Packaged by Turner for BMW 3 Series E36 (1992-1998)

Often an oversight in maintenance, ignition components are also susceptible to wear and tear. Spark Plugs can accumulate carbon, reducing the spark intensity and it's ability to properly ignite the air/fuel mixture, leading to misfires and generally declining performance. Other ignition components, such as coils, boots, wires, caps, and rotors, can also wear out over time due to factors like heat and contamination, preventing the current from reaching the spark plug.

To start over fresh with all new components, we now offer these Ignition Service Kits. Each kit comes with brand new OE quality components, replacing any potential fault points in your ignition system for peak performance!

See kit contents below for a complete list of included components.

This kit is contains all new strut and shock mounts and hardware needed when installing a new shocks and struts or aftermarket suspension on your vehicle. 

Fits the following BMW's

E36 318i/ic/is 323i/ic/is 325i/is/ic 328i/is/ic 

When replacing your worn out brakes, the market is flooded with performance options. If your BMW doesn't see track time, it's not very practical. Performance pads and rotors tend to result in a lack of bite at low braking temperatures and cause excessive noise in daily driven vehicles that becomes irritating. BMW brakes from the factory are perfectly suited for trips around town, across the country, and even the occasional spirited driving session, delivering smooth, quiet, and long lasting performance. 

Included in this E36 BMW brake package are all of the OEM equivalent components needed to replace your Front & Rear brakes with comfort, reliability, and optimal lifespan in mind.

Brake components in this kit:

• Textar Front & Rear Brake Pads
• Zimmerman Front & Rear Rotors
• New Front & Rear Wear Sensors
• Brand New Stainless Steel Set Screws
• Syl-Glide Silicone Brake Lubricant 

Fits the following BMWs:
E36 BMW 318i/is/ic 323is 325i/is/ic 328i/is

When installing a new clutch, it is important to replace old hardware and common wear items. This ensures both a smooth and reliable installation. This also allows you to perform maintenance while everything is apart as opposed to a needing to make future repairs when everything is back together.

Included in this kit:

• Genuine BMW hardware with the exception of flywheel bolts which are an original equipment supplier
• 2 Genuine BMW E46 M3 transmission mounts
• Genuine BMW clutch fork pivot pin
• Original Equipment Supplier driveshaft washer gasket
• MTC universal flex disc (AKA Guibo) with hardware
• MTC driveshaft center carrier
• FAG pilot bearing
• Victor Reinz rear main seal

Fits the following BMWs:
E36 BMW M3 S50/52

Just like the rest of your vehicle's major systems, the cooling system must also be addressed periodically to ensure proper cooling and component reliability. Plastic and rubber components become brittle and prone to splitting or cracking after long periods of heating and cooling cycles, especially in colder climates! The coolant itself can degrade or become contaminated, leading to potential corrosion or freezing issues. Finally, thermostats and sensors can fail completely, preventing proper cooling and/or coolant temperature readings to become inaccurate.

To make sure you are not left stranded on the side of the road with an overheated engine, we have put together this Basic Cooling System Service kit. This kit contains all of the most-likely-to-fail components, giving you peace of mind knowing your engine will continue to run cool for another 60,000+ miles.

See kit contents below for all included components.

This strut and shock mount package covers the front and rear rubber mounts and bushings commonly replaced during a strut and shock install. While you're installing new front struts and rear shocks these are easily installed - there's no additional labor and special tools are not required. Since these pieces are mostly rubber, they dry up and crack over time. Re-using them lead to problems with fitment or noise, and may have safety issues as well. These mounts and pads are the perfect complement to your new shocks to help restore your car's handling and performance.

We sell the basic strut and shock mount package, which includes:

• Front strut mounts (also known as guide support)
• Front strut reinforcement plates (to prevent cracking and deforming of the front strut towers)
• Front strut tower paper washer gaskets
• Front and rear self-locking mounting nuts
• Rear Lifetime Warranty 'Repair Shop' shock mounts
• Rear shock mount reinforcements (to prevent cracking of shock towers)
• Rear shock mount gaskets

In addition, you can add the front spring pads, front bump stops, front dust boots, rear bump stops, and rear dust boots if needed. But please note that some shocks and coil overs come with all or some of these pieces already. If in doubt, check with your supplier on what is included.

We offer three varieties of the rear shock mounts - OEM, Repair Shop, and HP alum-rubber. We recommend either the Repair Shop or HP mounts because the stock OEM design has a flaw that can lead to premature failure of the mounts. The Repair Shop and HP mounts use a different design that will last longer and the Repair Shop mounts also have a lifetime warranty!

This item fits the following BMWs:
1996-1999 E36 BMW M3
1996-2002 Z3 BMW 2.5 2.5i 2.8 3.0i M Coupe

This kit is contains all new strut and shock mounts and hardware needed when installing a aftermarket suspension on your vehicle. 

