BMW Suspension Parts

Take total control of your E36's handling with the ECS Performance 2-Way Adjustable Coilover System. Built specifically for track use, this system bridges the gap between standard off-the-shelf coilovers and full-fledged motorsport suspension. These coilovers feature independent compression and rebound controls supported by external reservoirs; unlocking the precision tuning needed to shave seconds off your lap times.

Traditional 1-way coilovers force a single adjustment knob to balance both bump and rebound. These 2-way dampers eliminate that trade-off with fully independent compression and rebound controls. Use the 32 levels of compression adjustment to control front weight transfer under heavy braking, maximizing entry grip and allowing you to trail-brake deep into corners without understeer. 22 rebound levels fine-tune chassis recovery on brake release, keeping the front tires loaded through the apex for faster power-on exit speeds.

To maintain consistent performance during extended periods of performance driving, these dampers feature dedicated external fluid reservoirs that significantly increase total gas volume. During rigorous track use, rapid piston movement generates intense friction and heat, causing standard damper oil to thin out, aerate, and lose its damping force. By increasing overall fluid capacity, the external reservoirs effectively dissipate heat to keep peak oil temperatures down.

Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 255mm (10") to 315mm (12.4") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints (M10x1.5): Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability NOTE: If you've modified your vehicle's suspension with aftermarket struts or coilovers, the mounting location for the sway bar end link may have moved. To confirm fitment with our adjustable end links, please measure the distance between the sway bar and the mounting location on the strut body with the vehicle at ride height and confirm that it is within the 255 mm - 315mm range of adjustment.

Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left- and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 175mm (6.89") to 235mm (9.25") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints (M10x1.5): Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability NOTE: If you've modified your vehicle's suspension with aftermarket struts or coilovers, the mounting location for the sway bar end link may have moved. To confirm fitment with our adjustable end links, please measure the distance between the sway bar and the mounting location on the strut body with the vehicle at ride height and confirm that it is within the 175 - 235mm range of adjustment.

When high torque loads and aggressive corner exits push your chassis to the limit, stock differential mounts quickly become the weak link. The ECS Tuning Rear Differential Front Mount Upgrade Kit is track-engineered to lock down your rear diff, control axle wrap, and ensure immediate power delivery to the pavement.

Built to withstand severe track abuse, this kit eliminates hardware failure by replacing the undersized factory M12 bolt with an ultra-high-tensile Grade 12.9 M14x1.5 bolt. Surrounding the upgraded hardware is a track-spec 95A durometer red polyurethane bushing and a rugged 6061-T6 aluminum sleeve finished in Type II black anodizing. Engineered for maximum drivetrain stiffness, this upgrade ensures your differential stays precisely aligned under the harshest motorsport conditions.

Note: Upgrading to M14x1.5 hardware requires drilling and tapping the original M12x1.5 differential mounting hole. See T#58563042 for a complete kit that includes the proper-sized drill and tap.

When high torque loads and aggressive corner exits push your chassis to the limit, stock differential mounts quickly become the weak link. The ECS Tuning Rear Differential Front Mount Upgrade Kit is track-engineered to lock down your rear diff, control axle wrap, and ensure immediate power delivery to the pavement.

Built to withstand severe track abuse, this kit eliminates hardware failure by replacing the undersized factory M12 bolt with an ultra-high-tensile Grade 12.9 M14x1.5 bolt. Surrounding the upgraded hardware is a track-spec 95A durometer red polyurethane bushing and a rugged 6061-T6 aluminum sleeve finished in Type II black anodizing. Engineered for maximum drivetrain stiffness, this upgrade ensures your differential stays precisely aligned under the harshest motorsport conditions.