All vehicles will lose some degree of performance due to heat soak under the right operating conditions.  Engine management systems constantly monitor operating conditions and modifying parameters based on sensor inputs. BMW integrated the intake air temp sensor in the MAF housing on models such as the E39 M5, and, being sandwiched behind a hot radiator and in some applications next to an even hotter valve cover, this is less than ideal for performance applications. Absorbing excess heat from its surroundings, the MAF can’t shed it fast enough, and the ECU reads an inaccurately high intake air temperature. Compensating for this false hot air measurement, the ECU pulls timing and runs a richer fuel mixture, resulting in a significant loss of torque.

What can you do?  Locate an intake air temp sensor in a location where it can properly measure incoming air temps and where it's less prone to heat soak. Mounting the sensor further away from the heat source and isolating it from the MAF housing, it can both resist the effects of heat soak longer and respond to temperature changes more quickly.  The result is you’ll experience reduced torque loss and more consistent power output when you’re pushing your engine hard. 

The Turner engineering team was initially skeptical of the claimed performance benefits of this modification. They first set out validate the functionality and performance benefit of a temp sensor relocation. Replicating stop-and-go traffic heat soak in a 2001 540i was a simple task in a controlled environment - their dynometer. First the car was heat soaked to simulate being stuck in traffic or moving at low speeds by running the car four times on the dyno with the dyno's cooling fans disabled. The fans were then turned on for three more runs to observe the recovery rate once air flow was reintroduced. The test: following this procedure once with a stock IAT, and once with their relocation kit in place. 

The result? Turner recovered 11lb-ft torque at 2500rpm through use of their relocation kit, with even greater recovery to be found for M5 owners. Here are the heat soak-related torque losses Turner experienced:

Stock IAT location:
18rwtq at 2500rpm
10rwtq at 3000rpm
9rwtq at 3700rpm

Turner IAT Relocation:
7rwtq at 2500rpm
5rwtq at 3000rpm
5rwtq at 3700rpm

**Click here for installation instructions**

The Turner engineering team designed a complete plug and play kit (unlike all other options on the market) that makes for quick, easy, and reversible installation. Weather-sealed connectors keep out the elements, while sheathed wiring offers a clean appearance underhood. With a harness nearly 3 feet long - the Turner IAT relocation kit offers flexibility in positioning, but not too long that you're left with unsightly excess wiring. Turner recommends positioning the sensor in a location away from engine heat, but still within the intake ducting to achieve accurate intake temp readings - such as the far side of the base of the airbox. Vehicles with cold air intakes with cone-style filters can even position the sensor in the end of the filter. Simply drill a hole in your (cool) location of choice and plug in the harness. More information including installation instructions and some good examples of sensor mounting locations can be found in our DIY PDF. 

We include everything you need to relocate your IAT, just select your desired sensor brand below - Genuine BMW or original equipment Beru.

Also the perfect plug-n-play option for anyone looking to upgrade their intake to utilize an Alpha-N tune!

Note for vehicles with M62 engine: applicable to 1999 and up

Here at Turner we understand the importance of an upgrade that will get the results you need on the track and still be tolerable on the drive around town. When it comes to control arms on the track, making them as stiff as you can (usually using solid mounts) is the best way to increase your driving precision by eliminating the deflection of rubber. The next best thing to create a balance would be to stiffen up the control arm with polyurethane, giving you the option of a more stock like feel with 80a or closer to the solid feel with 95a durometers.

When it comes to the E36 chassis you also get the options of choosing a stock centered design or going with the E30 inspired offset bushing to increase castor, further taking advantage of improvd handling. These poly bushings will give your control arms a direct connection between your suspension and the body of the car eliminating the slop felt under take-off and braking so you feel more in control of your vehicle. 

This item fits the following BMWs that use a centered-style bushing: 

1984-1991 E30 BMW 318i, 318is, 325, 325e, 325es, 325i, 325is 
1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic
1996-1999 E36 BMW M3 S52
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i MZ3 M Coupe M Roadster 

If allowed in the rules these solid aluminum transmission mounts offer many advantages over a urethane or Delrin mounts. It's no wonder that these mounts have found their way into the top BMW racers in the country. These are machined from solid aluminum and have zero deflection, engine torque will cause a rubber or urethane mount to flex or deflect allowing more torque to passed through the drive line (instead of being wasted winding up the mount). This puts the shift linkages in better consistent alignment. And unlike rubber or urethane the aluminum has zero wear and is not affected by leaking oil or other fluids so this is likely the last set of transmission mounts you will ever need. We very strongly recommend using the solid transmission and engine mounts together as a complete kit, mixing a rubber mount with a metal mount will cause undue stress on the mounting points and will lead to a failure. We never advise using a solid mount unless a corresponding solid mount is also used.

