BMW Maintenance & Tune-Up Parts for BMW F82 M4 S55 3.0L

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve 

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
 ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

For BMW M54 applications, coil styles vary between M or N depending on the vehicle's production date. Models produced up to September 2002 require the M series style coil, while those manufactured after September 2002 use N series style coils. It's crucial to visually compare and verify the correct coil needed for your vehicle before making a purchase.

Benefits:

• Specific coil styles for different BMW M54 application dates
• Helps ensure the right replacement part for your vehicle's coil
• Visual verification recommended prior to purchase for compatibility

BMW’s Getrag GS7D36SG Dual-Clutch Transmission is a masterpiece of engineering. It's renowned for its rapid gear changes, robust construction, and direct, motorsport-inspired feel. While the transmission itself delivers exceptional performance, its supporting components don’t always keep pace. The factory plastic oil pan and limited oil capacity compromise cooling efficiency and long-term reliability, especially during high-performance use. With this in mind, we set out to engineer a solution that elevates durability, thermal management, and fluid control to match the transmission’s world-class performance.

We've designed a permanent, high-performance replacement for the flawed OEM pan: a cast-aluminum, increased-capacity upgrade that enhances cooling and durability. Its all-aluminum construction provides a significant upgrade over the OE plastic pan, which is prone to cracking when impacted by road debris. Engineered for those who demand more from their vehicle, our design increases fluid capacity to promote superior cooling and help maintain optimal transmission temperatures, even in the most demanding conditions.

To ensure a leak-free seal, we engineered a heavy-duty Viton gasket specific to their transmission pan design. The Viton material provides exceptional reliability under high temperatures and resists deformation—a common failure point of the factory rubber gasket. For further protection, integrated magnets actively attract and hold metal debris that could otherwise compromise the transmission's longevity. This innovative design keeps your fluid clean and extends the overall life of your drivetrain.

Whether your DCT-equipped BMW serves as a track car or a highway cruiser, this pan ensures your transmission remains cool and efficient, minimizing the risk of overheating and wear.

DESIGN

Durable cast aluminum construction High-capacity design increases fluid volume (~7.5L capacity) Specifically designed to accept the OEM suction filter (28107842828) Hard coat black anodized with raw "Turner" logo KEY BENEFITS

A resilient, reliable replacement for the OE plastic fluid pan—crafted from aluminum for superior durability and features a threaded drain plug to prevent stripped threads Increased fluid capacity and cooling fins work together to provide a drastic increase in cooling Compatibility with the OEM suction filter ensures an easy service KIT CONTENTS

High-Capacity Aluminum Transmission Pan Perimeter Gasket/O-Ring Mounting Screws (14) Drain Plug PRODUCT DEVELOPMENT

Our High-Capacity DCT Transmission Pan was designed, engineered, tested, and quality inspected by our Research and Development team in our Wadsworth, Ohio, facility. We strive for the highest level of precision and quality through leading-edge product development technology, including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer, and rigorous long-term product testing.

Bring your aFe filter back to life with a Restore kit from aFe. Included is filter cleaner & replacement oil. These air filter oils is designed to not harm MAF sensors, while allowing the filter to catch as much debris as possible.

Used for Pro 5 R filters

Featuring silver fine wire center electrode - Superior ignition ability increases engine power!

Although these come pre-gapped we highly recommend double checking the plug gap upon receiving them and adjusting to your vehicle's individual needs.
For the N55/S55, these plugs are 2 Steps Colder, while for the N54 they are 3 Steps Colder.

Note that BMW Spark plugs require a special 12 point 14mm thin walled socket. We have several options available in our catalog that will help you get your spark plugs changed. The BMW part number for the tool is 83300495560, but we recommend the Schwaben brand T#373727 that won't cost you an arm and a leg.

Brisk Silver Racing Spark Plugs are the best solution for high performance and racing engines. Silver Spark Plugs provide many unique and beneficial characteristics, Silver is taking spark plug technology to a whole new level, here are many reasons why our Brisk Silver Racing Spark Plugs are beneficial for your engines performance. Silver is the best conductor of any metal! It conducts 560% more electricity & 481% more heat than Platinum, and 276% more electricity & 177% more heat than Iridium.

Silver spark plug electrodes transfer electricity & heat better than any other spark plug material resulting in the most powerful spark! This is beneficial for a full complete combustion of the available fuel and air in the combustion chamber, combustion efficiency creates horsepower gains.

Key Benefits and Applications of Brisk Silver Racing Spark Plugs:

Silver is the best Electric and Heat Conductor - the best material for performance and racing spark plugs
Superior Ignition Ability Increases Engine Power Lower Required Supplied Ignition Voltage
Good Resistance to Fouling and Easier Starts
Race Engines and Engines with Hard to Ignite Fuels
Supercharged / Turbocharged / Nitrous engines
Excellent for Total Loss Ignition Systems
Excellent Spark Plug Choice for any Vehicle, Stock or Modified, even for High Mileage Vehicles and Vehicles With Oil Consumption Problems
Spark Plug Specs:

12mm thread
1.05"(26.1mm) reach
14mm Bi-Hex
gasket seat
non-projection tip
resistor
Silver center el.
cut-back ground electrode
* Replacement for NGK SILZKBR9F8S (BMW# 12120042724)
* One heat range colder than NGK 97506 SILZKBR8D8S

When it comes time to change your spark plugs, you may wonder about colder stepped spark plugs as many others have. Colder spark plugs work by pulling more heat out of the engine's cylinders (making them "colder") and dissipating it into the engine's head, which is then cooled by the cooling system. Depending on how you have your engine built, these could be a great addition! Colder plugs can help prevent engine knock and prevent the tip of the spark plug from melting or misfiring.

