BMW Suspension Parts for BMW 3 Series E46 (1999-2005)

Clear BMW chassis

Please ensure your correct model is selected

Your BMW's handling is determined by the capabilities and age of your suspension components. Our selected aftermarket performance suspension like coilovers, lowering springs, cup kits, and dampers can improve the handling of your BMW dramatically. With those upgrades comes the needs for proper adjustment; our recommended supporting modifications comes stiffer sway bars, bushings, and adjustable camber/caster plates, to name a few found on this page. Completely build your suspension for the most competitive BMW driving experience, achieve your perfect look, or simply replace your worn suspension with our recommended parts.

Sub-Categories

Sort By:

KMAC - Corporate Logo
T#:389645
Part#: 192416-1J
In Stock
$ 380.00 USD
Free Shipping
$ 380.00 USD
Free Shipping
Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012  E82 BMW  128i 135i
6/1992-1999  E36 BMW  318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005  E46 BMW  323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011  E90 BMW  325i 328i 330i 335d 335i - Sedan
2006-2012  E91 BMW  328i - Wagon
2007-2013  E92 BMW  328i 335i 335is - Coupe
2007-2013  E93 BMW  328i 335i - Convertible
1997-2003  E39 BMW  525i 528i 530i 540i (not for cars with EDC)
2004-2010  E60 BMW  525i 530i 528i 535i 545i 550i
2004-2011  E63 E64 BMW  645ci 650i
1997-2002  Z3 BMW  Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008  E85 BMW  Z4 2.5i Z4 3.0i Z4 3.0si
2009+  Z4 BMW  Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003  E52 BMW  Z8 Roadster (without EDC)
Show More Show Less
Whiteline - Corporate Logo
T#:558797
Part#: W61923
In Stock
$ 77.99 USD
Free Shipping on orders $49 and up

Optimize rear suspension geometry with Whiteline suspension bushings. Often overlooked, Whiteline trailing arm bushings offer superior dynamic alignment precision by controlling excessive movement - providing driver reassurance for more predictable handling.

Features:

  • Performance - Whiteline's engineered "Synthetic Elastomer" bushings feature the quality ride of rubber at lower speeds and at higher speeds react when under cornering, accelerating and braking loads, for CHASSIS CONTROL and improved handling.
  • Durable - The advanced synthetic elastomer characteristics ensure superior elasticity, memory and outright durability for all forms of driving applications!
  • Resistant - Whiteline's synthetic elastomer formulation boasts resistance to oil, grease, ozone and weathering
  • Lubricant - Supplied with extreme pressure molybdenum disulphide (LM) based grease (where required) for extended life.
  • Installer Friendly - Designed with the installer in mind by reducing the need of specialized skills, tools and equipment.
  • Black - The neutral (black) appearance favored by restorers and racers.
  • Lifetime Warranty - All Whiteline bushing kits are backed by a lifetime warranty
Show More Show Less
Whiteline - Corporate Logo
T#:558799
Part#: KLC163
Ships in 3 Business Days
$ 167.99 USD
Free Shipping on orders $49 and up

Links are a common service item due to either worn or over compliant joints and possibly bent or snapped center bodies. Upgrade from the old units to Whiteline sway bar links with superior features that outlast and outperform the original equipment.

The threaded center rod allows for precise adjustment and can be cut to a needed length for precise suspension tuning.

Show More Show Less

Whiteline - Corporate Logo
T#:372180
Part#: KSB557
In Stock at Vendor
$ 228.99 USD
Free Shipping
$ 228.99 USD
Free Shipping

BMWs need some added chassis strengthening in the front for best potential handling. Whiteline has the solution with a stylish polished aluminum strut brace that offers easy installation and increases chassis rigidity.

