock
$ 410.99 USD
Free Shipping
$ 410.99 USD
Free Shipping
This universal oil cooler from Mishimoto is far superior to the factory unit with its 11" x 2.76" x 1.97" core. Even under optimum driving conditions increased oil temperatures will cause a drop in pressure and will decrease the ability for your engine to be properly lubricated. With this new oil cooler, you can keep your oil temperatures down for optimum driving conditions. The kit includes 4 feet of stainless braided line, adapter fittings, and oil filter sandwich adapter. Mishimoto Automotive is a leading manufacturer of aftermarket performance cooling products. The company was established back in 2003 with one goal. That goal was to provide customers with quality cooling system upgrades that work on the track and on the road. At Mishimoto, you never have to worry about the quality of the product you are installing. This kit is universal and is not a direct bolt on. *For custom applications only. Not a direct bolt on. WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less

Mishimoto 19 Row Universal Oil Cooler
For custom applications only. Not a direct bolt on.
Mishimoto - Corporate Logo
T#:378414
Part#: MMOCUL
In Stock at Vendor
$ 536.99 USD
Free Shipping
$ 536.99 USD
Free Shipping
Even under optimum driving conditions increased oil temperatures will cause a drop in pressure and will decrease the ability for your engine to be properly lubricated. With this new oil cooler, you can keep your oil temperatures down for optimum driving conditions. The kit includes four-feet of stainless braided line, adapter fittings, and oil filter sandwich adapter. Rows: 19 Overall Dimensions: 13" x 5.5" x 2" Core Dimensions: 11.25" x 5.5" x 2" Braided Hoses: 4ft .75 inch & 4ft 9 inch Braided Hose Fittings: -10AN Sandwich Plate Fittings: -10AN WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less

Mishimoto - Corporate Logo
T#:389788
Part#: MMBCCN20N2612CB
In Stock at Vendor
$ 278.95 USD
Free Shipping
$ 278.95 USD
Free Shipping
il venting and circulation continues to be a problem on BMW engines and the N20 engine is not immune from this. The existing stock system does a poor job of separating fluid and vapor and this leads to an oily film or even small pools of oil throughout the turbos and intake. Performance issues are caused by oil sneaking by the ring seals and is coating the intake piping, intercooler, intake valves, and other critical areas. The problem is worsened with higher boost levels. Oil is excellent for lubricating moving parts but terrible when it gets into the combustion chamber, effectively lowering the octane rating and reducing performance. Our own shop has gone the extra step and offers media and chemical blasting of the intake valves to strip away the oily buildup we have seen. Our shop also strongly recommends an oil catch can be installed in the line for the crankcase vent. The oil catch can traps oil as it leaves the valve cover and holds it in a canister. This catch can is located on the cooler side of the engine where the oil will condense easier and stay in the can. Whatever minimal vapors are left over in the oil is then vented back through the canister and into the intake where it is safe to be burned up in the engine or recirculated back through the system again. This is the way the system was designed! At each oil change simply unscrew the canister and empty the trapped oil with your regular used oil. Installing one of these will avoid costly repairs in the future and help maintain your boost and performance. It's one of the smartest modifications you can make because it demonstrates a well-thought out tuning strategy and care for the condition of your engine. The Mishimoto Oil Catch Can is made from aluminum and with a stealthy black anodized finish. It installs on the cooler side of the engine with a dedicated bracket and new oversized vent lines. The location is key as heat will evaporate the oil and send too much vapor back into the engine (where cooler air will turn it back into fluid). Note: Since the crankcase vent system is considered part of the overall emissions system, installing this may be a violation of local, state, and federal laws. While exemptions are made for track/race and off-road use, check with your local state inspection facility on using this in street-driven vehicles. This item fits the following BMWs with the N20 or N26 turbo engine: 2014-2016 F2X 228i 228i xDrive 2012-2016 F3X 320i 320i xDrive 328i 328i xDrive 428i 428i xDrive WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less
MMX Performance - Corporate Logo
T#:4552049
Part#: MMR03-0502-KP
Special Order: No Guaranteed ETA
$ 21.99 USD
Free Shipping on orders $49 and up
The MMX Performance billet adaptor is a helpful addition for those wishing to run an auxiliary oil pressure or oil temperature gauge. The adaptor replaces the plug that can be found on the oil cooler thermostat assembly with a 1/8NPT gauge adaptor.
Show More Show Less
MMX Performance - Corporate Logo
T#:5269482
Part#: MMR03-0502BL
Special Order: No Guaranteed ETA
$ 136.99 USD
Free Shipping
$ 136.99 USD
Free Shipping
This dress-up kit offers a high-quality aesthetic update to the OE thermostat cover. Thermostat dress up kit for the BMW N55, N54, and S55 engines manufactured from T6061 billet aluminum. Installation is extremely easy and dresses up the engine bay nicely. *Note: After exposure to excessive heat over prolonged periods, overall finish fading can occur.
Show More Show Less


