BMW Internal Engine Parts

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

Rocker Arm - E30 325e 325i 325is - E34 525i (M20)

We Price Match - Give Us A Call or Chat!

T#:3387

Part#: 11331271429

In Stock

$ 33.99

This product was last offered at the strikethrough price on
05-07-2026

$ 26.99 USD

Add to Wish List

Qty

$ 26.99 USD

Add to Wish List

If there is one weak point to the internals of the M20 engine, it's the camshaft rocker arms. They're actually designed to be the weak link to prevent more extensive damage elsewhere in the valvetrain. The rocker arm actuates the valves as the cam lobe makes contact. But sustained running at high RPM will cause the valves to 'float' or stay open which can lead to contact between the piston and the valves. If this happens too often, it will fatigue and snap the rocker arm. Therefore, any track driven E30 should have the rockers inspected or replaced often, along with a correct valve adjustment. And any high mileage M20 engine is running the risk of failure because of fatigue and weak valve springs. It's also a good idea to use new rocker arms any time a new cam is installed as the cam and the rocker wear together.

Replacement of the rocker arms can be done with the cylinder head in the car but more often, the head is removed. This makes removing the rocker shafts easier. Either way, a new cylinder head gasket set is recommended as it includes all of the gaskets and plugs that you would need. If the head stays on the car, the radiator may need to be removed to allow more access for the shafts to come out. Replacing the engine timing belt is not done at the same time and should be treated as a separate job.

These Febi M20 rocker arms are sold per rocker (order 12 for a complete set). You may also want to replace the eccentric adjusters as it's easy to do and worn eccentrics may prevent you from properly adjusting the valves afterward.

This item fits the following BMWs:
1984-1991 E30 BMW 325e 325es 325i 325ic 325is 325ix
1989-1990 E34 BMW 525i

Show More Show Less

E46 M3 Schrick DLC-Coated Rocker Arm

T#:342372

Part#: 041513800

In Stock

$ 263.99

This product was last offered at the strikethrough price on
07-07-2026

$ 165.00 USD

Add to Wish List

Qty

$ 165.00 USD

Add to Wish List

The roller rocker arms transfer the rotational force of the camshaft to open the intake and exhaust valves. One end is raised and lowered by the rotating lobe of the camshaft, while the other end acts on the associated valve stem. If a roller rocker arm has failed you may experience a constant ticking noise during engine operation, or alternatively if the rocker arm has broken, you will receive multiple misfires and a rough running engine.

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

T#:558795

Part#: VTT-CRANKHUB-1

In Stock

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Rocker Arm - M10 4 cylinder, M30 6 cylinder engine

We Price Match - Give Us A Call or Chat!

T#:6780

Part#: 11331271833

In Stock

Sale - Save 5% $ 30.99

This product was last offered at the strikethrough price on
07-13-2026

$ 29.44 USD

Add to Wish List

Qty

Sale - Save 5%

$ 30.99

This product was last offered at the strikethrough price on
07-13-2026

$ 29.44 USD

Add to Wish List

Replace your worn rocker arm with this unit. The rocker arms make contact with the camshaft and control the movement of the valves. Any time a camshaft is replace it is always a good idea to replace the rocker arms with new units. It is also a good idea to replace the rocker shafts that the arms mount on.
Since the late 1800’s Febi has been fabricating replacement metal parts. This history is self evident in the quality and vast amount of applications they service. With more than 34,000 repair solutions for cars and commercial vehicles you can be sure Febi has you covered.

This item fits the following BMWs:
1970-1976 2002 BMW 1600 2002 2002tii
1984-1985 E30 BMW 318i
1976-1981 E12 BMW 528i 530i
1982-1988 E28 BMW 533i 535i 535is
1989-1993 E34 BMW 535i
1982-1989 E24 BMW 633csi 635csi
1981-1987 E23 BMW 733i 735i
1988-1992 E32 BMW 735i 735il

Show More Show Less

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

T#:18733532

Part#: VTT-CRANKHUB-6

Ships in 1 Business Day

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Febi Valley Pan Cover With Seal N62 Engine - E53, E60, E63, E64, E65,...