This part fits the following BMWs:
1999-2006 E46 ALL

Show More Show Less

Whiteline - Corporate Logo
T#:26538301
Part#: W53518
In Stock
$ 133.99 USD
Free Shipping on orders $49 and up
Following meticulous development and material testing focused on strength, durability, geometry retention, and memory while maintaining comfort, WHITELINE has engineered a progressive, long-chain Synthetic Elastomer. This pioneering material merges the advantageous properties of solid bushings with the flexibility of rubber.
Show More Show Less
Whiteline - Corporate Logo
T#:372857
Part#: W62384
Ships in 3 Business Days
$ 118.99 USD
Free Shipping on orders $49 and up

These bushings replace the stock rubber bushings and offer a better driving feel, increased lifespan, and better wheel alignment.

Rubber bushing allow for a lot more movement and are more susceptible to wear and tear from spirited driving and harsh weather conditions. Polyurethane is much more resistant to wear and is stiffer, reducing the total amount of movement that would normally affect the alignment negatively.

Show More Show Less

Whiteline - Corporate Logo
T#:26638232
Part#: W23394
Ships in 3 Business Days
$ 25.99 USD
Free Shipping on orders $49 and up
After extensive development and material testing focused on delivering strength, durability, geometry retention, and memory while maintaining comfort, WHITELINE has introduced a progressive, long-chain Synthetic Elastomer. This groundbreaking material merges the advantageous properties of solid bushings with the flexibility of rubber, resulting in improved performance attributes.
Show More Show Less
Whiteline - Corporate Logo
T#:372178
Part#: BBF15Z
In Stock at Vendor
$ 377.99 USD
$ 377.99 USD

Sway bars are an essential upgrade when trying to get the best handling capabilities out of your BMW. Stock sway bars allow for too much play and excessive body roll, not keeping the wheels as firmly planted as they should be. Whiteline offers their performance sway bar kits that are designed to improve your BMW's handling characteristics and come with upgraded polyurethane bushings as well.

This Whiteline 30mm sway bar gives you more grip, better handling, and better outright performance. Sway bar upgrades are one of the best dollar-for-dollar investments you can make, improving your BMW's handling dynamics without affecting the comfort or ride quality.


This part fits the following BMWs:
2001 - 2006 E46 M3

Show More Show Less

Whiteline - Corporate Logo
T#:26638241
Part#: W53519
Ships in 3 Business Days
$ 116.99 USD
Free Shipping on orders $49 and up

Whiteline - Corporate Logo
T#:26638282
Part#: W72045
Ships in 3 Business Days
$ 45.99

This product was last offered at the strikethrough price on
08-13-2026

$ 41.99 USD
Free Shipping on orders $49 and up
$ 41.99 USD
Free Shipping on orders $49 and up
This rubber mount is located between the rear spring and the body.
Whiteline - Corporate Logo
T#:372177
Part#: BBR11Z
In Stock at Vendor
$ 305.99 USD
$ 305.99 USD

Sway bars are an essential upgrade when trying to get the best handling capabilities out of your BMW. Stock sway bars allow for too much play and excessive body roll, not keeping the wheels as firmly planted as they should be. Whiteline offers their performance sway bar kits that are designed to improve your BMW's handling characteristics and come with upgraded polyurethane bushings as well.

This Whiteline 20mm sway bar gives you more grip, better handling, and better outright performance. Sway bar upgrades are one of the best dollar-for-dollar investments you can make, improving your BMW's handling dynamics without affecting the comfort or ride quality.

This part fits the following BMWs:
1999-2006 E46 RWD Non-M

Show More Show Less
Whiteline - Corporate Logo
T#:54388458
Part#: W22801
Ships in 3 Business Days
New Item
$ 28.99

This product was last offered at the strikethrough price on
08-13-2026

$ 26.99 USD
Free Shipping on orders $49 and up
$ 26.99 USD
Free Shipping on orders $49 and up
Engineered to optimize rear roll stiffness and eliminate the dynamic compliance of aging factory components


