Showing 7510 results for ""

PRESSURE BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

FLUID CATCH BOTTLE:

keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

This is an OEM INA tensioner pulley, also known as the adjusting pulley and lower pulley. This pulley is mounted on the belt tensioner near the center of the belt assembly. The upper and lower pulleys are known to be the primary sources for 'belt squealing'. This pulley is also encased in rubber which will crack over time. If left without service the rubber could fail completely, chucking the belt and leaving you stranded. Replacement is a very simple procedure and can be done anytime the fan is off the engine (belt replacement, water pump service, alternator replacement, etc).

This pulley is mounted along with the hydraulic belt tensioner but can be replaced on its own. It is used for the main drive belt on the M50-M54 family engines (M50, M50TU, M52, S52, M52TU, M54, M56, and S54 engines). This is the same belt that covers the water pump/alternator/power steering systems. Replacement is a very easy procedure (requires fan removal) and will have your engine purring in no time. Belt replacement is strongly recommended at the same time. If you have a mechanical belt tensioner, the pulley can only be replaced with a new tensioner.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

If you need the hydraulic belt tensioner, click here.

This item is 70mm Diameter. Please check the diameter before ordering.

This tensioner pulley fits the following BMWs:
1991-1995 E34 525i (M50 engine)
1992-1999 E36 325i, 325is, 328i, 328is, 323is
1995-1999 E36 M3 (M3 3.0 & M3 3.2 liter)
1997-2003 E39 525i, 528i, 530i - Only for Hydraulic Tensioner
1999-2000 E46 323i, 323Ci, 328i, 328Ci - Only for Hydraulic Tensioner
2001-2005 E46 325i, 325Ci, 325xi, 330i, 330Ci, 330xi - Only for Hydraulic Tensioner
2001-2006 E46 M3 coupe & convertible - Only for Hydraulic Tensioner
2000-2006 X5 3.0 liter (E53 chassis)
2004 E60 525i, 530i (M54 engine)
1997-2002 Z3 & MZ3 2.5, 2.8, 3.0, M Roadster, M Coupe
2003-2009 Z4 M Coupe and Roadster

Common point of failure is the N52/N54 Oil Filter Housing Gasket. When leaks occur here, oil can get on your belts, among other important components, causing engine failure. Replace yours today to avoid future troubles!

Genuine Bmw Gasket - 11428637821

Upgrade your BMW's front-end performance with the Genuine BMW Upper Spring Pad. This crucial component serves as a bushing, fostering a seamless connection between the spring and spring plate. Over time, worn pads can lead to disruptive front-end noise. Invest in this Genuine BMW part to restore your vehicle's optimal functionality and eliminate disturbances in your ride quality.

• Genuine BMW part ensures precise fit and compatibility.
• Acts as a crucial bushing for the spring and spring plate.
• Prevents front-end noise caused by worn pads.
• Restores optimal performance and ride quality.

Rubber seals are often hardened and damaged by excessive heat and constant temperature changes causing them to become brittle and crack or split. If your seal has split, replace it with a new Elring seal for long reliability and to prevent further problems.

Elring is one of the biggest OEM names in the manufacturing of high quality gaskets that are available for very affordable prices. Elring has supplied many automotive names for years with the gaskets that seal your car's components from day 1 so you can rest assured that these components will last for a long time to come!

Fits the following BMW's:
E60, E61, E70, E82, E83, E88, E85 E86 E89 Z4, E9X, F01, F02, F07, F10

Fits the following Engines:
N52 N54 N55 S65 N63