**Not to be used with Liqui Moly Molygen Engine Oil - Molygen already includes friction modifiers**
Step 1 - Engine Flush - Add to engine oil before engine oil change. Let engine run on idle speed for 10 minutes. Drain oil, change oil filter and re-fill with fresh high quality oil.
Pro-Line Engine Flush is a development product based on highly effective state-of-the-art additive technology. These highly effective detergent and dispersant additives, in association with the carrier fluid, have been tested in the laboratory and in practical field trials for their ability to dissolve sludge and lacquer formers. All types of oil-soluble and oil-insoluble residues are brought into suspension and removed during the next oil change. An engine which has been cleaned of deposits and contamination and which is then filled with fresh oil not contaminated with old impurities can develop its full performance characteristics.
Properties:
Gentle and rapid cleaning
Neutral to seals and other materials installed in the engine
Compatible with catalytic converters
Highly economical
No additional environmental pollution
Simple to use
Contents sufficient for 5 liter engine oil capacity
Fully compatible with all commercially available engine oils.
Benefits:
Removes deposits & residues
Dissolves sludge & lacquer and isolates solid particles & liquid contaminants
Improves the combustion process and restores full engine performance
Prevents corrosion of unprotected metal surfaces
Recovers oil lubricating properties
Suitable for all gasoline and diesel engines.
Step 2 - Cera Tec - Add in with your New Engine Oil
Cera Tec is a high quality ceramic wear protection product which is safe for use in all engine oils. It reduces friction and wear due to ceramic compounds that withstand extremely high chemical and thermal loads. Cera Tec reduces direct metal-to-metal contact, thus increasing the engine service life. The low-friction effect reduces fuel consumption in gasoline and diesel engines. The chemicals in this specially-formulated product adhere to metal surfaces to reduce internal wear and friction, giving you peace-of-mind and saving you costly repairs in the future. Treats up to 5 liters of engine oil and provides up to 30,000 miles of protection under normal driving conditions.
*Note: Not suitable for use with wet clutch applications or limited slip differentials. Great for use in vehicles with high-pressure, cam-driven fuel pumps or engines making noise upon start-up.
**Not to be used with Liqui Moly Molygen Engine Oil - Molygen already includes friction modifiers**
Step 1 - Engine Flush - Add to engine oil before engine oil change. Let engine run on idle speed for 10 minutes. Drain oil, change oil filter and re-fill with fresh high quality oil.
Pro-Line Engine Flush is a development product based on highly effective state-of-the-art additive technology. These highly effective detergent and dispersant additives, in association with the carrier fluid, have been tested in the laboratory and in practical field trials for their ability to dissolve sludge and lacquer formers. All types of oil-soluble and oil-insoluble residues are brought into suspension and removed during the next oil change. An engine which has been cleaned of deposits and contamination and which is then filled with fresh oil not contaminated with old impurities can develop its full performance characteristics.
Properties:
Gentle and rapid cleaning
Neutral to seals and other materials installed in the engine
Compatible with catalytic converters
Highly economical
No additional environmental pollution
Simple to use
Contents sufficient for 5 liter engine oil capacity
Fully compatible with all commercially available engine oils.
Improves the combustion process and restores full engine performance
Prevents corrosion of unprotected metal surfaces
Recovers oil lubricating properties
Suitable for all gasoline and diesel engines.
Step 2 - Cera Tec - Add in with your New Engine Oil
Cera Tec is a high quality ceramic wear protection product which is safe for use in all engine oils. It reduces friction and wear due to ceramic compounds that withstand extremely high chemical and thermal loads. Cera Tec reduces direct metal-to-metal contact, thus increasing the engine service life. The low-friction effect reduces fuel consumption in gasoline and diesel engines. The chemicals in this specially-formulated product adhere to metal surfaces to reduce internal wear and friction, giving you peace-of-mind and saving you costly repairs in the future. Treats up to 5 liters of engine oil and provides up to 30,000 miles of protection under normal driving conditions.
*Note: Not suitable for use with wet clutch applications or limited slip differentials. Great for use in vehicles with high-pressure, cam-driven fuel pumps or engines making noise upon start-up.
This product is not eligible for Lifetime Replacement
Fits These Cars
MAKE
MODEL
SUBMODEL
ENGINE
Special Fitment Notes
BMW
All
All
All
Use vehicle selector to confirm fitment
MINI
All
All
All
Use vehicle selector to confirm fitment
*The above product applications have been written by Turner Motorsport. All
warranties, product application, fitment, and performance are the responsibility of Turner Motorsport.
For additional information see the terms of use.
Prop 65 Warning
