BMW Internal Engine Parts

When servicing your vehicle's VANOS system, get the job done easier with this socket specifically designed for the removal of the VANOS solenoid.

Features:

• 85mm from end to end
• 1/2" drive 
• 32mm with a depth of 70mm.

If you're not sure if your Vanos seals are bad then the only question you need to answer is if you've replaced them. Every unit from the factory came with the same failure prone o-rings and seals, even the re-manufactured units you can still get today. The only real fix is by replacing the seals and o-rings with material that is built to last in the oiled, extreme temperature environment found in these kits. 

A premium product replacement with easy to follow instructions makes rebuilding your Vanos unit a must. Even thought the power loss is barely felt it's the opposite result once you replace the seals, every car that gets rebuilt ends up wowing the customer and all of them saying they didn't realize what they lost. 

There are a number of symptoms that will plague your car as a result of these failing seals such as erratic idle, engine hesitation, stalling, and increased fuel consumption to name a few. If you've been chasing down any of these symptoms with no fix then this could be your issue.

These WPC-treated bearings are the best we have seen for the S62. WPC is a shot-peening treatment at a microscopic level. It's perfect for sensitive surfaces like bearings. The WPC treatment removes imperfections and high spots, while creating a surface that retains oil better than the original surface. This greatly reduces friction. The bearings in this kit are factory BMW bearings that are sent to WPC for treatment. The treated bearings are stronger with less metal fatigue and less friction than buying off-the-shelf bearings from the dealer.

Price is for a complete set of S62 upgraded rod bearings.

For the US E36 M3. Schrick 264/256 degree camshafts boost mid-high end power for that extra motivation at higher rpm. Low-end torque is not seriously affected due to the M50/M52s VAN0S System. And, higher profile cams work extremely well with an upgraded intake and exhaust. When upgrading the cams there are other areas you must take into consideration. Higher-flow fuel injectors, larger mass-air sensor, and custom programming are strongly recommended. Turner Motorsport sells complete intake & cam packages that boost power to over 290hp. See the Engine section under Camshafts for more info.

Cam Specs:
Intake - 264 degree, 11.2mm lift
Exhaust - 256 degree, 10.6mm lift

Schrick Technical Information / Specs

This item fits the following BMWs:
1993-1998 E36 BMW 325i 325is 325ic 328i 328is 328ic M3
1993-1995 E34 BMW 525i
1997-1998 Z3 BMW Z3 2.8
1998-1999 Z3 BMW M Roadster M Coupe

Still looking for more power after bolt-ons? High performance camshafts from Schrick are the way to go. These cams are a direct replacement for the stock cams and give a solid 15+ horsepower boost at the top end and great midrange torque increases too! More gains can be expected with intake and header upgrades and custom software tuning. A slightly lumpy idle is expected at cold start but will be smooth once at operating temperature. This set is just a great all-around cam upgrade for the S54!

These Schrick cams were initially developed for the M3 CSL but they also work great on the US and other non-CSL S54 engines as well. With more duration they are a great match to high flow headers, no cats, or CSL intake manifold upgrades. These are the new "cast" cams from Schrick which require new rocker arms (Schrick recommended or BMW part #11337833259). Professional installation is a must due to the intricacies with the double VAN0S.

Schrick Technical Information / Specs

This item fits the following BMWs:

• 2001-2006 E46 BMW M3
• 2001-2002 Z3 BMW M Roadster M Coupe
• 2006-2008 E85 BMW Z4 M Roadster M Coupe

SEE T#338745 BMW S54 3.2L Schrick Camshaft Set 280/272 12.5mm Lift is the perfect performance upgrade for enthusiasts seeking to enhance their engine's capabilities. With over 40 years of experience, Schrick is dedicated to producing high-quality camshafts that deliver exceptional power and reliability. Designed for both street and track applications, these camshafts offer an impressive balance of performance and drivability. The intake cam features a duration of 280, while the exhaust cam has a duration of 272, with a valve lift of 12.5mm. These new "cast" cams from Schrick closely resemble the stock E46 M3 CSL cams, ensuring a smooth idle and a significant increase in horsepower throughout the RPM range. With a peak gain of 15 horsepower and no loss in low-end torque, these camshafts are a top choice for BMW enthusiasts.

Key Benefits:

• Enhanced Power: Delivers a peak gain of 15 horsepower.
• Smooth Idle: Maintains a factory-like idle quality for everyday driving.
• Linear Power Increase: Provides a steady increase in horsepower from midrange to redline.
• Compatibility: Designed to fit the BMW S54 engine with new rocker arms required.
• High-Quality Construction: Crafted from top materials for strength and durability.