Fits the following BMW's

1995 BMW E36 M3 S50 

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 3 kit replaces:

Control Arms & Bushings
Outer Tie Rods
Sway Bar End Links
Strut Tower Reinforcement Plate
Strut Mount & Gasket

When it comes time to replace your thermostat, be sure you have everything you need. This kit includes everything you need to replace your thermostat, including the thermostat.

Kit includes:

• Thermostat with gasket
• Thermostat mounting hardware
• 1 liter of coolant

This waterpump fits the following BMWs: 
1992-1999 E36 3 series - 323is, 323ic, 325i, 325is, 325ic, 328i, 328ic, M3 3.0 (S50/US), M3 3.2 (S52) 

The fan that attaches to the water pump carries so much rotational mass that it can actually hinder the performance of your engine. To address this, we now offer out line of fan delete kits that replace everything needed to get rid of your fan and fan clutch, without causing cooling issues as a result. This basic kit is the cheapest option, including just the bare essentials to get the job done and get your car running without a fan.

This kit is best for someone who has already upgraded their thermostat housing and/or water pump pulley and has performed regular maintenance on their engine drive belts.

Included in this kit:

• 80* thermostat
• 1 liter of coolant
• Water Wetter coolant additive
• Low-temperature coolant temperature sensor/switch

Fits the following BMWs:
1992-09/1995 E36 BMW 325i/is/ic 328i/is/ic M3

**This kit is intended to be used with cars that have a functional auxiliary fan (64508364093) or an upgraded electrical fan installed.**

The fan that attaches to the water pump carries so much rotational mass that it can actually hinder the performance of your engine. To address this, we now offer out line of fan delete kits that replace everything needed to get rid of your fan and fan clutch, without causing cooling issues as a result. This Ultimate kit is the top tier option, including the essential conversion components, the upgraded aluminum thermostat housing, and a brand new accessory belt.

This kit is best for someone who has not performed recent cooling system maintenance or who wants to replace everything at once for increased reliability and longevity.

Included in this kit:

• 80* thermostat
• 1 liter of coolant
• Water Wetter coolant additive
• Low-temperature coolant temperature sensor/switch
• Aluminum thermostat housing with gaskets
• Fan delete nut
• ECS  Aluminum Water Pump Pulley - Black
• Accessory Belt

Fits the following BMWs:
1992-09/1995 E36 BMW 325i/is/ic 328i/is/ic M3

**This kit is intended to be used with cars that have a functional auxiliary fan (64508364093) or an upgraded electrical fan installed.**

Automatic transmissions are reliable, shift smoothly, and can last without issue so long as they are properly maintained. Over time, the transmission fluid becomes thick and the filter becomes contaminated with small metal particles. This can cause excess wear, high transmission operating temperatures, and eventual failure. To prevent this we recommend changing your filter, fluid, and seals to ensure your transmission continues to operate flawlessly. We recommend filter and fluid changes every 50,000 miles. This kit includes Redline D4 ATF, the transmission filter, gasket and bolts. This filter fits A4S 270R/310R automatic transmissions on BMW E36 318i 318is 318ic 318it 323is 323ic 325i 325is 325ic 328i 328is 328ic. E34 525i M50. E39 528i Z3 2.3 2.8. 

Kit Includes:

• Automatic transmission filter with associated hardware
• Oil pan gaskets with hardware
• Fill plug with sealing washer
• 7 quarts Redline D4 automatic transmission fluid

This item fits the following BMWs: 
1992-1999  E36 BMW  318i 318is 318ic 318ti 323is 323ic 325i 325is 325ic 328i 328is 328ic 
1991-1995  E34 BMW  525i 
1997-09/1999  E39 BMW  528i 
1997-2000  Z3 BMW  Z3 2.3 Z3 2.8

The fan that attaches to the water pump carries so much rotational mass that it can actually hinder the performance of your engine. To address this, we now offer out line of fan delete kits that replace everything needed to get rid of your fan and fan clutch, without causing cooling issues as a result. This Comprehensive kit is the mid-priced option, including the essentials and an upgraded aluminum thermostat housing that won't crack or break like the brittle plastic housing. 

This kit is best for someone who wants to upgrade their thermostat housing to aluminum, has already upgraded their water pump pulley, and has performed regular maintenance on their engine drive belts.

Included in this kit:

• 80* thermostat
• 1 liter of coolant
• Water Wetter coolant additive
• Low-temperature coolant temperature sensor/switch
• Aluminum thermostat housing with gaskets
• Fan delete nut

Fits the following BMWs:
09/1995-1999 E36 BMW 323is/ic 328i/is/ic M3

**This kit is intended to be used with cars that have a functional auxiliary fan (64508364093) or an upgraded electrical fan installed.**

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 3 kit replaces:

Control Arms & Bushings
Outer Tie Rods
Sway Bar End Links
Strut Tower Reinforcement Plate
Strut Mount & Gasket