We Price Match - Give Us A Call or Chat!

T#:363970

Part#: 11147507278

In Stock

$ 120.00

This product was last offered at the strikethrough price on
05-13-2026

$ 91.99 USD

Add to Wish List

Qty

$ 91.99 USD

Add to Wish List

Located in between the cylinder heads beneath the intake manifold.

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

T#:18733531

Part#: VTT-CRANKHUB-5

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Exhaust Valve - Priced Each

We Price Match - Give Us A Call or Chat!

T#:381763

Part#: 11347505731

In Stock

$ 27.99

This product was last offered at the strikethrough price on
03-26-2026

$ 22.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 27.99

This product was last offered at the strikethrough price on
03-26-2026

$ 22.99 USD

Limited Qty Sale

Add to Wish List

OEM Febi Eccentric Shaft - BMW N55 S55 3.0L

We Price Match - Give Us A Call or Chat!

T#:31522948

Part#: 11377589883F

Ships in 2 Business Days

$ 1,014.99

This product was last offered at the strikethrough price on
05-04-2026

$ 910.74 USD

Add to Wish List

Qty

$ 910.74 USD

Add to Wish List

The eccentric shaft is an important component of BMW's Valvetronic system, a form of variable valve lift control. If the teeth on the gear or the lobes have worn out, this can result in improper valve lift, decreased or abnormal performance, and even damage to cylinder head components. Replace your eccentric shaft with this high-quality part from OEM Febi to restore performance and eliminate valve lift issues without the marked-up price of a Genuine BMW eccentric shaft.

Show More Show Less

Schrick Intake Camshaft - E46 M3, MZ3, MZ4 (S54) - 288 Degree, 12.5mm...

T#:3572

Part#: TMS3572

Ships on Dec 3, 2026

$ 1,775.98 USD

Add to Wish List

Qty

$ 1,775.98 USD

Add to Wish List

E46 M3 Schrick 288 Degree Intake Camshaft with 12.5mm valve lift. Originally desinged for the M3 CSL but works great in a standard M3. A new rocker arm is required (Schrick or new BMW part #11337833259). This is a more agressive cam that the Schrick 280 degree cam that we also offer for the E46M3

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 272 Degree, 12.5m...

T#:11749

Part#: TMS11749

Ships on Dec 3, 2026

$ 824.99 USD

Add to Wish List

Qty

$ 824.99 USD

Add to Wish List

E46 M3 Schrick 272 Degree Exhaust Camshaft with 12.5mm valve lift. New rocker arms are required (BMW part #11337833259 or a new Schrick part).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Intake Camshaft - E46 M3, MZ3, MZ4 (S54) - 280 Degree, 12.5mm...

T#:11748

Part#: TMS11748

Ships on Dec 3, 2026

$ 1,867.99 USD

Add to Wish List

Qty

$ 1,867.99 USD

Add to Wish List

E46 M3 with S54 engine Schrick 280 Degree Intake Camshaft with 12.5mm valve lift. A new rocker arm is required (Schrick or new BMW part #11337833259).

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Camshaft - M20 288 degree

T#:3501

Part#: 05601880-00

Ships on Dec 3, 2026

$ 490.00 USD

Add to Wish List

Qty

$ 490.00 USD

Add to Wish List

SEE T#338236

Schrick Performance Camshaft Set - 238/272 - F80 M3, F82/83 M4 S55 ...

