Emissions System for BMW E46 M3 S54 (1999-2005)

The factory rubber/plastic hoses become brittle and crack over time. Brittle and cracked hoses can cause multiple vacuum leaks that are impossible to repair without hose replacement. Vacuum leaks can cause many problems including rough running, missing, stalling at idle, and even a no-start condition.

The factory hoses offered through BMW are plastic and will yield the same results of becoming brittle and damaged over time. Our solution is a premium replacement that will outlast everyone of the OEM replacements. Our Silicone Crankcase Vent Hose can be used to replace the factory brittle hose to ensure your S54 is free from vacuum leaks and performing properly.

CSL Vent Hose (11157833649) - Silicone Crankcase Vent hose is a direct replacement

Key benefits:

Lifetime replacement of the brittle OEM plastic crankcase breather hose that is susceptible to cracking overtime from constant heat cycling

Design:

Retains OEM hose end fittings to ensure proper seal

“Black” 3 ply reinforced silicone w/ “White” Turner logo

Our engineers at Turner sought out to solve the degrading issues that happens with the factory crankcase vent hose and found the best solution is a silicone replacement. Our Turner Silicone Crankcase Vent Hose can be used to replace the factory brittle hose to prevent vacuum leaks and lackluster performance. Simply take your factory crankcase vent hose and remove the ends; the factory ends can be installed on the new Silicone Vent Hose with the supplied clamps for a tight seal.

Turner Silicone Crankcase Vent Hose replaces the following part #'s:

CSL Vent Hose (11157833649) - Silicone Crankcase Vent hose is a direct replacement
Non-CSL Vent Hose(11157831311) - Silicone hose will make a "U" bend with direct fitment and can also be trimmed for your own preferable fit.

- Key benefits:

Lifetime replacement of the brittle OEM plastic crankcase breather hose that is susceptible to cracking overtime from constant heat cycling
- Design:

Turner logo forward facing when hood is open
Retains OEM hose end fittings to ensure proper seal and reduce cost
“Black” 3 ply reinforced silicone w/ “White” Turner logo
includes 2 German style 430 stainless worm-drive clamps for installation
- Special care instructions:

Do not overtighten hose clamps, hand tight is recommended.
Carefully cut the OEM plastic casing from both plastic fittings for reuse

When we designed this catch we wanted to have the most function options available, the best separation method, and the easiest to service. The Turner engineered catch cans offer a pre-setup design based ion desired flow direction, however this does not limit you to this flow. The inner baffle orientation can be easily adjusted to flow in both directions in case you decide to move this catch can to a different vehicle. A 4 chamber system  baffle system inside the catch can was engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can. Having a closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation.

Our catch can was also designed with the idea that the cans fill level can easily be checked with a top mounted dipstick and an optional use bottom drain hole. The drain hole can be used with a valve and hose to be mounted at a lower area of the vehicle so when you're doing an oil change you can drain the catch can.

Features:

• 6061-T6 billet machined body, anodized black for lasting protection and appearance
• Strategically positioned 4 chamber baffle system maximizes oil / air separation 
• Knurled and black anodized oil dipstick makes inspecting oil volume of reservoir clean and simple
• Sealed with a pre-installed viton O-Ring
• Includes 2.5mm allen key to remove baffle plates for cleaning
• Engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can
• Closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation
• Optional use drain hole (valve and hose sold separately, watch for our model specific drain kits!)

A combination of billet fittings and AN lines for an upgraded and serviceable crankcase vent hose. Attaches between the oil separator and the CSL air box.

The factory rubber/plastic hoses become brittle and crack over time. Brittle and cracked hoses can cause multiple vacuum leaks that are impossible to repair without hose replacement. Vacuum leaks can cause many problems including rough running, missing, stalling at idle, and even a no-start condition. The factory hoses offered by BMW are plastic and will yield the same results of becoming brittle and damaged over time.

We have created a full motorsport-style solution with our CSL Crankcase made from machined 6061 billet aluminum with AN-style fittings and nylon fiber braided lines. This is a fully serviceable replacement that will outlast every one of the OEM replacements. Our AN crankcase line can be used to replace the factory brittle hose to ensure your S54 is free from vacuum leaks and performing properly.

OEM CSL Vent Hose (11157833649) - Direct Replacement for cars with secondary shut-off valve. (11157834056)

Key benefits:

Lifetime replacement of the brittle OEM plastic crankcase breather hose
Fully Serviceable
Motorsport Aesthetic to compliment your CSL Intake Plenum
Design:

Fittings are made from billet 6061-T6 aluminum and finished in Type II black anodizing
Pre-anodized machined Turner branding
Nylon fiber braided lines
Fittings are a direct replacement for the plastic OEM fittings
Not for sale or use in the state of California on any pollution-controlled vehicle as per the California Air Resources Board.

Upgrade your exhaust system with the Stainless Steel Oxygen Sensor (O2) Weld Bung (M18x1.5mm). This high-quality weld bung is made from stainless steel, ensuring durability and resistance to corrosion. It features M18x1.5mm threads, making it compatible with most oxygen sensors. Perfect for custom exhaust setups or replacing damaged bungs, this weld bung is a must-have for any automotive enthusiast.

• Made from high-quality stainless steel for durability and corrosion resistance
• M18x1.5mm threads ensure compatibility with most oxygen sensors
• Ideal for custom exhaust setups or replacing damaged bungs
• Essential for automotive enthusiasts looking to upgrade their exhaust system

Crankcase Vent Hose ABV0329 is an essential component designed for BMW engines, ensuring optimal performance of the crankcase ventilation system. This high-quality vent hose plays a critical role in regulating and redirecting excess gases from the crankcase back into the engine's intake, reducing harmful emissions and preventing pressure buildup. Crankcase Vent Hose ABV0329 helps maintain engine efficiency and protects against potential damage caused by over-pressurization or oil leaks.

Made from durable, heat-resistant materials, this hose is built to withstand the high temperatures and pressures common in BMW engines. It is a direct-fit replacement, making installation simple and efficient for both professionals and DIY mechanics. Available from Turner Motorsport, Crankcase Vent Hose ABV0329 is the perfect solution for restoring and maintaining your BMW’s crankcase ventilation system.

Key Benefits:

• Ensures proper crankcase ventilation for optimal engine performance
• Reduces harmful emissions by redirecting excess gases into the intake
• Prevents pressure buildup and protects against oil leaks
• Constructed from durable, heat-resistant materials for long-lasting reliability
• Direct-fit replacement, ensuring easy installation for various BMW models
• Available from Turner Motorsport, a trusted source for BMW performance parts

1.5mm X 51mm Metric Buna-N 70 O-ring is the perfect sealing solution for various industrial applications. Made from high-quality Buna-N material, this O-ring provides reliable sealing performance, ensuring leak-free connections. With its metric sizing and 70 durometer hardness, it offers versatility and durability for a wide range of uses.

• High-quality Buna-N material
• Reliable sealing performance
• Metric sizing for versatility
• 70 durometer hardness for durability

Easily add an oxygen sensor to your custom exhaust setup with this universal O2 sensor bung. Designed for simple weld-on installation, it allows you to place your sensor exactly where you need it—perfect for custom builds, exhaust modifications, or performance tuning projects.

Features:

CNC-cut from T304 Stainless Steel for corrosion resistance
Threaded for M18x1.5mm RH oxygen sensors