These are a no-compromise design for all-out racing use, full solid aluminum mounts should not be used on street-driven cars since there is no material to absorb vibration making these quite harsh for regular street use (track cars don't care about noise).

Product features and benefits:

• Crisper throttle response, positive shifter location, direct power transfer
• Precision machined billet 6061-T6 aluminum housing
• Grade 10.9 stud - fear not, big turbo owners
• Engineered in-house and made in America

This item fits the following BMWs: 
1989-1995  E34 BMW  525i 530i 535i 540i M5 
1992-1998  E36 BMW  318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 
1997-2003  E39 BMW  525i 528i 530i 540i M5 
1999-2005  E46 BMW  323i 323ci 325i 325ci 328i 328ci 330i 330ci M3 
2008-2012  E82 BMW  128i 135i 1M Coupe 
2006-2011  E90 BMW  325i 328i 330i 335d 335i - Sedan 
2006-2012  E91 BMW  328i - Wagon 
2007-2013  E92 BMW  328i 335i 335is - Coupe 
2007-2013  E93 BMW  328i 335i - Convertible 
1997-2002  Z3 BMW  Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe ​

Set of 2 universal 2.5" inlet to 3.5" outlet exhaust tips.

Over the years, it is not uncommon for exhaust tips to be damaged and corroded, becoming a "sore spot" of your BMW. To remedy this unsightly feature, we now offer our very own exhaust tips! Featuring stainless steel construction and a simple, yet sporty design, this exhaust tip will look perfectly at home on almost any model.

Features & Specifications:

Swivel feature for perfect alignment of the exhaust tips in the rear bumper
2.5" Inner Diameter
3.5" Outer Diameter
Brushed Aluminum Finish
Double Wall Construction
Angle Cut Style
Includes Stainless Steel Clamp

Our experience with spherical front control arm ball joints go back to those we designed and used in our IMSA E90 328i and E92 M3 racecars (GS class Champions in 2011).  We wanted to offer e30, e36, and e46 owners similar levels of handling precision and control for the track and street, but weren’t satisfied with the other options out there. Instead of a Delrin® bushing or unsealed spherical bearing alone, we selected an oversized sealed greaseable spherical monoball to offer unparalleled durability and precision, but designed a Delrin® adapter sleeve to help isolate the added noise, vibration, and harshness that a full solid monoball bearing will have. While race-ready, our hybrid Delrin®/monoball control arm bearings are more at home on the street than other kits that are advertised as “race-only” bearings. We did extensive street, autocross, and track testing to ensure the spherical bearing used in this bushing design excelled in each setting.

The stock rubber bushings, even those found in the M3, allow significant fore/aft movement of the front wheels to help absorb road impacts, especially when being pushed hard.  This soft flexible design maximizes daily driving comfort, but also allows considerable alignment change.  This unwanted deflection stands between you and a crisp, confidence-inspiring driving experience.  The advantage of a monoball bearing is that it will not deflect under load, eliminating all unwanted deflection while still allowing complete freedom of movement in the desired angles. What you get is superior steering precision with better handling from more consistent alignment and direct braking feedback, with exceptional service life.  Thanks to the Delrin® insert and double lip seals, there's none of the extra noise or reduced service life often found on other spherical bearings.

In short, if you're seeking front control arm bushings that offer precise, predictable handling, crisper braking feel, with a long service life free from noise - look no further. We have you covered.

Watch to learn more about Turner Monoball Bushings

Features:

Bearing housing

• Precision CNC machined from 6061-T6 blue anodized aluminum with a pre-installed grease fitting and grease distribution channels making this a serviceable design
• Knurling allows for a wide variance in lollipop dimension, although this particular SKU comes pre-installed, so you won't need to worry about that. Want to install your own? Click here. 

Bearing

• A high quality sealed bearing with Delrin® inserts. Delrin® was chosen due to durability under pressure, while still soft enough to create a perfect play-free fitment on the control arm.
• Replaceable for infinite service life - no need to replace the entire mount in the event a bearing happens to fail.

Includes new hardware. Grease before installation and with each oil service with high quality Moly grease for maximum service life. Need a grease fitting tool?

Installation is relatively easy - see our instructions here.

