BMW Performance Clutch Kits & Parts for BMW 3 Series E46 (1999-2005)

This braided stainless steel line replaces the stock hydraulic hose connecting your clutch slave cylinder to the clutch master cylinder. There are several deficiences with rubber, especially as it ages - when new the rubber expands and swells under pressure and the pedal can feel spongy. As rubber ages and is exposed to extreme temperatures the rubber can harden and even shrink (common on brake hoses), which results in a stiff pedal. Rubber clutch lines do not stand up to the stresses of hard use. ECS Exact-Fit stainless reinforced clutch lines provide more confident and dependable shifting by maintaining consistent line pressure, long lasting corrosion resistance, and increased protection from failure. These lines are reinforced with braided stainless steel mesh, affording superior expansion resistance. This resistance to expansion creates a firmer pedal, and a more direct clutch pedal feel. The signature red polymer coating provides additional protection from the elements and abrasion.

This particular stainless steel clutch line fits the following BMWs:
1999-2005 E46 3 Series (all) including 323i, 323Ci, 325i, 325xi, 325Ci, 328i, 328Ci, 330i, 330xi, 330Ci
2001-2006 E46 M3 (manual transmission only, no SMG)
2004-2009 X3 SAV including X3 2.5, X3 3.0

Replace this tube whenever the bearing or clutch kit is replaced.

Genuine BMW Guide Tube
This item fits the following BMW Chassis:
E36 M3,E34,E36,E39,E46,E53 X5
 

Requires shorter flywheel bolts - 8x (P# 11227805885) - T#12322

Lightweight flywheels have proven themselves to be a worthwhile performance enhancement. But with the quicker throttle response and horsepower improvement comes one serious drawback: flywheel chatter. Without the dual-mass flywheel's rubber isolators, a lightweight aluminum flywheel has more rattle than stock. ECS has designed this flywheel using chrom-moly steel and it weighs almost ten pounds less than the stock DMF but not as extreme as full aluminum flywheels. The steel helps dampen vibration and noise so you get near-factory refinement and most of the benefits of a lightweight flywheel: quicker throttle response, better reliability, and more power to the wheels. This flywheel requires the E34 M5 sprung hub clutch kit.

Modern flywheels are built with additional components that are designed to dampen and minimize vibrations from the engine and transmission. Weight has increased and reliability has decreased. With additional weight more energy is required for it to move. A lightweight flywheel does away with the dual mass design and its additional mass so more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance. And with a single-mass flywheel the unreliable DMF design is eliminated.

Stock flywheel weight - 25.0lbs
ECS flywheel weight = 16.55lbs

This item fits the following BMWs:
1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2002 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (5-speed)
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2005 E85 BMW Z4 2.5i Z4 3.0i (5-speed)

Some modifications to your vehicle may not produce power to create gains in the overall performance of your driving. When you add a "Po' Boy" clutch stop to your BMW the performance gain is directly felt in the driving experience.

The ECS clutch stop allows the driver to fine tune the position of the clutch pedal to closely match the engagement point for precise, quicker shifting. The adjustment range found in this product can be set to the stock engagement point or can be adjusted to follow the wear of the clutch.  Meaning your new experience will never change all the way to the end of the clutch life and can be reset to enjoy the next clutch.

Note: This modification might require some slight modification to the clutch switch mounting bracket, which can be bent slightly by hand.

Looking to eliminate your dual-mass flywheel? Overwhelmed with all the options, but hearing complaints about so many of them with rattling or chatter from them? Problem solved. Introducing the all-new Lightweight Performance Flywheel from ECS Tuning. Engineered in-house with the enthusiast daily driver in mind, this is the perfect option for those wanting a lightweight flywheel without the annoying chatter heard from so many other options on the market. Designed to accommodate all conditions: from Sunday drives through the country, to the abuse of the track. No matter your driving style or ability, this is the flywheel and clutch kit for you.

Key Features:

Eliminates factory dual-mass flywheel for:
Crisper shifts
Improved throttle response
Improved acceleration (We measured a .4s decrease in 0-60 times on an otherwise-stock E36 328i!)
Lower replacement cost
Hardened 4140 Chromoly Steel for excellent engagement feel and wear resistance; zinc plated for corrosion resistance
Designed for use with any E34 M5 pressure plate and clutch for OE-type clutch feel
Sprung-hub clutch disc to eliminate chatter at idle and reduce driveline shock loading
Weighs in at just 16.5lbs!
SFI tested and certified to ensure safe operation under all conditions
Includes ECS performance flywheel, clutch kit with throwout bearing, pilot bearing and all flywheel and pressure plate hardware
Why is SFI testing and certification important?

The SFI Foundation, Inc. (SFI) is a non-profit organization established to issue and administer standards for the quality assurance of specialty performance and racing equipment. SFI certification indicates a flywheel has been certified using industry-standard SFI Spec 1.1 standards by an independent testing body to ensure quality of both design and materials for flywheels utilized in competitive motorsports.

