Select Vehicle
BMW
Mini
Create an account to be able to build Wish Lists.
Please ensure your correct model is selected
Give your factory clutch a heavier motorsport feel or make your extremely tough clutch more drivable! If you have an E36 there is absolutely no reason you don't have this clutch pedal! Your factory E36 clutch pedal is made of flimsy plastic with no adjustment at all, leaving you to the mercy of the clutch you have.
Our Turner Performance Adjustable Clutch Pedal is a rigid design that gives you the ability to fully adjust your clutch feel and performance. With both upper and lower adjustments this is the best pedal on the market to fine tune your clutch pedal just the way you like it. The upper eccentric provides an adjustable pedal ratio to fine tune clutch pedal effort(how heavy the pedal feels). The lower adjustment is to change the position of the clutch assist spring, this allows you to choose where the clutch assisting spring engages. Changing where the spring engages will move the area of tension on your clutch from lower, middle to higher for maximum adjustment.
Your race car no longer needs to have a clutch that makes the car undriveable on the street. Your track car can now be your daily driver or weekend cruiser.
Features:
Adjustable throw
Capable of quicker shifts
Three lower mounting points for the spring to adjust where the assistance engages
Eccentric mount for master cylinder to adjust leverage ratio and pedal feel(weight/force needed to engage the clutch)
Self lubricating bronze bushings
All necessary hardware required for installation
Pedal body and pedal are constructed from 6061-T6 aluminum and type II black anodized for a great finish
NOTE: This Clutch Pedal does not include the Compression spring and the original spring must be reused. If you'd like to purchase a new spring, please see:
35311162505 - Non-M E36 - T#64615
21522227764 - E36 M3 - T#21753
The ULTIMATE shifter upgrade for your BMW! Experience more precise throws, less shift lever travel, and an all-around transformation in your shifting experience.
For dozens of years, enthusiasts have critiqued the imprecise and vague feeling of BMW manual transmissions. Plagued with long throws, fore and aft play in gear, and a generally loose feeling, your OEM BMW shifter leaves much to be desired. While most standard carrier-mount short throw shifter kits will aid in reducing throw length and eliminating side-to-side play in gear, some enthusiasts long for a hardcore, race-inspired shifter that completely removes play and excessive throw length. At Turner Motorsport we share the same desire and set out to offer the ULTIMATE upgrade with this Performance Chassis Mount Short Shifter.
WHY UPGRADE?
Factory BMW shifter assemblies are complex by nature. The main component of this assembly is the shift carrier, a cast aluminum piece positioned inside the transmission tunnel that incorporates bushings at both ends for mounting. Like most factory parts, these bushings are designed to reduce NVH (noise, vibration, and harshness) transmission to the cabin. To the spirited driver, however, these bushings translate to flex and vagueness in the shift lever. Moreover, because this carrier is mounted to both the transmission and the body, the entire shifter assembly will "float" with the driveline, further increasing the vague and imprecise feeling of your shifter.
Our Performance Chassis Mount Short Shifter removes the shift carrier assembly entirely—removing any prospect of flex caused by bushings or driveline movement. By contrast, this chassis mount shifter offers a drastic reduction in shift lever travel, vagueness, and side-to-side play. An elevated base allows for moving the fulcrum point upwards, resulting in a much shorter and more precise throw. Shift times are further reduced by a tall, "rally style" shift lever, used to aid in leverage while also bringing the lever closer to the steering wheel. Our design incorporates a proprietary centering spring design, which is adjustable for increasing or decreasing self-centering force. In short, this design eliminates all the drawbacks of your factory BMW shifter, translating to more control, greater precision, shorter throws, and faster shift times.
FEATURES & BENEFITS
Reduced Throw: Modified shifter geometry and heightened fulcrum point translate to a shorter shift lever throw
Improved Shifter Feel: Eliminating the shift carrier and associated bushings drastically reduces "slop" and side-to-side play in the shift lever
Increased Precision: Mounting the shifter to the chassis allows for little to no variation in gear selection
Universal Fitment: Fits many BMW chassis with the provided base plate and hardware (see "Fits These Cars" for exact fitment information)
DESIGN
6061 aluminum, 4130 steel, and 316 stainless steel construction
A type-II black anodized finish
Adjustable self-centering spring
"Rally Style" shift lever
Spherical bearing pivot with maintenance-free brass insert
Product Development:
Our Chassis Mount Shifters are designed, engineered, tested and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer and rigorous long term product testing.
If allowed in the rules these solid aluminum transmission mounts offer many advantages over a urethane or Delrin mounts. It's no wonder that these mounts have found their way into the top BMW racers in the country. These are machined from solid aluminum and have zero deflection, engine torque will cause a rubber or urethane mount to flex or deflect allowing more torque to passed through the drive line (instead of being wasted winding up the mount). This puts the shift linkages in better consistent alignment. And unlike rubber or urethane the aluminum has zero wear and is not affected by leaking oil or other fluids so this is likely the last set of transmission mounts you will ever need. We very strongly recommend using the solid transmission and engine mounts together as a complete kit, mixing a rubber mount with a metal mount will cause undue stress on the mounting points and will lead to a failure. We never advise using a solid mount unless a corresponding solid mount is also used.