T#:637691

Part#: SCHCSSS55238/272

Back Ordered

$ 1,899.99 USD

Add to Wish List

Qty

$ 1,899.99 USD

Add to Wish List

High-performance camshafts are key to increasing the top-end power output of your S55 engine at high boost. 238/272 degree, 10.6mm/10.5mm lift. Perfectly compatible with OE valves, springs, VANOS, Valvetronic etc

Show More Show Less

Adjustment Unit - Outlet Cam - 11367536085

We Price Match - Give Us A Call or Chat!

T#:591757

Part#: 11367536085

In Stock

$ 328.99

This product was last offered at the strikethrough price on
04-16-2026

$ 304.99 USD

Add to Wish List

Qty

$ 304.99 USD

Add to Wish List

Upgrade your BMW's timing chain camshaft gear with this thicker gear positioned at the front of the engine, situated off the outlet side. This gear is commonly changed when replacing the timing chain.

Benefits:

Enhanced durability and performance
Ideal for replacing timing chain components
Improved reliability for engine operation

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 280 Degree, 12.5m...

T#:1259

Part#: TMS1259

In Stock

Sale - Save 5% $ 1,775.98

This product was last offered at the strikethrough price on
07-07-2026

$ 1,687.18 USD

Add to Wish List

Qty

Sale - Save 5%

$ 1,775.98

This product was last offered at the strikethrough price on
07-07-2026

$ 1,687.18 USD

Add to Wish List

E46 M3 Schrick 280 Degree Exhaust Camshaft with 12.5mm lift. This was originally desinged for the M3 CSL but works great in the standard M3. This cam is slightly more agressive than the "original" Schrick 272 degree (which we also offer). A new rocker arm is required (Schrick or new BMW part #11337833259).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 280 Degree, 12.5m...

T#:338216

Part#: TMS1259

Ships on Dec 3, 2026

Starting at $ 2,432.99 USD

Add to Wish List

Starting at $ 2,432.99 USD

Add to Wish List

E46 M3 Schrick 280 Degree Exhaust Camshaft with 12.5mm lift. This was originally desinged for the M3 CSL but works great in the standard M3. This cam is slightly more agressive than the "original" Schrick 272 degree (which we also offer). A new rocker arm is required (Schrick or new BMW part #11337833259).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

BMW US S50 6 Cyl. 284-Degree - Intake Camshaft

T#:554296

Part#: 0284E1840-0V1

In Stock

Sale - Save 15% $ 1,727.99

This product was last offered at the strikethrough price on
07-07-2026

$ 1,468.79 USD

Add to Wish List

Qty

Sale - Save 15%

$ 1,727.99

This product was last offered at the strikethrough price on
07-07-2026

$ 1,468.79 USD

Add to Wish List

Schrick has been dedicated to engine performance through the development of only the highest-quality camshafts for more than 40 years. They've created a bond with BMW enthusiasts nearly the entire time, offering options for both the street and track using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing. These are the same cams used by many high-end German tuners who are achieving sizeable gains with the US S50 engine. For the power-hungry, these cams are a great way to achieve a linear increase in horsepower from mid-range, up to redline. Duration Intake- 284 Duration Intake @ 1mm - 253 Intake Peak Timing - 122 Cam Lobe Lift Intake - 11, 9 Valve Lift w/o Valve Clearance Intake - 11, 9 Valve Clearance Intake - 0,25

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - N54

T#:558924

Part#: VTT-N54-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

Crank Pulley With Dampener

We Price Match - Give Us A Call or Chat!

T#:640241

Part#: 11237525135

In Stock

$ 221.99

This product was last offered at the strikethrough price on
03-31-2026

$ 156.99 USD

Add to Wish List

Qty

$ 156.99 USD

Add to Wish List

Febi Camshaft - E30, E34

We Price Match - Give Us A Call or Chat!

T#:19082

Part#: 11311716138

Ships in 2 Business Days

$ 368.34

This product was last offered at the strikethrough price on
05-15-2026

$ 292.43 USD

Add to Wish List

Qty

$ 292.43 USD

Add to Wish List

CAMSHAFT 11311716138 Manufactured by Febi

This item fits the following BMWs:
BMW 3 Series - 325i, 325i Convertible, 325is, 325ix
BMW 5 Series - 525i

--.

