BMW Tools & Specialty Equipment for BMW E12 530i M30 3.0L

Protect your finish when working under the hood with a high quality Turner fender cover. Made from a synthetic leather layer with a goose flannelette backing for durability and protection. The Turner fender cover holds a tight grip to your fender or core support with four 9.5" magnets sewn into the top layer.

Features:

• Durable synthetic leather with the Turner logo
• Soft goose flannelette backing
• Four 9.5" integrated magnets

Dimensions:

•  Extra Long 20" x 47"

Proper torque is very important when it comes to working on engines. The importance comes from proper sealing and to keep from damaging threads.

Features:

• Reversible ½-inch drive click-to-stop
• Torque range of 10 to 150 ft-lb
• Accurate to within +/-4%
• 18 inches in length with a convenient carry case

Our aluminum wheel hanger makes it easy to remove and install wheels. Just thread the hanger stud into a wheel bolt hole and hang the wheel safely while you rotate tires or remove them for service or vehicle repair. (It's also great for keeping wheel bolt holes aligned on cars with spacers.)

Features:

• Longer & Lighter
• Made of 6061-T6 aluminum
• Anodized for hardness and good looks
• Knurled, non-slip handle has a drilled hole so you can hang it on a pegboard hook in your garage

Better still, order two: one for your garage and another for the emergency tool kit in you trunk.

Tired of busting your knuckles from old hardened exhaust hangers?

This Schwaben tool removes the hanger by pressing on the steel hanger bracket and pulling the rubber hanger in one motion. Self centering force pin locks onto the pin while the flat paddle pulls off the rubber hanger from behind. Slim profile and a 25 degree offset works in tight areas.

Safety is always the most important factor when it comes to working under your car, jack stands are highly recommended. 

Features:

• Ultra light  jack stands only weigh 4.7 lbs each
• All aluminum construction with heavy-duty  flanged bases to safely stabilize loads
• 6 locking positions for a secure load in multiple heights
• Extra heavy duty load pin at .584 in. diameter with a posi lock ball to insure it stays in place
• Min. Height is 10.6
• Max Height is 15.4"
• Large 7" diameter base
• Outer support tube is 2-1/8" in diameter

This large socket is the perfect tool for axle nuts when servicing the axle shafts or wheel bearings.

Features:

• ½-inch drive 46mm 12-point socket
• Specially hardened to take the added abuse from a impact gun
• Coated for added protection and so you can tell it apart from non impact rated sockets
• 75mm depth  to accommodate many applications and different length shafts
• Made of durable chrome moly steel

These weld protectors allow you to safely jack up your vehicle without crushing or bending any pinch welds. These will fit any jack and will work with many jack stands such as the Schwaben Aluminum Jack Stands.

Specifications:

• 3" wide
• 1" tall
• Single groove top
• Double grooved bottom

Custom exhaust work in the plans? The Schwaben Exhaust Pipe Cutter will help you cut out old pipe or cut down new pipe with ease. It can cut any pipes from 3/4" to 3" in diameter and cuts pipe with only 1/4 turn adjustments, thanks to 15 blades that effectively cut the entire pipe with little movement. This is great for tight to reach places that prevents you from using more traditional non-specialty tools.

Features:

• Cuts from 3/4" pipe up to 3" pipe
• 15 cutting blades
• Rubber covered handles for grip and comfort

This complete set of extra deep sockets work great on cars equipped with extended studs. They also work as a long wheel nut socket for those deeply recessed nuts in wheels.

Features:

• 17mm, 19mm and 21mm socket in a sturdy blow molded case
• All sockets are 1/2" drive and a full 5-15/16 ( 150MM ) long
• Sockets are designed with inner bore to accept a 5" long stud

The Schwaben Dual Temperature Heat Gun Kit is the ideal tool for stripping paint, removing decals, shrinking wire wrap, etc. The heat gun has a switch which allows for two different heat settings (572F and 932F).

Features:

Four airflow adapters, 1pc Large Deflector Nozzle, 1pc Reduction Nozzle, 1pc Small Deflector Nozzle, and 1pc Reflector Nozzle.
Voltage 120C, 60 HZ
Amps 12.5A
Two heat settings: Low Heat up to 572 Degree F. High Heat 932 Degree F.
Air Volume: Low Heat: 10 cfm (280L/min) High Heat: 17 cfm (480 L/min)
Wattage: Low Heat: 1000W High Heat: 1500W
Has 6.75 Ft cord.
Built in hook to hang on wall.
For California Prop 65 warning see: www.P65Warnings.ca.gov. and photo below.

Wall Hangers Set is the ideal solution for organizing and storing QuickJack frames in a garage. Designed for those who prefer a clean and efficient storage solution, these hangers provide a convenient way to keep your portable car lift frames off the ground and out of the way. The hangers mount directly into a sturdy wall stud, ensuring safe and simple storage for all QuickJack models. Each mount is crafted with a sleek, laser-cut QuickJack logo, affirming its authenticity and quality.

• Secure storage: Mounts directly into wall studs for safe and stable hanging of QuickJack frames.
• Universal fit: Accommodates all QuickJack models, ensuring versatility and convenience.
• Durable construction: Over-engineered to 150% of the rated capacity for long-lasting durability.
• High-quality materials: Made from brushed steel for a robust and stylish appearance.
• Authentic design: Features a sleek, laser-cut QuickJack logo, reflecting its official status and rigorous engineering standards.
• Easy installation: Simple to install, with real-world testing and advanced computer analysis ensuring reliability and resilience.

Upgrade your garage organization with the Wall Hangers Set for a neat, secure, and professional storage solution for your QuickJack frames.

A professional quality flex ratchet features a fine satin finish designed for durability and easy clean up.

Features:

• Special designed 72T gear mechanism
• 5 degree of handle movement between gears 
• Flex head has 7 detent positions in a 180 degree swing
• Push button release holds socket tight until you are ready to release
• Ratchet is a full 290mm ( 11") long for extra leverage.

Limited Lifetime Warranty