This item fits the following BMWs that use a centered-style bushing: 

1984-1991 E30 BMW 318i, 318is, 325, 325e, 325es, 325i, 325is 
1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic
1996-1999 E36 BMW M3 S52
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i MZ3 M Coupe M Roadster 

Here at Turner we understand the importance of an upgrade that will get the results you need on the track and still be tolerable on the drive around town. When it comes to control arms on the track, making them as stiff as you can (usually using solid mounts) is the best way to increase your driving precision by eliminating the deflection of rubber. The next best thing to create a balance would be to stiffen up the control arm with polyurethane, giving you the option of a more stock like feel with 80a or closer to the solid feel with 95a durometers.

When it comes to the E36 chassis you also get the options of choosing a stock centered design or going with the E30 inspired offset bushing to increase castor, further taking advantage of improvd handling. These poly bushings will give your control arms a direct connection between your suspension and the body of the car eliminating the slop felt under take-off and braking so you feel more in control of your vehicle. 

This item fits the following BMWs that use a centered-style bushing: 

1984-1991 E30 BMW 318i, 318is, 325, 325e, 325es, 325i, 325is 
1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic
1996-1999 E36 BMW M3 S52
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i MZ3 M Coupe M Roadster 

When we designed this catch we wanted to have the most function options available, the best separation method, and the easiest to service. The Turner engineered catch cans offer a pre-setup design based ion desired flow direction, however this does not limit you to this flow. The inner baffle orientation can be easily adjusted to flow in both directions in case you decide to move this catch can to a different vehicle. A 4 chamber system  baffle system inside the catch can was engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can. Having a closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation.

Our catch can was also designed with the idea that the cans fill level can easily be checked with a top mounted dipstick and an optional use bottom drain hole. The drain hole can be used with a valve and hose to be mounted at a lower area of the vehicle so when you're doing an oil change you can drain the catch can.

Features:

• 6061-T6 billet machined body, anodized black for lasting protection and appearance
• Strategically positioned 4 chamber baffle system maximizes oil / air separation 
• Knurled and black anodized oil dipstick makes inspecting oil volume of reservoir clean and simple
• Sealed with a pre-installed viton O-Ring
• Includes 2.5mm allen key to remove baffle plates for cleaning
• Engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can
• Closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation
• Optional use drain hole (valve and hose sold separately, watch for our model specific drain kits!)

BMW M50 S50 S52 Turner Motorsport Power Pulley Kit: Boost Your BMW's Performance

• Increases horsepower and torque
• Improves throttle response and acceleration
• Lightweight design reduces rotating mass
• Precision-engineered for perfect fitment

Upgrade your BMW's performance with the BMW M50 S50 S52 Turner Motorsport Power Pulley Kit. This kit is designed to increase horsepower and torque by reducing the rotational mass of the engine's accessories. With improved throttle response and acceleration, you'll experience a more dynamic driving experience. The lightweight design of the pulleys reduces rotating mass, resulting in improved engine efficiency. Plus, each pulley is precision-engineered for perfect fitment, ensuring seamless integration with your BMW's engine.

Turner has developed a proprietary zinc-nickel plating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

Upgrade your engine build with Turner's WPC-treated Race Series Bearings, engineered for serious performance enthusiasts. Starting with ACL’s high-performance bearing shells, these Race Series bearings are built to withstand extreme RPMs and stress. Utilizing a "Duraglide" tri-metal construction and a high-strength overlay plate, these bearings offer superior oiling and heat resistance for high-RPM operation.

Our WPC-treated bearings take ACL’s already impressive design and enhance it even further. The WPC treatment process strengthens and smooths the bearing surface by firing high-speed, ultra-fine particles at the bearing shells, reducing friction and improving durability. This advanced surface treatment ensures smoother operation and improved heat dissipation, which are critical for any high-performance engine.

Key Features:

Duraglide Tri-Metal Construction: ACL's Race Series bearings feature a high-strength overlay for enhanced performance. Optimized Oiling: Designed to promote better oil flow during high-RPM conditions. Precise Fitment: Manufactured with OEM-level precision using micron tolerance machining. WPC-Treated for Strength: Surface treatment adds strength and reduces friction for improved engine performance. No Flash Plating: Allows for better heat transfer and bearing retention. Thermal Discharge Process: Smoother, stronger components through WPC’s unique thermal discharge technology. Enhanced Heat and Friction Resistance: Built to combat the biggest enemies of high-performance engines. Don’t settle for standard bearings—choose Turner Motorsport WPC-treated Race Series Bearings for the ultimate engine performance upgrade. Perfect for your next engine rebuild or main bearing service!