These are a no-compromise design for all-out racing use, full solid aluminum mounts should not be used on street-driven cars since there is no material to absorb vibration making these quite harsh for regular street use (track cars don't care about noise).
Product features and benefits:
This item fits the following BMWs:
1989-1995 E34 BMW 525i 530i 535i 540i M5
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1997-2003 E39 BMW 525i 528i 530i 540i M5
1999-2005 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci M3
2008-2012 E82 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
Sometimes choosing the correct shift kit proves difficult when you dual-purpose your favorite vehicle, we understand this well. The early days for any race enthusiast usually begins with a car that is needed to daily drive and setup to get out on the track. What becomes difficult is properly modifying that car to feel comfortable in both situations which is why we took this view on our new short shift line. This upgraded lever is a quick swap option to replace the standard shift lever that come with our kits so you can keep your hands closer to the wheel while shifting at high speeds. Designed from anodized aluminum this lever looks great in any interior for the daily driver who simply prefers the taller lever look and feel.
NOTE THAT THESE ARE DESIGNED TO WORK WITH TURNER MOTORSPORT SHORT SHIFTERS ONLY - We wanted to give you the option to buy one separately, in case you changed your mind after buying our short shifter.
Features:
Compatible with stock shift boot fits nicely into the machined groove at the bottom of the lever to maintain a clean look in the interior.
Machined from 6061-T6 aluminum and type II anodized for exceptional durability and corrosion resistance.
Available in either black or clear anodize to match your vehicle’s interior.
Rally shift knob is machined from black delrin.
Unlike aluminum, delrin will not hold heat so on those hot days you won’t have to worry about burning your hand on a knob that’s been baking in the sun.
Shift knob is threaded onto the end of the shift lever utilizing a standard ⅜-16 thread to allow for easy removal and attachment of your favorite beer tap or other accessory.
“Quick Change” height adjustable upper shift lever design allows for quick swapping between optional “OE” style and “Rally Style” upper shift levers.
22mm adjustment range to fine tune shifter throw and feel.
If allowed in the rules these solid aluminum engine and transmission mounts offer many advantages over a urethane or Delrin mounts. It's no wonder that these mounts have found their way into the top BMW racers in the country. We originally developed these mounts for E36 and E46 World Challenge racing but they also work perfect in BMW Modified and SCCA club racing and SpecE46 (SE46). These are machined from solid aluminum and have zero deflection. The engine torque will cause a rubber or urethane mount to flex or deflect. The stiffer the material the less movement there is and the more torque is passed through the driveline (instead of being wasted winding up the mount). At the transmission end the flex-free solid mounts will give smoother, crisper shifts since the transmission is no longer dancing on the pliable mount. This puts the shift linkages in better consistent alignment. And unlike rubber or urethane the aluminum has zero wear and is not affected by leaking oil or other fluids so this is likely the last set of motor and transmission mounts you will ever need. We have designed these mounts so the engine is 5mm lower and the transmission is 1mm lower than the factory mounts. This helps lower the center of gravity for better balance and handling. We very strongly recommend using the transmission and engine mounts together as a complete kit. Mixing a rubber mount with a metal mount will cause undue stress on the mouting points and will lead to a failure. We never advise using a solid mount unless a corresponding solid mount is also used. This kit fits the E36, E46, Z3, and Z4 6 cylinder models listed below, including M3 models.
Single piece 6061 construction, optimized cooling, provisions for temp sensor, and external cooler with removable air duct.
Built to last, made from a single piece of 6061 billet aluminum with a rugged and good-looking hard-coat anodizing our diff cover can handle anything you throw at it. Not only is it an absolute masterpiece to look at but the billet diff cover checks all the boxes for features needed. Reinforced mounting ears for strength and stability, never again will you break an ear off your diff cover like the factory units are known to do. Each ear is not only unified with the one-piece billet cover but also feature added material for the highest durability possible. This diff cover is cool, literally, the entire construction was designed with optimized cooling in mind. External fins are strategically placed on the rear face, bottom, and between the mounting ears of the cover, serving as effective heat sinks for optimal heat dissipation. This ensures stable temperatures, promoting longevity for both the fluid and your differential. Additionally, the internal design ensures continuous oiling and lubrication to the ring gear, maintaining its stability and preventing fatigue by controlling heat more effectively. An internal baffle at the cover's corner helps maintain proper pressure and prevents cavitation.
All of the OEM features were retained along with the upgrades. The mounting surface was designed to be compatible with both the OEM gasket or RTV of your choosing, some people don't trust the gaskets and we get it. You can transfer your speed sensor directly to your upgraded billet cover and it even features a provision for the sensor wire mounting. Factory bushing geometry allows you to use any E36 diff busing including rubber, poly, and even solid mounts. The drain and fill plugs on the diff cover are upgraded to -6AN using the provided high-pressure fittings with replaceable o-rings. The drain and fill plugs can now also be used for expanding to an external oil cooler allowing you to further expand the fluid capacity for optimized cooling and service intervals. To keep an eye on things from the driver seat is 1/8 NPT provision for temp sensors, this product from Turner has you covered at every turn.