Show More Show Less

Spline Lock Crank Hub Solution

T#:8061334

Part#: VTT-N55-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

MINI F56 B36 B46 Crank Pulley With Dampener

We Price Match - Give Us A Call or Chat!

T#:4648710

Part#: 11238638614

Ships in 1 Business Day

$ 455.99

This product was last offered at the strikethrough price on
05-07-2026

$ 397.99 USD

Add to Wish List

Qty

$ 397.99 USD

Add to Wish List

MINI R53 R56 Rear Toe Adjustment Tool is designed for quick and precise rear toe adjustments on all MINI vehicles. This tool allows users to make adjustments efficiently using a standard 1/2" drive socket wrench, saving time during each alignment process.

Efficient Adjustment enables quick rear toe alignment on MINI vehicles.
User-Friendly compatible with a 1/2" drive socket wrench for easy use.
Precision Engineering ensures accurate adjustments every time.
Durable Construction CNC-machined from SCM440 Alloy Steel for long-lasting performance.

Show More Show Less

MINI R56 N14 N18 Adjustment Inlet Cam Unit

We Price Match - Give Us A Call or Chat!

T#:591758

Part#: 11367545862

Ships in 2 Business Days

$ 265.99

This product was last offered at the strikethrough price on
05-07-2026

$ 232.99 USD

Add to Wish List

Qty

$ 232.99 USD

Add to Wish List

Enhance your BMW's engine performance with this thicker timing chain camshaft gear, strategically situated toward the rear and off the intake side of the engine. Frequently changed during timing chain replacements, this gear offers enhanced durability and optimized functionality.

Thicker gear design for enhanced durability
Positioned toward the rear of the engine
Located off the intake side for optimal function

Show More Show Less

Febi Valley Pan With Gasket - E31, E32, E34, E38, E39, E53

We Price Match - Give Us A Call or Chat!

T#:366991

Part#: 11141742042

In Stock at Vendor

$ 116.99 USD

Add to Wish List

Qty

$ 116.99 USD

Add to Wish List

Experiencing a slow, mysterious, loss of coolant? Smell coolant when accelerating or braking? Time for a valley pan gasket service!

Spline Lock Crank Hub Solution W/ Crank Bolt Capture - N54

T#:18733527

Part#: VTT-CRANKHUB-2

Ships in 10 Business Days

$ 871.99 USD

Add to Wish List

Qty

$ 871.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Spline Lock Crank Hub Solution W/ Hardware Package - N54

T#:18733526

Part#: VTT-CRANKHUB-4

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

VTT N54 “Spline Lock” CrankHub Solution Package W/ Crank Bolt Cap...

T#:19395579

Part#: VTTCRANKHUBPKG

Ships in 10 Business Days

$ 934.99 USD

Add to Wish List

Qty

$ 934.99 USD

Add to Wish List

VTT is proud to offer the only complete N54 complete crank hub solution that does NOT require the crank to be drilled for pins. Our hub uses our proprietary “Spline Lock” technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). We spent many months testing, and retesting this design, utilizing well over 10 different samples to come to our final production version. During testing, our final hub managed to break our testing rig before slipping. These have been bench tested, and real-world tested on the VTT N54 race car spinning 8K RPM and making well over 900WHP. This technology means our hub installs the same as a stock hub, no drilling of the crank, which means MUCH less labor is involved and is reversible is ever wanting to be uninstalled leaving no holes in the crank. The “Spline Lock” is ONLY available with the VTT Crank bolt capture for the ULTIMATE Crank Hub solution for your BMW. These parts are designed to be used together, and the spline lock should not run without the CBC VTT “Spline Lock” Crank hubs are CNC manufactured from 440C tool Steel with a Rockwell rating of HRC60 for the ultimate in durability, and toughness. Hub Plus OEM bolt OEM Oil pump sprocket OEM oil sprocket retainer VTT Crank bolt capture