Here at Turner we understand the importance of an upgrade that will get the results you need on the track and still be tolerable on the drive around town. When it comes to control arms on the track, making them as stiff as you can (usually using solid mounts) is the best way to increase your driving precision by eliminating the deflection of rubber. The next best thing to create a balance would be to stiffen up the control arm with polyurethane, giving you the option of a more stock like feel with 80a or closer to the solid feel with 95a durometers.

When it comes to the E36 chassis you also get the options of choosing a stock centered design or going with the E30 inspired offset bushing to increase castor, further taking advantage of improvd handling. These poly bushings will give your control arms a direct connection between your suspension and the body of the car eliminating the slop felt under take-off and braking so you feel more in control of your vehicle.

This item fits the following BMWs that use a centered-style bushing: 

1984-1991 E30 BMW 318i, 318is, 325, 325e, 325es, 325i, 325is 
1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic
1996-1999 E36 BMW M3 S50 S52
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i MZ3 M Coupe M Roadster 

Set of 2 universal 2.5" inlet to 4.0" outlet exhaust tips.

Over the years, it is not uncommon for exhaust tips to be damaged and corroded, becoming a "sore spot" of your BMW. To remedy this unsightly feature, we now offer our very own exhaust tips! Featuring stainless steel construction and a simple, yet sporty design, this exhaust tip will look perfectly at home on almost any model.

Features & Specifications:

Swivel feature for perfect alignment of the exhaust tips in the rear bumper
2.5" Inner Diameter
4.0" Outer Diameter
Black Chrome
Double Wall Construction
Angle Cut Style
Includes Stainless Steel Clamp

The factory VANOS exhaust hub on the S54 engine is known to develop excessive play where the drive tabs interface with the oil pump disk. Over time, this imprecise fitment causes a back-and-forth rattling motion that can result in the tabs shearing off inside the engine, risking catastrophic damage or complete engine failure. Unlike other aftermarket solutions that require full VANOS disassembly, retiming, or replacement of the oil pump disk, the Turner Motorsport S54 VANOS Hub Upgrade offers a smarter approach. Our bolt-on fix eliminates the common failure point without opening the VANOS unit or disturbing engine timing.

Our solution involves removing the worn tabs from your stock exhaust hub and installing our precision-fit replacement, which is precision-machined from 4340 steel and hardened to meet OEM specifications. Designed using 3D scanning and CAD modeling, the Turner Motorsport VANOS Exhaust Hub Upgrade provides a tight, interference-free fit into the oil pump disc, completely resolving the issue without unnecessary labor.

Features & Benefits:

Direct bolt-on solution for S54 VANOS oil pump drive tab failure, preventing potentially catastrophic damage to engine internals Precision-machined from high-strength 4340 steel and heat-treated to match OEM specifications Designed using 3D scanning and CAD modeling to ensure precise fitment within the OEM oil pump disc Engineered to eliminate the play that exists between the exhaust hub and oil pump disc from factory Backed by extensive real-world testing and our lifetime replacement program!

A combination of billet fittings and AN lines for an upgraded and serviceable crankcase vent hose. Attaches between the oil separator and the CSL air box.

The factory rubber/plastic hoses become brittle and crack over time. Brittle and cracked hoses can cause multiple vacuum leaks that are impossible to repair without hose replacement. Vacuum leaks can cause many problems including rough running, missing, stalling at idle, and even a no-start condition. The factory hoses offered through BMW are plastic and will yield the same results of becoming brittle and damaged over time.

We have created a full motorsport style solution with our CSL Crankcase made from machined 6061 billet aluminum with AN style fittings and nylon fiber braided lines. This is a fully serviceable replacement that will outlast every one of the OEM replacements. Our AN crankcase line can be used to replace the factory brittle hose to ensure your S54 is free from vacuum leaks and performing properly.

OEM CSL Vent Hose (11157833649) - Direct Replacement

Key benefits:

Lifetime replacement of the brittle OEM plastic crankcase breather hose
Fully Serviceable
Motorsport Aesthetic to compliment your CSL Intake Plenum
Design:

Fittings are made from billet 6061-T6 aluminum and finished in Type II black anodizing
Pre-anodized machined Turner branding
Nylon fiber braided lines
Fittings are a direct replacement for the plastic OEM fittings

Over the years, it is not uncommon for exhaust tips to be damaged and corroded, becoming a "sore spot" of your BMW. To remedy this unsightly feature, we now offer our very own exhaust tips! Featuring stainless steel construction and a simple, yet sporty design, this exhaust tip will look perfectly at home on almost any model.

Features & Specifications:

3.0" Inner Diameter
4.0" Outer Diameter
Brushed Finish
Double Wall Construction
Slant Cut Style
Includes Stainless Steel Clamp