BMW Engine Parts for BMW Z4 M Roadster S54 (2003-2008)

The NOCO GBC010 12V Accessory Kit is designed to connect directly to the XGC IN and OUT ports of NOCO Boost jump starters. This kit allows you to effortlessly power your preferred 12-volt devices directly from a GB70, GB150, GB250+, GB251+, or GB500+, such as a tire inflator, vacuum, coffee maker, fan, cooler, and more. Constructed from high-conductivity 16AWG 100% copper wire, it boasts a rated capacity of 15 amperes.

Features: 

• Recharge NOCO Boost UltraSafe Lithium Jump Starters from a vehicles 12-volt power source.
• Compatible with NOCO Boost UltraSafe Lithium Jump Starter models GB70, GB150 GB250+, GB251+ and GB500+.
• Power 12-volt device like a tire inflator, vacuum and more.
• High-conductivity 16 AWG copper wire and rated capacity of 15-amperes.
• Molded strain reliefs prevent unwanted strain on the XGC wire connections.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

The GENPRO10X2 is an upgraded version of our GEN2 with enhanced features. This model is 19% smaller yet delivers 33% more power, making it one of the most high-performing onboard marine battery chargers NOCO has ever produced. It's a two-bank onboard battery charger with a 20-amp rating (10 amps per bank) designed for 12-volt batteries, including marine, boat, starter, and deep-cycle batteries. You can independently charge and control each battery bank using selectable charging modes such as 12V, 12V AGM, 12V Lithium, and 12V Repair Mode, suitable for all types of lead-acid and lithium-ion batteries.

Features: 

• A two-bank on-board battery charger rated at 20-amps for 12-volt batteries, including marine, boat, starter, and deep-cycle batteries.
• Independently charge and control each battery bank with selectable charging modes - including 12V, 12V AGM, 12V Lithium, and 12V Repair Mode - for all types of lead-acid batteries.
• An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates.
• Charges batteries as low as 1-volt. Or use the all-new force mode that allows you to take control and manually begin charging dead batteries down to zero volts.
• Automatically detects battery sulfation and acid stratification to restore lost battery performance for stronger engine starts and extended battery life.
• It's not just a trickle charger; it's an advanced battery maintainer. A fully automatic, worry-free battery charger for everyday use - 24/7 - with zero overcharge.
• A simplified mounting system allows for quick and easy installations in any direction - even up-side-down - with an integrated anti-vibration backing to isolate shock, vibration, and noise.
• A fully-sealed and waterproof onboard battery charger with an ingress protection rating of IP68, but has survived brutal life cycle testing, including thousands of hours underwater.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

BMW S54 3.2L VANOS Elimination Kit - Full Kit | VAC Motorsports is designed to replace the original VANOS unit on the S54 engine, offering a comprehensive solution for performance enthusiasts and racers. Engineered and tested by VAC Motorsports, this kit allows for precise camshaft timing adjustments and is ideal for those using standalone ECUs that do not control the dual-VANOS system.

• Enhanced Performance: Allows for full adjustment of camshaft timing, enabling optimization of camshafts for maximum performance.
• Engineered for Racing: Ideal for racing applications and standalone ECU setups that do not manage the dual-VANOS unit.
• High-Quality Components: Includes a billet 6061-T6 anodized black VANOS elimination plate and adjustable camshaft hubs made from durable 4140 alloy steel.
• Complete Kit: Comes with a block-off plug, using OE O-rings to replace the original oil supply valve, and all necessary hardware for installation.
• Versatile Fit: Compatible with all S54 engines and those swapped into other chassis.

Kit Includes:

• Billet 6061-T6 Anodized Black VANOS Elimination Plate
• (2) Adjustable Camshaft Hubs made from 4140 Alloy Steel
• Block OFF Plug – Uses OE O-Rings and replaces OE Oil Supply Valve
• All Required Hardware
• Installation Instructions

NOTE: ONLY COMPATIBLE WITH AFTERMARKET ECUs

Schrick has been dedicated to engine performance through the development of only the highest quality camshafts for more than 40 years. They've created a bond with BMW enthusiasts nearly the entire time, offering options for both the street and track using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing.

These cams are a direct replacement for the stock cams and give a solid 15+ horsepower boost at the top end and great midrange torque increases too! More gains can be expected with intake and header upgrades and custom software tuning. A slightly lumpy idle is expected at cold start, but will be smooth once at operating temperature.

These Schrick cams were initially developed for the M3 CSL, but they also work well on the US and other non-CSL S54 engines. With more duration, they are a great match to high-flow headers and CSL intake plenum upgrades.

KIT INCLUDES

Schrick 280-Degree Exhaust Camshaft Schrick 288-Degree Intake Camshaft 24 Turner Motorsport DLC-Coated Performance Rocker Arms NOTE: Camshaft replacement requires multiple special tools. We offer the Genuine BMW Camshaft Press (T#171829) and a Schwaben Camshaft Alignment Tool Set (T#395239) to aid in installation.

13 of these rubber O-ring seals are used in the fastening of the valve cover of the S54 BMW. This is a single o-ring.
When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Genuine BMW ENGINE RUBBER SEAL

Includes connector housing with terminals and seals. Commonly used for the camshaft position sensor.

ECS Tuning replacement harness connectors include all necessary pins and wire seals for a complete harness repair. Whether you have a broken harness connector or need a complete wiring repair, we have the components you need.

Each connector includes an additional terminal in case one becomes lost or damaged during installation.

*OEM cross reference PN# 12521433917 - Commonly used for the camshaft position sensor.

Please reference the original part number from the existing connector to confirm fitment, before ordering.

Suggested tools:

Suggested crimping pliers: T#387193
Wire De-pin tools:
12pc De-Pin Tool Set - T#386379
23pc De-Pin Tool Set - T#641943

Plastigage Set is an essential tool for accurately measuring the clearances of engine rod and main bearings without the need for expensive micrometers. This set is ideal for ensuring proper engine assembly by helping you choose the correct size replacement bearing inserts. Designed to cover all automotive engines, the Plastigage Set provides precise measurements to maintain optimal engine performance.

• Accurate Measurements: Measures clearances of engine rod and main bearings, ensuring proper fitment.
• Cost-Effective: Eliminates the need for expensive micrometers, offering a budget-friendly solution.
• Universal Application: Suitable for all automotive engines, making it versatile for various applications.
• Complete Set: Includes sizes .001" - .003" (green) and .002" - .006" (red) to cover a wide range of measurements.

Includes connector housing with terminals and seals. Commonly used for the engine oil level sensor.

ECS Tuning replacement harness connectors include all necessary pins and wire seals for a complete harness repair. Whether you have a broken harness connector or need a complete wiring repair, we have the components you need.

Each connector includes an additional terminal in case one becomes lost or damaged during installation.

*OEM cross reference PN# 12521433915 - Commonly used for the engine oil level sensor.

Please reference the original part number from the existing connector to confirm fitment, before ordering.

Suggested tools:

Suggested crimping pliers: T#387193
Wire De-pin tools:
12pc De-Pin Tool Set - T#386379
23pc De-Pin Tool Set - T#641943