Why the upgrade?
If you're new to differential covers used in earlier generations like the E30, you'll find significant improvements in the OEM E36 cover. Unlike the E30's single mount design, the E36 features a dual mount design, which was introduced to address common issues such as broken mounts due to worn-out bushings and aggressive driving. This upgrade significantly enhanced durability and reliability.
While the factory E36 differential cover was a significant improvement with its dual mounts compared to the previous generation, there are still some shortcomings that the original cover doesn't address. Most factory differential covers, including those on the E36, are cast from aluminum. However, due to the porous nature of cast aluminum, the mounting ears on these covers cannot withstand the intense shocks typical in motorsport or in vehicles with significantly increased power.
Upgrading to our Reinforced Billet Differential cover gives you the strength you need to push your car to its limits without worrying about snapping a diff mount from clutch kicking or other shocks to the drivetrain. In addition to its enhanced strength, this differential cover includes numerous other upgrades and conveniences. These include improved cooling and lubrication for the ring gear, upgraded fill and drain plugs, and the option to expand an external oil cooler for extreme motorsport usage. Designed to complement both upgraded daily drivers and extensively modified track cars, it also boasts a visually appealing design.
Key Benefits:
Reinforced mounting ears for strength and stability - never again will you break an ear off during an aggressive drive or track event
External fins on the back side, bottom, and mounting ears on the casing for maximum cooling and consistent fluid temps
Removeable air duct to direct air across the cooling fins for even more temperature control
Optimized internal design to keep fluid consistently on the ring gear
Integrated breather to prevent cavitation by venting the appropriate amount of pressure being built up in the diff housing
-6AN ports to incorporate the use of a differential cooler - this increases capacity and lowers temps allowing for extended fluid change intervals
1/8 NPT fitting for the use of a temp sensor to monitor fluid temperature
Design:
Single piece 6061 Billet aluminum construction
T6 Black hard coat anodizing for superior corrosion resistance and aesthetics
Compatible with most differential coolers(-6AN) and temp sensors(1/8 NPT)
Designed to accommodate oversized rear sway bars
Retains OEM mounting features including the use of the OEM gasket
Factory geometry bushing size for use with OEM and aftermarket poly bushings
Removeable air duct for easy access to sensors and drain/fill plug
Retains OEM speed sensor and wire mount location
Product development:
Our Reinforced Billet Diff Cover was designed, engineered, tested, and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer, and rigorous long-term product testing.
The ZF S5D 320Z 5-speed transmission is known for its robust design, exceptional durability, and impressive power-handling capability. Unfortunately, as these transmissions age, shifter-related issues have become increasingly common. Problems such as difficulty selecting gears, a sticky shifter, or a decline in shift quality are often the result of worn detent springs, pins, and bushings. These components are essential for precise gear engagement and proper shifter centering, making their replacement a critical step in maintaining optimal performance.
Replacing detents requires specialized tools known as "drifts," which are notoriously hard to find. Fortunately, we've developed a complete Detent Tool Kit, featuring five precision-engineered drifts designed for exact fitment in the ZF transmission's detent bores. This toolset makes detent replacement straightforward and minimizes the risk of damage to internal transmission components.
Features
Complete Tool Kit: Includes five precision-machined drifts specifically designed for the ZF 5-speed transmission’s detent bores and caps. Hassle-Free Detent Replacement: Simplifies the process of removing and installing detents with professional-grade precision. Protects Your Investment: Reduces the risk of damaging internal transmission components during service. Durable Construction: Made from heavy-duty 1045 steel for exceptional strength and long-lasting reliability.
BMW E36 328i, Z3 2.8 JB Racing Lightweight Aluminum Flywheel offers a significant performance upgrade by replacing the heavy stock steel flywheel with a much lighter aluminum version. This JB Racing flywheel is designed to deliver faster acceleration, improved throttle response, and enhanced overall performance for your BMW.
The modern stock flywheels are burdened with additional components meant to dampen vibrations, which unfortunately adds unnecessary weight. The JB Racing aluminum flywheel, weighing just 10.0 lbs compared to the stock 25.0 lbs, eliminates this excess mass, allowing more power to reach the wheels and reducing the energy wasted on spinning the flywheel. Engine builders prioritize lightweight flywheels when optimizing race engines for maximum efficiency, and the difference is especially noticeable in how quickly the engine revs and reaches its power band.
This JB Racing lightweight flywheel is a direct replacement for the stock flywheel and is compatible with the factory BMW organic clutch. This compatibility ensures that you can use standard replacement clutches, making maintenance simple and cost-effective. The flywheel can also be resurfaced for a fresh contact surface, so there’s no need to buy a new one when it’s time to replace the clutch.
While single-mass aluminum flywheels like this one may result in slightly more noise and vibration compared to dual-mass designs, this can be managed with heavier transmission oil and sprung hub clutches, such as the Sachs Performance clutch available through Turner Motorsport.
Vehicle Compatibility: