Select Vehicle
BMW
Mini
Create an account to be able to build Wish Lists.
Please ensure your correct model is selected
If allowed in the rules these solid aluminum engine and transmission mounts offer many advantages over a urethane or Delrin mounts. It's no wonder that these mounts have found their way into the top BMW racers in the country. We originally developed these mounts for E36 and E46 World Challenge racing but they also work perfect in BMW Modified and SCCA club racing and SpecE46 (SE46). These are machined from solid aluminum and have zero deflection. The engine torque will cause a rubber or urethane mount to flex or deflect. The stiffer the material the less movement there is and the more torque is passed through the driveline (instead of being wasted winding up the mount). At the transmission end the flex-free solid mounts will give smoother, crisper shifts since the transmission is no longer dancing on the pliable mount. This puts the shift linkages in better consistent alignment. And unlike rubber or urethane the aluminum has zero wear and is not affected by leaking oil or other fluids so this is likely the last set of motor and transmission mounts you will ever need. We have designed these mounts so the engine is 5mm lower and the transmission is 1mm lower than the factory mounts. This helps lower the center of gravity for better balance and handling. We very strongly recommend using the transmission and engine mounts together as a complete kit. Mixing a rubber mount with a metal mount will cause undue stress on the mouting points and will lead to a failure. We never advise using a solid mount unless a corresponding solid mount is also used. This kit fits the E36, E46, Z3, and Z4 6 cylinder models listed below, including M3 models. 
Schwaben offers the right tools to make your next project a success. Everything from complex engine scanners to brake bleeders and spring compressors, Schwaben tools has you covered.
Some of the recommended use include but are not limited to:
Worn rubber differential mounts will lead to the differential twisting and shifting around in the rear subframe. Not only will this be noisy but it's bad for driver confidence and bad for the chassis as well. Even on fresh rubber bushings the differential has deflection and twist, especially if the car has been modified for more torque. Since the differential is centrally mounted in the rear subframe, with all suspension mounts interconnected, a differential with too much deflection will affect handling and could even damage the rear subframe.
These 88A urethane E46 M3 diff mounts are much stiffer than stock but still not as solid as our Turner aluminum/Delrin bushings. This set will resist twisting much better than the stock rubber mounts. Included is the front diff mount and two rear mounts in the cover.
Liqui Moly is an official sponsor of Turner Motorsport. We work closely with Liqui Moly to ensure your BMW is receiving optimal lubrication! Select your vehicle to make sure you are viewing the best Liqui Moly options for your application.
Interval oil changes are often recommended for differentials to ensure long-term reliability and maximum wear prevention. Fresh oil will prevent excess wear and gear damage, maintaining smoother operation.
Check your owner's manual to determine when it is best to flush your differential and what type and weight fluid to use when re-filling your system.
This 75w140 weight oil's multi-viscosity are perfect for ensuring protection in all climates and its synthetic composition allows for smoother operation even under the most demanding conditions.
APPROVALS:
API GL5
LIQUI MOLY RECOMMENDS THIS PRODUCT FOR VEHICLES THAT NEEDS TO COMPLY THE FOLLOWING SPECIFICATIONS:
BMW Hinterachsgetriebeöl
Ford WSL-M2C 192A
Scania STO 1:0
VME
ZF TE-ML 05D
ZF TE-ML 12D
ZF TE-ML 16G
ZF TE-ML 21D
Liqui-Moly is a German chemical company that offers top of the line engine oils, additives, and car care products that are designed to extend the life of your engine and ensure the best lubrication and cleanliness off engine and transmission components possible. With more than 50 years of experience and reviews across the world from magazines and race teams, Liqui-Moly proves time and time again why they are one of the most innovative lead forces of performance automotive chemicals in the world.
Genuine BMW hex bolt. M12X1,5X28
Be sure to replace your hardware with any flywheel removal service such as the rear main seal or clutch and flywheel.
If your clutch switch is bad, it will prevent the car from starting and seem similar to a bad starter, you will turn the key and nothing will happen. Replace yours to start your vehicle again.
Genuine BMW Module, Clutch Switch
This item fits the following BMW Chassis:
E39 M5,E46 M3,E85 Z4M,E39,E46,E85 Z4,E86 Z4
Most flywheel bolts are single-use only. They stretch when tightened. New mounting bolts are required with any flywheel swap. This is a set of 8 OE BMW M12x1.5x50mm flywheel bolts to help complete the job.
Replaces BMW #11221730533.
Commonly used when replacing axle shaft boots.
Features:
Installing wheel bearings correctly can prove to be a difficult task. With the compression fitting in the race, it makes it possible to install it without it being plumb. Well, we have your solution. With this specialty tool from BMW, you can ensure that your wheel bearing is installed correctly every time.
Comparable to OE tool 83300491905.
Revitalize your driving experience with ECS Tuning's In-House Engineered Performance Polyurethane Differential Bushings. Say goodbye to soft factory rubber bushings and their deflection. These innovative bushings provide a substantial improvement in the connection between your right foot, the chassis, and the wheels. The outcome is a crisper power transfer from the differential to the wheels, resulting in enhanced throttle control for various driving activities. Notably, these polyurethane bushings achieve these benefits without the harshness or vibration often linked to delrin or solid differential mounts.
Manufactured using a robust 88A durometer polyurethane and a black anodized 6061-T6 aluminum sleeve, these bushings offer superior resistance to chemicals, ozone degradation, road salt, and general wear and tear. This translates to an extended service life.
Enhance your driving experience with ECS Tuning's Performance Polyurethane Differential Bushings. These meticulously engineered bushings offer a direct connection between your right foot, the engine, and the chassis, making them an essential upgrade.
Unlike delrin or solid differential mounts, these bushings deliver improved performance without introducing harshness or excessive vibration.
Crafted from durable 88A durometer polyurethane and enhanced with a black anodized 6061-T6 aluminum sleeve.
Resistant to chemicals, ozone degradation, road salt, and general wear and tear, ensuring a longer service life.
Shifter slop is a common complaint among all BMW models. Some of that play comes from the bushings where the shifter carrier mounts to the transmission. The original rubber carrier bushings don't last very long and when they get too soft the shifter flops around. These Delrin bushings have almost no deflection and will last much longer than the factory rubber, giving you precise shifting for many years.
Note: this is only one part of the shift linkage and there may be other components that need replacing to improve shifting feel.
New carrier bushing pins are included.
E46 M3, Z4 M Front Wheel Hub Assembly with Bearing. This is an OEM Wheel Bearing Hub Assembly. Available from FAG or GSP. Both meet all of the OE specifications for fitment and life.
FAG is an OE supplier to BMW as well as several other German marques. (SKF does not have a front bearing assembly for the E46 M3).
GSP is a high-quality supplier for aftermarket suspension components. They have quickly position themselves as an industry leader, and pride themselves on offering high-quality alternatives to their expensive OEM counterparts.