Show More Show Less

N54 Spline Lock Crank Hub Solution With Complete Package

T#:18733525

Part#: VTT-CRANKHUB-3

Ships in 5 Business Days

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Performance Camshaft Set - 238/272

T#:26904914

Part#: SCH-N52-238/272

Special Order: No Guaranteed ETA

$ 1,749.99 USD

Add to Wish List

Qty

$ 1,749.99 USD

Add to Wish List

Febi Cylinder Head Bolt Kit - E36, E39, E46, Z3

We Price Match - Give Us A Call or Chat!

T#:363745

Part#: 11121721938

Ships on Nov 11, 2026

$ 37.99 USD

Add to Wish List

Qty

$ 37.99 USD

Add to Wish List

Set of 14 stretch bolts for installing cylinder head

Schrick Camshaft Set - E46 325, 330, 530, X5 3.0, Z3 3.0 - 264/248 ...

T#:4048

Part#: E46-M54-SCHRICK

Ships on Dec 3, 2026

$ 2,915.38 USD

Add to Wish List

Qty

$ 2,915.38 USD

Add to Wish List

Schrick 264 degree (10.5mm lift) intake and 248 degree (10mm lift) exhaust cams provide a power boost at mid-high RPM range without software changes. As used in our 330i ZHP Project Car! These are also available for track / race applications in 272 intake and 256 exhaust durations. We also recommend purchasing Supertech High Performance Valve Springs Call us for details. Professional installation required for all Shrick Camshafts.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

Show More Show Less

Schrick Camshaft - E30 325i, E34 525 (M20) 304 degree

T#:338233

Part#: 05601040-00

Ships on Dec 3, 2026

Starting at $ 1,489.99 USD

Add to Wish List

Starting at $ 1,489.99 USD

Add to Wish List

Schrick's most aggressive cam for the M20 engine. The 304-degree will make big power at the top but there will be a loss of low-end torque so this cam is only recommended for cars that see most of their time above 4000 rpm. Schrick High Performance valve springs are strongly recommended. This cam has a 12.2mm lift and will not clear stock M20 pistons.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

Show More Show Less

Schrick Camshaft - E30 325i, E34 525 (M20) 284 degree

T#:338235

Part#: 05601840-00

Ships on Dec 3, 2026

Starting at $ 479.00 USD

Add to Wish List

Starting at $ 479.00 USD

Add to Wish List

E30 325i, E34 525 (M20) 284 degree Schrick Camshaft. This is Step 2 in Schrick's line of performance cams. The 284 degree cam will be great for owners who want to retain their driveability on the street and only need a modest boost in top-end RPM. Schrick recommends replacing the valve springs with high-performance springs for this application.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

Show More Show Less

Schrick Camshaft Set - E36 M3-spec - 252/244 Degree

T#:21521

Part#: TMS21521

Ships on Dec 3, 2026

$ 3,470.66 USD

Add to Wish List

Qty

$ 3,470.66 USD

Add to Wish List

These Schrick camshafts are the same specs as the stock US S50 cams -
Intake: 252 degree, 10.2mm lift
Exhaust: 244 degree, 9.5mm lift

With original S50/S52 cams in short supply, and a new set running over $2,000 from BMW, you can source new M3-spec cams from Schrick. These are the same specs as the US S50 engine and very close to the stock S52 cams. These make a great upgrade for M50 (325i, 525i) and M52 engines (328i, 528i) with the proper tuning. These bolt in just like the stock and M3 cams with no special hardware upgrades required - use your stock valve springs, lifters, etc. But for reliability we recommend replacing the lifters, valve springs, and retainers with new stock parts on high mileage engines.

