BMW Tools & Specialty Equipment for MINI

Protect your finish when working under the hood with a high quality Turner fender cover. Made from a synthetic leather layer with a goose flannelette backing for durability and protection. The Turner fender cover holds a tight grip to your fender or core support with four 9.5" magnets sewn into the top layer.

Features:

• Durable synthetic leather with the Turner logo
• Soft goose flannelette backing
• Four 9.5" integrated magnets

Dimensions:

•  Extra Long 20" x 47"

Proper torque is very important when it comes to working on engines. The importance comes from proper sealing and to keep from damaging threads.

Features:

• Reversible ½-inch drive click-to-stop
• Torque range of 10 to 150 ft-lb
• Accurate to within +/-4%
• 18 inches in length with a convenient carry case

Our aluminum wheel hanger makes it easy to remove and install wheels. Just thread the hanger stud into a wheel bolt hole and hang the wheel safely while you rotate tires or remove them for service or vehicle repair. (It's also great for keeping wheel bolt holes aligned on cars with spacers.)

Features:

• Longer & Lighter
• Made of 6061-T6 aluminum
• Anodized for hardness and good looks
• Knurled, non-slip handle has a drilled hole so you can hang it on a pegboard hook in your garage

Better still, order two: one for your garage and another for the emergency tool kit in you trunk.

Safety is always the most important factor when it comes to working under your car, jack stands are highly recommended. 

Features:

• Ultra light  jack stands only weigh 4.7 lbs each
• All aluminum construction with heavy-duty  flanged bases to safely stabilize loads
• 6 locking positions for a secure load in multiple heights
• Extra heavy duty load pin at .584 in. diameter with a posi lock ball to insure it stays in place
• Min. Height is 10.6
• Max Height is 15.4"
• Large 7" diameter base
• Outer support tube is 2-1/8" in diameter

Tired of busting your knuckles from old hardened exhaust hangers?

This Schwaben tool removes the hanger by pressing on the steel hanger bracket and pulling the rubber hanger in one motion. Self centering force pin locks onto the pin while the flat paddle pulls off the rubber hanger from behind. Slim profile and a 25 degree offset works in tight areas.

The Schwaben aluminum wheel hanger makes it easy to remove and install wheels. Just thread the hanger stud into a wheel bolt hole and hang the wheel safely while you rotate tires or remove them for service or vehicle repair. (It's also great for keeping wheel bolt holes aligned on cars with spacers.)

Features:

• Longer & Lighter
• Made of 6061-T6 aluminum
• Anodized for hardness and good looks
• Knurled, non-slip handle has a drilled hole so you can hang it on a pegboard hook in your garage

If you're removing trim panels and don't want to scratch or break any pieces then this is a must have. Formed for precision and constructed from plastic to be gentle with the finish.

Features:

•  Wide type remover
• Pull type remover
•  Handy remover
• Narrow type remover
• Upholstery Clip remover
• Angled Clip Panel Remover
• Fork Tip Flat Clip Panel Remover
• Clip Panel Remover
• Sharp Tip Flat Clip Remover
• Panel Remover
• Blunt Tip Flat Clip Panel Remover

This hand held Schwaben tool makes changing fluids an easy, quick task.The Schwaben fluid suction/fill pump suitable for oils, water and any non corrosive liquid.

Features 

• Comes with a flexible and a rigid tube. 
• Flow rate is adjustable for different functions.
• 350 ML capacity
• Cylinder is marked in 20 mL increments and fraction of quarts for accurate filling. 

Not for use with gasoline.

At almost half of the normal cost of Genuine BMW Installation Tool - No. 130190, this Schwaben BMW Fuel Injector O-Ring Tool Set is a perfect alternative to save money and ensure your have the proper tool for the job when it come time to service your fuel system. Make sure the job is done correctly the first time with this specialty item, relieving frustration and saving time all while preventing you from damaging critical seals or the injector itself that could otherwise be damaged if using the wrong tools for the job. 

This tool set includes all of the same components you would get with the BMW tool, the seal cutting pliers and seal installation components, made to exact specifications for perfect operation.

This complete set of extra deep sockets work great on cars equipped with extended studs. They also work as a long wheel nut socket for those deeply recessed nuts in wheels.

Features:

• 17mm, 19mm and 21mm socket in a sturdy blow molded case
• All sockets are 1/2" drive and a full 5-15/16 ( 150MM ) long
• Sockets are designed with inner bore to accept a 5" long stud

A professional quality flex ratchet features a fine satin finish designed for durability and easy clean up.

Features:

• Special designed 72T gear mechanism
• 5 degree of handle movement between gears 
• Flex head has 7 detent positions in a 180 degree swing
• Push button release holds socket tight until you are ready to release
• Ratchet is a full 290mm ( 11") long for extra leverage.

Limited Lifetime Warranty