KMAC - Corporate Logo
T#:389647
Part#: 192416-2L
Ships on Sep 9, 2026
$ 545.00 USD
Free Shipping
$ 545.00 USD
Free Shipping
Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 2 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012  E82 BMW  128i 135i
6/1992-1999  E36 BMW  318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005  E46 BMW  323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011  E90 BMW  325i 328i 330i 335d 335i - Sedan
2006-2012  E91 BMW  328i - Wagon
2007-2013  E92 BMW  328i 335i 335is - Coupe
2007-2013  E93 BMW  328i 335i - Convertible
1997-2003  E39 BMW  525i 528i 530i 540i (not for cars with EDC)
2004-2010  E60 BMW  525i 530i 528i 535i 545i 550i
2004-2011  E63 E64 BMW  645ci 650i
1997-2002  Z3 BMW  Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008  E85 BMW  Z4 2.5i Z4 3.0i Z4 3.0si
2009+  Z4 BMW  Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003  E52 BMW  Z8 Roadster (without EDC)
Show More Show Less
KMAC - Corporate Logo
T#:389646
Part#: 192416-3L
Special Order: No Guaranteed ETA
$ 545.00 USD
Free Shipping
$ 545.00 USD
Free Shipping
Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 3 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012  E82 BMW  128i 135i
6/1992-1999  E36 BMW  318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005  E46 BMW  323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011  E90 BMW  325i 328i 330i 335d 335i - Sedan
2006-2012  E91 BMW  328i - Wagon
2007-2013  E92 BMW  328i 335i 335is - Coupe
2007-2013  E93 BMW  328i 335i - Convertible
1997-2003  E39 BMW  525i 528i 530i 540i (not for cars with EDC)
2004-2010  E60 BMW  525i 530i 528i 535i 545i 550i
2004-2011  E63 E64 BMW  645ci 650i
1997-2002  Z3 BMW  Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008  E85 BMW  Z4 2.5i Z4 3.0i Z4 3.0si
2009+  Z4 BMW  Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003  E52 BMW  Z8 Roadster (without EDC)
Show More Show Less
KMAC - Corporate Logo
T#:389317
Part#: 193616-2L
Special Order: No Guaranteed ETA
$ 545.00 USD
Free Shipping
$ 545.00 USD
Free Shipping
Location: Front
Type: Street/Track, Stage 2
Bearing: PTFE-lined pillow-ball with thin polyurethane bushing

The Stage 2 KMAC plates are a mixed street/track camber/caster plate meant to be used in a variety of suspensions. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions. Bearing inserts and adapters included. The Stage 2 camber plates are shorter than a factory mount so may not be suitable for cars will little suspension travel. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2006-2008  E85 BMW  Z4 M Roadster M Coupe
Show More Show Less

KMAC - Corporate Logo
T#:389662
Part#: 193616-3L
Special Order: No Guaranteed ETA
$ 545.00 USD
Free Shipping
$ 545.00 USD
Free Shipping
Location: Front
Type: Track, Stage 3
Bearing: PTFE-lined pillow-ball, no bushing

KMAC Stage 3 camber/caster plates are designed for track or race-only situations where comfort and noise are not the primary concerns. The Stage 3 camber plates use a pillowball bearing, solidly mounted within the camber plate for direct alignment of the strut shaft and no excess play or deflection. Stage 3 are designed to increase negative camber with their patented 'floating' adjustment that changes camber and caster together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Fitment is limited to race-only small diameter coil-over springs (not stock-type). Bearing inserts and adapters included. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1997-2003  E39 BMW  525i 528i 530i 540i (for cars with EDC)
1999-2003  E39 BMW  M5
1995-2001  E38 BMW  740i 740il 750il (for cars with EDC)
2004-2010  E60 BMW  M5
2004-2011  E63 BMW  M6
Show More Show Less

Whiteline - Corporate Logo
T#:54388459
Part#: W52605
Ships in 3 Business Days
New Item
$ 66.99

This product was last offered at the strikethrough price on
08-13-2026

$ 61.99 USD
Free Shipping on orders $49 and up
$ 61.99 USD
Free Shipping on orders $49 and up
Deflection at the front lower control arm rear pivot drastically alters dynamic toe and caster alignment under high-load braking and cornering