BMW Engine Parts

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent.  The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories.  These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

Fits the following BMWs:
2000-2006 E46 BMW 323/325/328/330

MSD Performance Coil Pack for MINI

Before ordering, check whether you need round or flat pin connectors for your MINI's coil pack. The type of pin is determined by the connectors that link the coil to the wiring harness. To check, slide the red locking tab to the right, press down on the tab, and pull the connector off the coil. Examine the pins to see if they are flat or round. Reattach the connector by pushing it back on until it clicks, then slide the red locking tab back to the locked position.

This high-performance coil pack is a popular upgrade among MINI owners looking to enhance their vehicle's performance over the stock coil. The installation requires removing the factory bolts from the old coil and modifying the MSD factory sleeves by drilling out 1/16" to fit the stock bolts.

Kits Include:

• MSD Coil Pack
• MSD Wire Set - Red
• Inductance: 7mH
• Maximum Voltage: 36,000 Volts
• Primary Resistance: 0.51 OHMs
• Secondary Resistance: 12K OHMs
• Turns Ratio: 77:1

Key Benefits:

• Upgraded performance over stock coil pack
• Enhances ignition efficiency and engine performance
• High voltage output of 36,000 volts for stronger sparks
• Low primary resistance of 0.51 OHMs for efficient energy transfer
• High secondary resistance of 12K OHMs for improved performance
• Durable construction for long-lasting use

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent.  The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories.  These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

This part fits the following BMW engines:
S54

This part fits the following chassis:
E46, Z3, Z4

Revitalize your Mini's performance with these spark plug wires and boots, designed to restore power and ensure smooth engine operation. Replace them at 60,000-mile intervals to maintain optimal performance. If you experience low spark or misfires and it's not due to the coil or spark plugs, faulty wires may be the culprit. Don't let rust buildup hinder performance—replace these wires to ensure happy motoring and reliable spark.

• Restores power and performance to your Mini
• Recommended replacement at 60,000-mile intervals
• Addresses issues such as low spark and misfires
• Prevents rust buildup for consistent spark delivery
• Includes plug wires for cylinder 1

These kits are designed to be installed inline with your stock low-pressure fuel pump (LPFP).  They provide approximately 50% more flow when combined with your stock pump.

Kit includes the following:

• SAE J30R10 E85 compatible fuel line
• 14ga fuel resistant wiring harness
• Quick connect female bullet connectors (2)
• Vent tube replacement clip
• Nylon cable ties (10)
• Stainless steel lock nuts (2)
• 10ga/14ga step-down butt splices w/E85 compatible heat-shrink tubing (2)
• Pushlock pump retention fittings (2)
• 14ga butt connectors w/heat-shrink tubing for pump removal to return to stock if/when desired (2)

  *Note:  Walbro does not warranty this pump for E85 use.  If your application requires an E85 certified pump you may want to consider selecting a Stage 2 fuel kit.

  ** IMPORTANT:  Do NOT attempt to run this kit inline with a Stage 2 kit.  The Stage 2 kit is a higher flowing kit and this will not only restrict the flow of the stage 2 kit, it will result in failures.

This is a complete Low-Pressure Fuel Pump (LPFP) upgrade that replaces your stock LPFP assembly with a new E85 certified one.  The new Walbro 450 pump provides approximately 100% more flow than stock and this assembly can be purchased one of three ways to meet your needs.

• Trade-in:
  • This option allows you to receive a rebuilt/upgraded stock bucket with a new Walbro 450 pump, filter, and fittings to swap out your stock LPFP assembly.  A $150 core deposit is included in the price that will be refunded when we receive your *stock bucket.
• New Build:
  • This option includes a new LPFP bucket that is upgraded with a new Walbro 450 pump, filter, and fittings.  No core deposit is required but you are eligible for a core refund of $50 should you elect to return your *stock bucket.

Both options include the following:

• A complete plug and play solution by simply replacing your stock bucket
• A new E85 compatible Walbro 450 pump
• A new Walbro filter
• A custom fitting that is tuned to optimize the venturi and pump output
• Spare vent tube clip
• Flow testing prior to shipping
• Recommended accessories:
  • Lock Ring Removal Tool 

 To be eligible for a core return, the bucket must be completely stock and undamaged. (Pump itself does not have to be functioning) 

+ International customers:  Due to different emissions requirements, the top portion of your fuel bucket (top hat) is different and doesn't have a large vent tube connection.  For this reason, we are no longer sending the top hat to international customers as this often causes confusion.  Those customers will simply re-use their current top hat when installing their Stage 2 pump.

- All Stage 2 assemblies are stock buckets that have been rebuilt and may show signs of being disassembled and rebuilt.  They are all flow tested and verified before being shipped.

For the US E36 M3. Schrick 264/256 degree camshafts boost mid-high end power for that extra motivation at higher rpm. Low-end torque is not seriously affected due to the M50/M52s VAN0S System. And, higher profile cams work extremely well with an upgraded intake and exhaust. When upgrading the cams there are other areas you must take into consideration. Higher-flow fuel injectors, larger mass-air sensor, and custom programming are strongly recommended. Turner Motorsport sells complete intake & cam packages that boost power to over 290hp. See the Engine section under Camshafts for more info.

Cam Specs:
Intake - 264 degree, 11.2mm lift
Exhaust - 256 degree, 10.6mm lift

Schrick Technical Information / Specs

This item fits the following BMWs:
1993-1998 E36 BMW 325i 325is 325ic 328i 328is 328ic M3
1993-1995 E34 BMW 525i
1997-1998 Z3 BMW Z3 2.8
1998-1999 Z3 BMW M Roadster M Coupe