BMW Tools & Specialty Equipment for BMW G80 M3 S58 3.0L

Protect your finish when working under the hood with a high quality Turner fender cover. Made from a synthetic leather layer with a goose flannelette backing for durability and protection. The Turner fender cover holds a tight grip to your fender or core support with four 9.5" magnets sewn into the top layer.

Features:

• Durable synthetic leather with the Turner logo
• Soft goose flannelette backing
• Four 9.5" integrated magnets

Dimensions:

•  Extra Long 20" x 47"

This tool comes in handy especially when working with an engine harness. Certain areas are always prone to corrosion and this tool makes having to re-pin a connector a breeze.

Unlike small screwdrivers, picks, and paper clips, these tools are the correct size and shape to remove and install tiny electrical pins and terminals at plastic block connectors with ease, and will not damage the connectors in the process.

Packaged in a blow molded case to keep everything secure and organized.

Proper torque is very important when it comes to working on engines. The importance comes from proper sealing and to keep from damaging threads.

Features:

• Reversible ½-inch drive click-to-stop
• Torque range of 10 to 150 ft-lb
• Accurate to within +/-4%
• 18 inches in length with a convenient carry case

Protecta socket are used to keep ugly scratch marks from showing up after torqueing down wheel lugs.

Features:

• Coated six-point deep-well impact sockets 
• Color coded mar-free exterior coatings that prevent nicks and scratches left by plain metal sockets
• 17mm, 19mm and 21mm Sockets included

Use these with your breaker bar or impact gun to remove the tightest wheel bolts and lug nuts: when reinstalling wheels, use them to final torque wheel fasteners to factory specifications.

Combine these with our torque limiting sockets and the Schwaben ½-inch torque wrench for a complete wheel fastener solution.

Tired of busting your knuckles from old hardened exhaust hangers?

This Schwaben tool removes the hanger by pressing on the steel hanger bracket and pulling the rubber hanger in one motion. Self centering force pin locks onto the pin while the flat paddle pulls off the rubber hanger from behind. Slim profile and a 25 degree offset works in tight areas.

When doing work where the mounts and support need to be removed from the engine or transmission having a engine support bar is wise. By using this engine support the stress is coming off of whatever components are still attached reducing future unnecessary repairs. The safety side of it is having the heavy engine and transmission firmly supported as it should be instead of questionable jack techniques.  

Features:

•  2" longer than most
• Deluxe transverse support for even more stability
•  Two angle chain hooks for safer and more stable chain support 
•  61" long and fully adjustable to any width
•  Weight rating is a full 1000 lbs.
•  Includes four rubber padded feet to prevent slipping and damage to cars finish 
• This tool features a dual hook design for holding engine or transmission in place
•  Powder coated for long life and durability

Note: It is important that chains are hooked to both sides of hook, like in photo to insure load is supported evenly. 

If you're removing trim panels and don't want to scratch or break any pieces then this is a must have. Formed for precision and constructed from plastic to be gentle with the finish.

Features:

•  Wide type remover
• Pull type remover
•  Handy remover
• Narrow type remover
• Upholstery Clip remover
• Angled Clip Panel Remover
• Fork Tip Flat Clip Panel Remover
• Clip Panel Remover
• Sharp Tip Flat Clip Remover
• Panel Remover
• Blunt Tip Flat Clip Panel Remover

All the right bits in one box. The perfect assortment to keep the job going.

Features:

• 10 fractional SAE hex, 9 Torx® tamper-proof, 9 Torx®

• 9 Metric hex bits, 9 slotted bits, 8 Pozi-drive, 8 Phillips, 4 square-recess, 4 tri-wing

• 3 spline, 3 Torq, 3 clutch, wing-nut driver, magnetic bit holder and socket bit holder

• Made of hardened Chrome Vanadium steel for years of dependable use

• Packaged in a handy blow molded case with individually marked bit slots for easy organization

The Schwaben 1/4" Drive 6 Point Deep Socket Set comprises thirteen 1/4" deep metric sockets, each featuring 6-point heads specially crafted for navigating those tricky, confined spaces. With a length of 50mm, these sockets ensure you can reach critical areas with ease.

Furthermore, our LIFETIME REPLACEMENT program provides you with added assurance, ensuring enduring performance and value. Improve your toolkit with the Schwaben 1/4" Drive 6 Point Deep Socket Set and confidently tackle any task at hand.

Features:

Access Tight Spaces: These deep sockets, measuring 50mm in length, are expertly designed to reach challenging, confined areas, making them perfect for intricate tasks.

Organized Storage: Included in the set is a practical sliding rail socket holder, helping you maintain a tidy and easily accessible socket arrangement.

Enhanced Grip: Knurled rings encircling the socket bodies ensure a secure hold, even when hands and sockets are covered in oil or grease, minimizing the risk of accidents.

Optimal Torque: The sockets are equipped with corner radii for superior torque distribution, safeguarding fasteners from damage and ensuring efficient performance.

High-Quality Material: Crafted from robust chrome vanadium steel (CR-V), these sockets offer superior wear resistance and toughness compared to high-speed steel, guaranteeing durability and extended lifespan.

Satin Chrome Finish: Not only do the sockets feature an attractive satin chrome finish, but they also provide excellent corrosion resistance, ensuring long-term quality.

Lifetime Replacement: Supported by our lifetime replacement program, this set delivers enduring value and peace of mind, making it a wise addition to your toolkit investment.

Includes:

• 4 mm
• 4.5 mm
• 5 mm
• 5.5 mm
• 6 mm
• 7 mm
• 8 mm
• 9 mm
• 10 mm
• 11 mm
• 12 mm
• 13 mm
• 14 mm