BMW Engine Parts for BMW 5 Series E34 (1987-1995)

Introducing the ACL Race Series High-Performance Main Bearing Set, meticulously crafted for BMW enthusiasts running M20, M50, M52, M54, S50, S52, and S54 engines. Take your BMW’s engine durability and performance to the next level with these race-proven main bearings, designed to handle the demands of aggressive driving and high-RPM scenarios.

Built with ACL’s Duraglide tri-metal technology, this main bearing set ensures exceptional oil flow and resistance to wear, even in extreme conditions. Engineered for performance, this upgrade is a direct replacement for stock BMW main bearings, providing enhanced strength and longevity without compromising factory tolerances.

Key Features:

Race-proven design: Ideal for performance builds, this complete set delivers superior oiling and heat resistance, making it perfect for high-RPM use. Precision fitment: Engineered specifically for BMW’s M and S series engines, offering a reliable solution for common crankshaft bearing wear issues. Duraglide technology: Featuring tri-metal construction, including a copper-lead base and high-strength overlay, for improved oil retention and reduced friction. High-load capacity: Designed to withstand the rigors of spirited driving and competition, preventing distortion and wear during peak performance. Optimized for high performance: Eliminates tin flash plating, allowing for better bearing-to-housing contact and improved durability under extreme pressure. Whether you're rebuilding your BMW for the track or simply want to ensure reliable performance under demanding conditions, the ACL Race Series Main Bearing Set offers the perfect upgrade solution. Boost your engine’s reliability and extend its lifespan with this high-performance bearing set.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their exacting assembly process and high level of durability you can expect a long service life from all Bosch products.

This genuine Bosch Starter motor fits the following BMWs:
1987-1991 E30 3 Series 325i 325is 325ix 325ic
1989-1987-1988 E30 3 Series 325e 325es 12/1986-1988
1989-1990 E34 5 Series 525i M20 engine only
1987-1988 E28 5 Series 528e 12/1986-1988

Includes $45 core charge to be refunded on return of your rebuildable core.

These WPC-treated bearings are the best we have seen! WPC is a shot-peening treatment at a microscopic level. It's perfect for sensitive surfaces like bearings. The WPC treatment removes imperfections and high spots, while creating a surface that retains oil better than the original surface. This greatly reduces friction. The bearings in this kit are original equipment KS bearings that are sent to WPC for treatment. The treated bearings are stronger with less metal fatigue and less friction than buying off-the-shelf bearings from the dealer.

This item fits the following BMWs: 
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is 325ix 
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
1982-1988 E28 BMW 528e
1989-1995 E34 BMW 525i
1997-2003 E39 BMW 525i 528i 530i
2004-2005 E60 BMW 525i 530i 
2004-2006 E83 BMW X3 2.5i X3 3.0i 
2000-2006 E53 BMW X5 3.0i 
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe 
2003-2005 Z4 BMW Z4 2.5i Z4 3.0i 

The Schwaben Piston Ring Filer is a vital tool for obtaining the precise end gap necessary for optimal piston ring performance.

This filer allows you to swiftly and accurately file piston rings to exact measurements, enhancing your engine’s efficiency and lifespan. By simply positioning the piston ring and turning the handle, you can easily rotate the abrasive wheel for a smooth and effective filing process.

**Note:** For the Schwaben Universal Piston Ring Compressor, check out T25805755!

Key Features:

• Optimize Performance: Achieve the perfect end gap crucial for top engine efficiency.
• Quick and Precise: File rings to exact specifications with ease.
• Easy Operation: Position the piston ring and turn the handle to effortlessly rotate the abrasive wheel.
• Enhanced Engine Longevity: Accurate end gaps contribute to longer engine life and better performance.

Instructions:

1. Position the Ring: Place the piston ring on the outer edge against the stop and align the ends squarely against the grinding wheel. Apply light, even pressure against the wheel to prevent grinding too large a gap.
2. Operate the Tool: Turn the handle so the grinding wheel turns towards the inside edge of the ring (counter-clockwise when viewed from the handle side of the tool).
3. Exercise Caution: This is a diamond grinding wheel. It cuts fast!

Checking Piston Ring Gap:

1. Deburr the Ring Ends: Carefully remove any burrs on the ring ends before placing the ring in the bore. A light touch with a fine abrasive stone works well.
2. Clean the Rings: Thoroughly clean the rings with lacquer thinner or acetone, as the paint coating from the factory may occasionally scratch the cylinder bore. Always wear gloves during this process.
3. Position the Ring in the Cylinder: Place the ring squarely in the cylinder bore, about 1" down from the deck surface. An upside-down flat-top piston will help you properly square the ring.
4. Measure the End Gap: Use a feeler gauge to measure the ring's end gap. Apply light grinding pressure and check frequently to avoid making the end gap too large.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

For optimal valve train performance in your BMW, replace old rockers when shaft/rocker clearance exceeds specifications. When installing a new cam or rocker shafts, it's recommended to re-machine rocker pads or replace rockers to ensure maximum valve train life. The kit includes rockers and provides benefits such as:

• Replacement for old rockers with excessive clearance.
• Ensures maximum valve train life with new cam or rocker shaft installation.
• Rocker bushings may need honing for proper clearance.
• Careful inspection of rocker shafts for even wear and replacement if necessary.
• Avoid installing new rockers with a worn camshaft to extend service life.
• Comprehensive kit for valve train maintenance in BMW engines.

This is the Genuine BMW timing chain tensioner for BMW's with the M60 or M62 V8 engines.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

This item fits the following BMWs:
1993-1995 E34 BMW 530i 540i
1997-2003 E39 BMW 540i
1988-1994 E32 BMW 740i 740il
1995-2001 E38 BMW 740i 740il
1990-1999 E31 BMW 840i 840ci
2000-2003 E53 BMW X5 4.4i X5 4.6is
2000-2003 E52 BMW Z8 Alpina Roadster

The intermediate shaft bearings are located in the engine block (an inner and outer bearing). The intermediate shaft is driven from the timing belt and spins the oil pump shaft. Whenever the engine is torn down and the block is chemically or thermally cleaned these bearings will need to be replaced. The bearings must be sized with the intermediate shaft! The bearing surfaces must be machined to the correct tolerance for the block and shaft! You must make your engine builder aware of this before final assembly.

Note: these bearings must be machined for the shaft and block.

M20 block uses inner and outer bearings but the bearings are the same part numbers.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

If you are experiencing misfires or rough idle issues, the cause could be a failing ignition coil. Bosch Ignition Coils are the perfect OEM replacement to restore perfect operation to your ignition system.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

For the following BMW engines: M42 M60 M62 M50 S50