Full cam specs: Schrick Technical Information / Specs

This item fits the following BMWs:
1993-1999 E36 BMW 325i 325is 325ic 328i 328is 328ic M3
1993-1995 E34 BMW 525i
1997-1998 E39 BMW 528i
1997-1998 Z3 BMW Z3 2.8
1998-1999 Z3 BMW M Roadster M Coupe

Show More Show Less

BMW S52/M52 6 Cyl. 264-Degree - Intake Camshaft

T#:300487

Part#: 261.E1.641-V2C

Special Order: No Guaranteed ETA

$ 1,398.99 USD

Add to Wish List

Qty

$ 1,398.99 USD

Add to Wish List

Schrick has been dedicated to engine performance through the development of only the highest-quality camshafts for more than 40 years. They've created a bond with BMW enthusiasts nearly the entire time, offering options for both the street and track using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing. These are the same cams used by many high-end German tuners who are achieving sizeable gains with the S50 and S52 engines. For the power-hungry, these cams are a great way to achieve a linear increase in horsepower from mid-range, up to redline. Duration Intake - 264 Duration Intake @ 1mm - 227 Intake Peak Timing - Cam Lobe Lift Intake - Valve Lift w/o Valve Clearance Intake - Valve Clearance Intake -

Show More Show Less

Schrick Camshaft Set - E36 M3, MZ3, M52 inc 2.8 1995-99 - 256/264 ...

T#:3859

Part#: TMS3859

Ships on Dec 3, 2026

$ 2,799.99 USD

Add to Wish List

Qty

$ 2,799.99 USD

Add to Wish List

For the US E36 M3. Schrick 264/256 degree camshafts boost mid-high end power for that extra motivation at higher rpm. Low-end torque is not seriously affected due to the M50/M52s VAN0S System. And, higher profile cams work extremely well with an upgraded intake and exhaust. When upgrading the cams there are other areas you must take into consideration. Higher-flow fuel injectors, larger mass-air sensor, and custom programming are strongly recommended. Turner Motorsport sells complete intake & cam packages that boost power to over 290hp. See the Engine section under Camshafts for more info.

Cam Specs:
Intake - 264 degree, 11.2mm lift
Exhaust - 256 degree, 10.6mm lift

Schrick Technical Information / Specs

This item fits the following BMWs:
1993-1998 E36 BMW 325i 325is 325ic 328i 328is 328ic M3
1993-1995 E34 BMW 525i
1997-1998 Z3 BMW Z3 2.8
1998-1999 Z3 BMW M Roadster M Coupe

Show More Show Less

Schrick Camshaft Set - E46 330, 530, X5 3.0, Z3 3.0 - 272/256 ...

T#:200185

Part#: TMS200185

Ships on Dec 3, 2026

$ 3,340.69 USD

Add to Wish List

Qty

$ 3,340.69 USD

Add to Wish List

Schrick 272 degree (10.9mm lift) intake and 256 degree (10.4mm lift) exhaust cams provide a power boost at mid-high RPM range without software changes. We also recommend purchasing Supertech High Performance Valve Springs Call us for details. Professional installation required for all Shrick Camshafts.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

Show More Show Less

Schrick Camshaft - E30 M3 276 degree

T#:203

Part#: TMS203

Special Order: No Guaranteed ETA

$ 1,503.99 USD

Add to Wish List

Qty

$ 1,503.99 USD

Add to Wish List

276-deg Performance Camshaft. This is the next step above the Evo 2/3 cams that we also sell and will produce greater top-end power with only slight loss in torque. This cam can be used on the intake side with a stock exhaust cam OR it can be used on the exhaust side with the 284-deg Schrick cam as the intake.

