Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 215mm (8.46") to 275mm (10.82") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints(M10x1.5): Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability

Stock rear lower control arms offer very little adjustment for alignment, especially in lowered vehicles, due to their use of an eccentric bolt. These aftermarket performance control arms from ECS Tuning are designed for maximum adjustability, allowing you to maximize handling and minimize tire wear.

To ensure maximum reliability, ECS Tuning's control arms are constructed from strong, lightweight 6061-T6 aluminum and feature a 303 stainless steel center turnbuckle that offers over 8 degrees of fast and precise camber adjustment. The inner bushing is a stock style serviceable OEM bushing for long life and inexpensive maintenance.

Features:

Durable construction suitable for the daily driver and track car alike
8+ degrees adjustment range for dialing in any suspension and wheel/tire setup
Center located adjuster for maximum clearance during adjustment
OEM-style bushing for long life and inexpensive service
Black anodized 6061-T6 aluminum with 303 stainless steel turnbuckle
Includes new hardware
*With the exception of the stance community, most enthusiasts will need no more than a few degrees of adjustment range. Total adjustment often is dependent on wheel/tire clearances.

Fine-tuning your coilover damping shouldn’t mean stripping out your rear seats or interior panels. On many applications, rear shock adjusters are hidden behind carpet, trim, or seatbacks, making quick adjustments a hassle.

The ECS Rear Damping Extension Kit solves that problem with a clean and functional solution. These flexible extensions relocate the adjustment knobs to an easily accessible point above the rear shock towers, letting you dial in your suspension from inside the cabin, no disassembly required.

Installation is straightforward: simply drill a small access hole in your interior trim and route the extension cables through. The adjustment knobs can be removed to allow the line to pass through smaller openings, minimizing cutting. For proper installation, be sure to fully loosen the set screw, insert the cable, then securely tighten it using the provided Allen key.

Kit Includes:

(2) Rear damping adjuster extension cables

Installation hardware and Allen key

A smart upgrade for track cars, daily drivers, or anyone who values easy access to suspension tuning, without compromising interior fit and finish.

Correct toe settings contribute to both stable steering and even tire wear. The SPC Performance wheel toe bar tool is designed to prevent vehicle drifting and ensure uniform tire wear. It includes a steel bar equipped with sliding adjusters and pointers to accurately assess the vehicle's toe alignment.

For wider wheel bases use T#386442!

To secure shocks and struts to their mounts, the retaining nut must be torqued to its proper specification using a torque wrench. An improper torque value may result in premature mount failure - or worse. Strut nut sockets allow for the use of an allen wrench to hold the damper shaft while utilizing your 1/2" drive torque wrench on the socket to achieve proper torque.

Kit Features:

• 18mm
• 19mm
• 21mm
• 22mm
• 24mm

When dismantling a suspension strut sometimes the securing nut can be difficult to access and the central strut itself needs to be held still while the nut is undone. This new Shock Absorber Tool Kit is designed to overcome these problems and make the job quick and easy.

The go-through design of the sockets and ratchet design allows the strut lock extensions to go right through the middle of the ratchet and socket. Five different strut lock extensions are included, to fit a variety of applications. Seven go-through deep sockets (16, 17, 18, 19, 21, 22 and 24mm) are included, plus a sliding T-bar.

Once the spring is compressed and the top plate is free, simply choose the correct strut lock extension and socket. Then fit the socket and the ratchet handle, and fit the strut lock straight through. The central strut is held steady, and the securing nut is quickly removed.

Specifically designed for repairing and replacing shock absorbers and struts
Contents: 7 - Go Thru' deep sockets: 16/17/18/19/21/22/24mm
3 x 1/2"D Hex bits: 6mm/7mm/8mm,
1 x sliding T-bar 1/2"D,
2 x slot bit sockets 5 x 8mm, 6 x 8mm x 1/2"D
Also includes 1 x 21mm Hex Go Thru' ratchet
Packed in a blow mold case for easy storage
For California Prop 65 warning see: www.P65Warnings.ca.gov.

Schwaben Shock Nut Socket - 16mm

The Schwaben Shock Nut Socket - 16mm is an essential tool for securely mounting shocks to their mounts. Designed to help achieve the correct torque specification, this socket allows the use of an internal hex wrench to hold the damper shaft in place while using a torque wrench to apply the correct torque. Properly torquing the retaining nut is crucial to prevent premature mount failure or loosening. This high-quality socket ensures a precise fit and reliable performance for maintaining your vehicle's suspension system.

Benefits:

• Allows accurate torquing of shock retaining nuts to prevent mount failure
• Designed for use with an internal hex wrench to secure the damper shaft
• Ensures proper torque application with your torque wrench
• Helps avoid premature mount failure and nut loosening
• High-quality construction for durable and reliable performance
• Compatible with 16mm shock nuts