Protecta socket are used to keep ugly scratch marks from showing up after torqueing down wheel lugs.

Features:

• Coated six-point deep-well impact sockets 
• Color coded mar-free exterior coatings that prevent nicks and scratches left by plain metal sockets
• 17mm, 19mm and 21mm Sockets included

Use these with your breaker bar or impact gun to remove the tightest wheel bolts and lug nuts: when reinstalling wheels, use them to final torque wheel fasteners to factory specifications.

Combine these with our torque limiting sockets and the Schwaben ½-inch torque wrench for a complete wheel fastener solution.

WHEEL STORAGE RACK:

Now you can stack your extra wheels without the danger of scratches and scuffs. This wheel storage rack keeps your wheels spaced apart, and being on locking casters, allows you to easily move the whole set anywhere in your garage or shop at one time. Sturdy steel construction and a wide base means this wheel rack won't tip over. Holds up to 275 lbs - enough for most any wheel & tire set.

Fits up to 8½" wide wheels, depending on offset

TIRE STACK COVER:

This tire stack by Schwaben is the solution to keeping your tires and wheels clean while in storage.

• Works with 4 tire stacks and works great with our Schwaben Wheel Tree (ES2710754).
• Durable 150D coated material is rated for outdoor use.
• Cover is a large 32" wide X 46" tall.
• Fitted with a long 29" zipper up the side for easy installation and removal.
• Nylon draw string at the bottom allows for a good snug fit.
• Includes a handy storage pouch if not in use.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Schwaben Protecta Sockets have color coded mar-free exterior sleeve  that prevent nicks and scratches left by plain metal sockets. Internal spring loaded magnet holds lug nut in place.

Features:

• 17mm, 19mm and 21mm Sockets included in a blow molded case.
• All sockets are 1/2" drive
• 3-3/8" ( 86mm) long

Use these with your breaker bar or impact gun to remove the tightest wheel bolts and lug nuts: when reinstalling wheels, use them to final torque wheel fasteners to factory specifications.

Handsome sockets are shop tough, plated to resist corrosion, and color-coded for fast identification. Set takes up less room in your tool box than conventional torque sticks, and comes in a handy blow-molded case for portability and easy organization.

Torque-limiting socket set prevents over-tightening of wheel bolts and lug nuts. Attach them to your ½-inch breaker bar or impact gun and tighten the wheel bolts or lugs until the socket stops tightening at 74 ft-lb (100 Nm). Then final-tighten the wheel fasteners to the recommended specification using a torque wrench.

Features:

• 17, 19, and 21 mm six-point impact sockets to fit most metric wheel bolt heads and lug nuts.
• Combine these with our Protecta Sockets and the Schwaben ½-inch torque wrench for a complete wheel fastener solution.

Correct toe settings contribute to both stable steering and even tire wear. The SPC Performance wheel toe bar tool is designed to prevent vehicle drifting and ensure uniform tire wear. It includes a steel bar equipped with sliding adjusters and pointers to accurately assess the vehicle's toe alignment.

For wider wheel bases use T#386442!

Installed extended wheel studs and would love to be able to change wheel spacers as needed? But wait, if you have a flat tire or want to change it up at the track. But now your lug wrench is not deep enough to reach the nuts.

Features:

• This specially made socket features 17mm male hex on one end and 17mm socket on the other
• Works to extend reach between wrench and lug nut
• Keep inside your glove box so it is ready for any tire change on the road or on the track

NOTE: Not for use with impact.