BMW Schrick Technical Specs

Schrick Technical Information / Specs br>
This item fits the following BMWs:
1988-1991 E30 BMW M3 - S14 engine

Show More Show Less

Schrick Exhaust Camshaft

T#:349689

Part#: 0261A1561-DV0

Special Order: No Guaranteed ETA

$ 1,721.99 USD

Add to Wish List

Qty

$ 1,721.99 USD

Add to Wish List

Schrick exhaust camshaft

Schrick Solid Lifter Conversion Kit (convert Hydraulic Lifters To Sol...

T#:359938

Part#: 086311700KT

Ships on Dec 3, 2026

$ 833.52 USD

Add to Wish List

Qty

$ 833.52 USD

Add to Wish List

One major hurdle for a track-only car is the limitation of the hydraulic valve lifters in the M50, S50-US, M52, S52-US, M52TU, and M54 engines. These effectively limit your revs to 7200-7300 RPM as the valves 'float' at higher revs, leading to piston-valve contact. By converting to a machined solid lifter, and upgrading other areas of the engine, you can configure the valve train to withstand high RPM running. Not only can you tune for more power, you can help prevent damage during a mild mechanical over-rev.

This kit includes the mechanical spacers to convert hydraulic lifter tappets to solid lifters. The lifter bucket remains in place with the Schrick solid tappet replacing the original. These work on all M50, M52, S50, S52 and M54 engines and were proven in normally aspirated as well as supercharged engines. A custom camshaft is required.

Professional installation and setup is mandatory as these require complete assembly of the head, checking valve lash, then dis-assembly and machining of the Schrick tappet to spec. This kit includes enough spacers for 24 valves. We also carry individual parts, if you are looking for single pieces. This price is for a full set of 24.

Show More Show Less

Schrick Camshaft Set - E46 M3, MZ3, MZ4 (S54) - 280/272 12.5mm Lift ...

T#:338745

Part#: E46M3SCHRICK

Ships on Dec 3, 2026

Starting at $ 2,692.99 USD

Add to Wish List

Starting at $ 2,692.99 USD

Add to Wish List

Still looking for more power after bolt-ons? High performance camshafts from Schrick are the way to go. These proved to be an excellent upgrade on our first Project E46 M3 and very similar to the stock E46 M3 CSL cams. Smooth as stock idle with a linear increase in horsepower from midrange all the way to redline. Peak gain was 15hp with no loss in low end torque. The duration of the intake cam is 280 and the exhaust is 272 with 12.5mm valve lift. These are the new "cast" cams from Schrick which require new rocker arms (Schrick or BMW part #11337833859). Professional installation is a must due to the intricacies with the double VAN0S.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

BMW S52/M52 6 Cyl. 256-Degree - Exhaust Camshaft

T#:637317

Part#: 0261A1561-02

Special Order: No Guaranteed ETA

$ 1,619.99 USD

Add to Wish List

Qty

$ 1,619.99 USD

Add to Wish List

Schrick has been dedicated to engine performance through the development of only the highest-quality camshafts for more than 40 years. They've created a bond with BMW enthusiasts nearly the entire time, offering options for both the street and track using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing. These are the same cams used by many high-end German tuners who are achieving sizeable gains with the M52 and S52 engines. For the power-hungry, these cams are a great way to achieve a linear increase in horsepower from mid-range, up to redline. Duration Exhaust- 256 Duration Exhaust @ 1mm - 227 Exhaust Peak Timing - Cam Lobe Lift Exhaust - Valve Lift w/o Valve Clearance Exhaust - Valve Clearance Exhaust -

Show More Show Less

Schrick Camshaft Set - E46 M3, MZ3, MZ4 (S54) - 288/280 12.5mm Lift ...

T#:340423

Part#: TMS201497

Ships on Dec 3, 2026

Starting at $ 3,551.99 USD

Add to Wish List

Starting at $ 3,551.99 USD

Add to Wish List

Still looking for more power after bolt-ons? High performance camshafts from Schrick are the way to go. These cams are a direct replacement for the stock cams and give a solid 15+ horsepower boost at the top end and great midrange torque increases too! More gains can be expected with intake and header upgrades and custom software tuning. A slightly lumpy idle is expected at cold start but will be smooth once at operating temperature. This set is just a great all-around cam upgrade for the S54!