Having successfully passed SFI certification, this flywheel has an individual SFI serial number found in a laser etching, and on an affixed sticker. This certification means the ECS-engineered flywheel is safe and reliable during the rigors of competitive racing; it's also safe and reliable for years and years of street use.

If your clutch switch is bad, it will prevent the car from starting and seem similar to a bad starter, you will turn the key and nothing will happen. Replace yours to start your vehicle again.

Genuine BMW Module, Clutch Switch
This item fits the following BMW Chassis:
E39 M5,E46 M3,E85 Z4M,E39,E46,E85 Z4,E86 Z4
 

Lightweight flywheel and upgraded clutch kit for improved throttle response, acceleration, and clutch feel - the perfect setup for daily-driven vehicles with up to 400 Ft/lbs of torque.

This performance clutch and flywheel kit utilizes an upgraded ECS E34 M5 clutch kit with their in-house engineered flywheel to fit all M5x and S5x motors with a 5-speed transmission. By eliminating the dual-mass flywheel and replacing it with a single-mass you are able to eliminate the slack and extra weight of the flywheel for a quicker throttle response and acceleration. Their upgraded clutch kit utilizes all the best features of the original M5 clutch with an upgraded pressure plate and clutch disc, with the new clutch you have a better, more engaged clutch pedal feel, engagement, and longevity.

Whether you're replacing a worn-out clutch or upgrading for increased power handling, this E34 M5 clutch and flywheel kit offers a reliable solution for enhanced pedal feel, power capacity, and overall driving satisfaction.

Paired with a modified geometry flywheel, the E34 M5 style clutch is ideally suited for most E36, E46, and others using the same powertrain. It checks all the boxes for essential clutch replacement features. While some aftermarket options may address slipping issues and worn-out clutches, they often sacrifice pedal feel, providing little to no resistance. A soft clutch not only kills the driving experience of your BMW but also reduces confidence when pushing the car to its limits.

On the contrary, you might be in the market for an upgraded clutch to handle your modified engine/forced induction builds. You go from an OE or aftermarket clutch option that has a lackluster and soft pedal feel to the complete opposite side of the spectrum, a very stiff clutch that grabs like an on-and-off switch making the clutch a pain almost undrivable on the street resulting in your favorite car turning into your least favorite car to drive.

The E34 M5 clutch and flywheel kit balances performance with practicality, ensuring a satisfying driving experience whether you're maintaining your BMW or preparing it for increased power demands.

Kit Contents:

Single Mass Flywheel - E34 M5 Clutch Geometry
Performance Clutch Disc and Pressure plate
Throw-out Bearing
Pilot Bearing
Clutch Alignment Tool
Flywheel Bolts - Qty 8
Pressure Plate Botls - Qty 6
Clutch features:

Torque Capacity (Crankshaft):
400 Ft / Lbs
Clutch Disc:
240mm Full face, performance organic friction material with integrated copper for enhanced heat dissipation and a long component life
OE-like friction backing plate design for smooth engagement with dual-stage damping springs to reduce gear noise and driveline chatter, and for smooth engagement
Pressure Plate
Increased clamp force over OEM, rated at 1,729lbs of pressure
Flywheel features:

Eliminates factory dual mass
Improved throttle response
Improved acceleration
Hardened 4140 Chromoly Steel
Designed for use with any E34 M5 pressure plate and clutch for OE-type clutch feel
Weighs in at just 16.5lbs vs Factory Dual Mass - 25.3 lbs
SFI certified
Fitment:
1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2002 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (5-speed)
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2005 E85 BMW Z4 2.5i Z4 3.0i (5-speed)

Lightweight flywheels have proven themselves to be a worthwhile performance enhancement. But with the quicker throttle response and horsepower improvement comes one serious drawback: flywheel chatter. Without the dual-mass flywheel's rubber isolators, a lightweight aluminum flywheel has more rattle than stock. ECS has designed this flywheel using chrom-moly steel and it weighs almost ten pounds less than the stock DMF but not as extreme as full aluminum flywheels. The steel helps dampen vibration and noise so you get near-factory refinement and most of the benefits of a lightweight flywheel: quicker throttle response, better reliability, and more power to the wheels. Zero-balanced and SFI 1.1 certified (material and design has been independently burst tested to ensure quality and safety). This flywheel requires the E34 M5 sprung hub clutch kit. Choose below from the flywheel only or a complete kit.

Modern flywheels are built with additional components that are designed to dampen and minimize vibrations from the engine and transmission. Weight has increased and reliability has decreased. With additional weight more energy is required for it to move. A lightweight flywheel does away with the dual mass design and its additional mass so more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance. And with a single-mass flywheel the unreliable DMF design is eliminated.

Stock flywheel weight - 25.0lbs
ECS flywheel weight = 16.55lbs

This item fits the following BMWs:
1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2002 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (5-speed)
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2005 E85 BMW Z4 2.5i Z4 3.0i (5-speed)