MMX Performance - Corporate Logo
T#:29035359
Part#: MMR17-1502
Special Order: No Guaranteed ETA
$ 81.99 USD
Free Shipping on orders $49 and up
Get rid of the notorious B58 oil filter disintegration problem forevermore with the MMR Performance Oil Filter. By replacing the factory paper filter element with MMR’s advanced high-flow, high-filtration stainless steel filter unit, you will protect your engine from the big bills (and potentially worse) caused by the OE filter’s collapse failure. The oil filters on BMW’s B58 & B57 3.0 6-cylinder engines (both petrol and diesel) suffer from a well-documented quality problem with the factory paper-element oil filter. At service time, when removal of the filter is attempted, the bottom section frequently breaks away from the disintegrated filtration material. This leaves the broken base stuck in the oil filter housing and an expensive removal/replacement job to extract the remains and fit a new housing. Such is the problem that there’s even an official BMW technical bulletin to warn their dealers of this. The MMR replacement Oil Filter is a pretty special replacement filter. It fixes this annoying problem once and for all. The MMR Oil Filter element is made from a pleated high-flow stainless steel micronic filter cloth – a medical-grade material guaranteed to filter out oil contamination right down to 20 Microns, ensuring far better protection than paper-based filters can achieve. As well as this exceptional filtration, the filter material allows for five times the flow of comparable paper oil filters. Its design provides consistent filtering across entire filter surface. The failure of the factory oil filter generally just leads to a large bill to extract the damaged remnants. However, more worryingly, it has occasionally been known to lead to broken pieces of filter media running through the small oilways and orifices of the engine’s lubrication system, risking blocking the oil running round the bearings and VANOS system and causing much greater mechanical damage before it is caught. The MMR Oil Filter is a reusable unit which can be used over and over again. As long as it is thoroughly cleaned at each oil change, it will last the lifetime of the vehicle and keep on protecting the engine just as it did when new. However, proper cleaning is not necessarily a DIY job, as it requires the use of a suitable solvent to break down the old oil, and cleaning from the inside out with compressed air to remove any risk of debris remaining. If you have any doubts about this, we recommend as best-practice to change filter with every oil-change. The MMR Oil Filter is a lifetime reusable filter. But to resuse and avoid any future loss of filtration or oil flow, it is essential that it is thoroughly cleaned at each oil change as follows: Remove MMR Oil Filter from filter housing Remove 3x O-Rings from MMR Oil Filter prior to Step 3, as fuel will degrade and cause damage to these rubber/Viton components. Soak the filter one of the following fluids for 5-10 minutes – Petrol/Gasoline or Carb Cleaner or Soap and Water Agitate/stir every few minutes until the outer surface is free of any engine debris Dry the filter using compressed air, blow air through the filter, (do not press the compressed air gun against the filter, keep at least a 10mm gap from nozzle to filter) starting from the inside out, then at an angle on the outside of the screen to further remove any remaining particles or cleaning solution. Once dry, reinstall O-Rings (MMR advices replacement of these O-Rings every oil service - See ES4810064) and refit into oil filter housing and engine. If you have any doubt about your ability to perform this sequence, we recommend replacing the filter element with each oil change.
Show More Show Less
Mishimoto - Corporate Logo
T#:51075066
Part#: MMBCC-N20N26-12C
Ships in 3 Business Days
New Item
$ 278.99 USD
Free Shipping on orders $49 and up
This Mishimoto Catch Can offers a robust alternative to standard air-oil separators.
MMX Performance - Corporate Logo
T#:48608191
Part#: MMR03-0004
Ships in 5 Business Days
$ 40.00 USD
Free Shipping
$ 40.00 USD
Free Shipping
The MMX Billet Air Conditioning Cap Set replaces cheap OEM pieces with durable aluminum replacements that withstand track thermal cycles and everyday driving.

MMX Performance - Corporate Logo
T#:29035360
Part#: MMR17-0000
Special Order: No Guaranteed ETA
$ 13.99 USD
Free Shipping on orders $49 and up
Genuine MMR Performance O-Ring service kit for the MMX Performance oil filter and billet housing. Does not include MMR oil filter or billet housing, only the four O-Rings needed to service our reusable filter. The MMR Performance oil filter and housing contains four O-Rings within the kit. We recommend you replace the O-Ring set on a regular basis when changing or cleaning the MMR filter, in order to maintain the integrity of the sealing properties it was designed to provide. As it's a direct replacement with the original O-Ring set supplied, it's a very straightforward process to swap and replace. Fitment is limited to the MMR Performance oil filter (MMR17-1502 - See ES4810063) to protect against the notorious B58 oil filter collapse
Show More Show Less

MMX Performance - Corporate Logo
T#:5269476
Part#: MMR03-0502KBL
Special Order: No Guaranteed ETA
$ 25.99 USD
Free Shipping on orders $49 and up
The MMX Performance billet adaptor is a helpful addition for those wishing to run an auxiliary oil pressure or oil temperature gauge. The adaptor replaces the plug that can be found on the oil cooler thermostat assembly with a 1/8NPT gauge adaptor.
Show More Show Less
MMX Performance - Corporate Logo
T#:5269479
Part#: MMR03-0502GBL
Special Order: No Guaranteed ETA
$ 111.99 USD
Free Shipping on orders $49 and up
This dress-up kit offers a high-quality aesthetic update to the OE thermostat cover. Thermostat dress up kit for the BMW N55, N54, and S55 engines manufactured from T6061 billet aluminum. Installation is extremely easy and dresses up the engine bay nicely. Includes billet adaptor which is a helpful addition for those wishing to run an auxiliary oil pressure or oil temperature gauge. The adaptor replaces the plug that can be found on the oil cooler thermostat assembly with a 1/8NPT gauge adaptor. *Note: After exposure to excessive heat over prolonged periods, overall finish fading can occur.
Show More Show Less

MMX Performance - Corporate Logo
T#:28968889
Part#: MMR03-1601
Special Order: No Guaranteed ETA
$ 127.99 USD
Free Shipping on orders $49 and up