There are two rules that most people tend to go by when deciding on which spark plugs to buy:

The first rule of thumb is that with every 100 horsepower added, you should run spark plugs that are a step colder than your stock plugs. This is generally accepted across the motorsports community but unfortunately isn't always the most accurate measurement of when you will need colder plugs.
The second rule is to go a step colder any time you massively alter cylinder temperatures by adding forced induction to an NA engine, by increasing compression ratio, after altering timing in a major way, or by changing fuel types to something with a higher octane rating such as racing fuel.
Adding spark plugs that are a step colder outside of these conditions, with no real change to the engine, can actually hurt more than help by leading to spark plugs fouling quicker than normal and by making the car harder to start in cold weather conditions.

BMW’s Getrag GS7D36SG Dual-Clutch Transmission is a masterpiece of engineering. It's renowned for its rapid gear changes, robust construction, and direct, motorsport-inspired feel. While the transmission itself delivers exceptional performance, its supporting components don’t always keep pace. The factory plastic oil pan and limited oil capacity compromise cooling efficiency and long-term reliability, especially during high-performance use. With this in mind, we set out to engineer a solution that elevates durability, thermal management, and fluid control to match the transmission’s world-class performance.

We've designed a permanent, high-performance replacement for the flawed OEM pan: a cast-aluminum, increased-capacity upgrade that enhances cooling and durability. Its all-aluminum construction provides a significant upgrade over the OE plastic pan, which is prone to cracking when impacted by road debris. Engineered for those who demand more from their vehicle, our design increases fluid capacity to promote superior cooling and help maintain optimal transmission temperatures, even in the most demanding conditions.

To ensure a leak-free seal, we engineered a heavy-duty Viton gasket specific to their transmission pan design. The Viton material provides exceptional reliability under high temperatures and resists deformation—a common failure point of the factory rubber gasket. For further protection, integrated magnets actively attract and hold metal debris that could otherwise compromise the transmission's longevity. This innovative design keeps your fluid clean and extends the overall life of your drivetrain.

Whether your DCT-equipped BMW serves as a track car or a highway cruiser, this pan ensures your transmission remains cool and efficient, minimizing the risk of overheating and wear.

DESIGN

Durable cast aluminum construction High-capacity design increases fluid volume (~7.5L capacity) Specifically designed to accept the OEM suction filter (28107842828) Hard coat black anodized with raw "Turner" logo KEY BENEFITS

A resilient, reliable replacement for the OE plastic fluid pan—crafted from aluminum for superior durability and features a threaded drain plug to prevent stripped threads Increased fluid capacity and cooling fins work together to provide a drastic increase in cooling Compatibility with the OEM suction filter ensures an easy service KIT CONTENTS

High-Capacity Aluminum Transmission Pan Includes gasket, drain plug, and installation hardware. DCT Suction Filter (optional) DCT Pressure Filter (optional) 8 Liters of DCTF-1 Fluid (optional) PRODUCT DEVELOPMENT

Our High-Capacity DCT Transmission Pan was designed, engineered, tested, and quality inspected by our Research and Development team in our Wadsworth, Ohio, facility. We strive for the highest level of precision and quality through leading-edge product development technology, including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer, and rigorous long-term product testing.

BMW Gray Filter Housing Cap - Blackline Performance Edition Oil is a premium upgrade designed to replace the standard OEM plastic oil filter housing cap. This high-quality billet aluminum cap enhances both the aesthetics and functionality of your BMW's engine.

• Durable Construction: Made from 6061 T6 aluminum with a hard anodized finish for superior strength and longevity.
• Improved Performance: Features better heat dissipation compared to the factory plastic cap, enhancing engine performance and reliability.
• Enhanced Aesthetics: Adds a sleek, high-performance look to your engine bay with 3D precision post-milled detailing and the G Insignia Oil Filter Cage Stabilizer.
• Easy Installation: CNC-formed hand grips and a 10mm Allen key maintenance port with a built-in scratch plate simplify the installation and maintenance process.
• Direct Replacement: Retains the factory oil filter stalk and is compatible with BMW S55 and most N series engines using BMW part 11427525334.
• Increased Longevity: Designed to increase the life span of your oil filter cap and provide a more reliable seal.

Engineered with an exclusive full-synthetic ester formula, these top-tier products are meticulously crafted to cater to various vehicles, including passenger cars, light trucks, performance vehicles, and marine applications. Offering an unparalleled level of quality, they boast an extensive range of viscosity options, ensuring the highest standards in the current market.

• Full-synthetic ester formula suitable for diverse vehicle types
• Exceptional protection, efficiency, and extended drain intervals
• Outstanding wear protection and friction reduction in varied conditions
• High detergency for increased cleanliness and prolonged drain intervals
• Enhanced fuel economy, improved ring seal, and elevated power output
• Unmatched high temperature stability and oxidation resistance for superior lubrication
• Natural high viscosity index providing a thicker oil film in crucial engine components
• Reduced evaporation, ensuring improved efficiency and ring seal
• Blended with polyol ester base stocks for multi-grade properties and enhanced lubricity
• Compatible with both conventional and synthetic motor oils
• Recommended for API SN/SM/SL/SJ/SH/SG/CF and ACEA A3/B3/B4 specifications