These Schrick cams were initially developed for the M3 CSL but they also work great on the US and other non-CSL S54 engines as well. With more duration they are a great match to high flow headers, no cats, or CSL intake manifold upgrades. These are the new "cast" cams from Schrick which require new rocker arms (Schrick recommended or BMW part #11337833259). Professional installation is a must due to the intricacies with the double VAN0S.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 296 Degree, 12.5m...

T#:338218

Part#: 0415A1960-00

Ships on Dec 3, 2026

Starting at $ 829.00 USD

Add to Wish List

Starting at $ 829.00 USD

Add to Wish List

E46 M3 Schrick 296 Degree Exhaust Camshaft with 12.5mm lift. This cam is much more aggressive than either of the "standard" Schrick exhaust cams. A new rocker arm is required (Schrick or new BMW part #11337833259).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Camshaft - E30 325i, E34 525 (M20) 288 degree

T#:338236

Part#: 05601880-00

Ships on Dec 3, 2026

Starting at $ 490.00 USD

Add to Wish List

Starting at $ 490.00 USD

Add to Wish List

E30 325i, E34 525 (M20) 288 degree Schrick Camshaft. This is Step 3 in Schrick's line of performance cams and the best balance of power and driveability. Expect a big boost of power at the top end but a slight loss in low-end torque. Schrick recommends replacing the valve springs with their own for this application.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

Show More Show Less

BMW S14 4 Cyl. 284-Degree - Camshaft

T#:431

Part#: TMS431

Special Order: No Guaranteed ETA

$ 1,503.99 USD

Add to Wish List

Qty

$ 1,503.99 USD

Add to Wish List

Schrick has been dedicated to engine performance through the development of only the highest-quality camshafts for more than 40 years. They've created a bond with BMW enthusiasts nearly the entire time, offering options for both the street and track using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing. These are the same cams used by many high-end German tuners who are achieving sizeable gains with the S14 engine. For the power-hungry, these cams are a great way to achieve a linear increase in horsepower from mid-range, up to redline. Duration Intake - 284 Duration Intake @ 1mm - 253 Duration Exhaust - 284 Duration Exhaust @ 1mm - 253 Intake Peak Timing - 106 Exhaust Peak Timing - 106 Cam Lobe Lift Intake - 11, 5 Cam Lobe Lift Exhaust - 11, 5 Valve Lift w/o Valve Clearance Intake - 11, 5 Valve Lift w/o Valve Clearance Exhaust - 11, 5 Valve Clearance Intake - 0, 25 Valve Clearance Exhaust - 0,3

Show More Show Less

BMW S85 10 Cyl. 296/284-Degree - Camshaft Set

T#:589847

Part#: S85-296-284KT

Ships on Dec 3, 2026

$ 2,113.99 USD

Add to Wish List

Qty

$ 2,113.99 USD

Add to Wish List

This is one full set of Schrick camshafts, 4 cams total, for the S85 V10 M5 engine. These cams are the 296/284 degree version and include two intake cams and two exhaust cams. Professional installation is a must due to the complexity of the dual VAN0S V10 motor.

Show More Show Less

Schrick Camshaft Set - E90/E92 M3 - 292 Degree

T#:2500

Part#: TMS2500

Ships on Dec 3, 2026

$ 6,478.60 USD

Add to Wish List

Qty

$ 6,478.60 USD

Add to Wish List

This is one full set of Schrick cam shafts, 4 cams total, for the S65 V8 M3 engine. These cams are the 292 degree version, and includes two intake cams and two exhaust cams. Professional installation is a must due to the complexity of the dual VAN0S V8 motor.

Show More Show Less

Project Cars

SELECT YOUR BMW

Sub-Categories

Benefits:

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results