Please ensure your correct model is selected
BMW S54 VAC Performance Coated Rod Bearing Kit is highly regarded by BMW engine builders worldwide for its superior quality and performance. Ideal for both forced induction and naturally aspirated builds, these coated bearings are designed to be friction-resistant, reducing the risk of thermal breakdowns due to inadequate lubrication. This feature significantly decreases the chances of premature engine failure in street cars and minimizes the risk of spun bearings during high-stress track conditions.
The VAC Performance Coated Rod Bearing Kit is proven to help maintain engine reliability, even in situations with reduced oil pressure.
VAC Tech Notes:
Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent. The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories. These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.
Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.
This part fits the following BMW engines:
S54
This part fits the following chassis:
E46, Z3, Z4
VAC's S54 Vanos Hub is designed as a direct replacement for the fragile BMW OE Vanos Hub which typically fails due to a broken drive pin. The VAC Hub has an Upgraded Drive Pin design, which is larger in diameter, as well as more material on the outside wall of the pin. In addition, the hub is made from 4340HT Billet Bar and heat treated to the same BMW OE Rockwell Hardness spec. The upgraded design is not only significantly stronger, but the larger diameter Drive Pins also minimize the huge clearance (approximately 1mm) that was in the original design by BMW and reduces the clearance to 0.2mm. This is critical in helping greatly reduce or eliminate the VANOS noise.
Also, this upgraded design eliminates the need for modifying the Pump Ring or having to buy a replacement, which further saves you money!!!
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
BMW Supercharger Kits can be found all over the internet, but who should you choose to go with? If you want to go to with a forced induction system and want reliability and a driving feel that isn't adversely affected, the VF Engineering Supercharger Kit is one of the best options on the market. Included with every supercharger system is their custom proprietary VF.GIAC software that safely realigns all fueling and engine management parameters for optimal performance and long term drivability. Unlike many other options that are available, the VF Supercharger kit is designed to work with BMW's OEM parameters to minimize the likelihood of DTCs (Diagnostic Trouble Codes) and Check Engine Lights.
This 6.0 psi VF Engineering supercharger system is designed for simple bolt-on installation, remains fully OBD2 compliant, and can be installed in a single day, ready to run in approximately 8 hours. This kit is also non-intrusive and is fully reversible.
The 6.0 psi manifold at peak boost was tested to be the optimal induction charge limit without aftercooling and offers max tourqe gains!
Upon ordering, you will be required to send your VIN number, ECU, and transmission type (auto or manual) to VF Engineering within 1 year of purchase for your software flash of the ECU.
This product is supported by a 1 year unlimited mileage warranty on the product only.
This product was last offered at the strikethrough price on
09-10-2026
Elevate your BMW's engine performance with Schrick's premium camshafts, crafted with over 40 years of dedication to excellence. Catering to both street and track enthusiasts, Schrick ensures top-quality materials for strength and accuracy. This renowned brand has formed a lasting bond with BMW enthusiasts, providing advanced camshaft options that have stood the test of time.
Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent. The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories. These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.
Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.
Fits the following BMWs:
2000-2006 E46 BMW 323/325/328/330
Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent. The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories. These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.
Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.
This part fits the following BMW engines:
S54
This part fits the following chassis:
E46, Z3, Z4
BMW Supercharger Kits can be found all over the internet, but who should you choose to go with? If you want to go to with a forced induction system and want reliability and a driving feel that isn't adversely affected, the VF Engineering Supercharger Kit is one of the best options on the market. Included with every supercharger system is their custom proprietary VF.GIAC software that safely realigns all fueling and engine management parameters for optimal performance and long term drivability. Unlike many other options that are available, the VF Supercharger kit is designed to work with BMW's OEM parameters to minimize the likelihood of DTCs (Diagnostic Trouble Codes) and Check Engine Lights.
This 6.0 psi VF Engineering supercharger system is designed for simple bolt-on installation, remains fully OBD2 compliant, and can be installed in a single day, ready to run in approximately 8 hours. This kit is also non-intrusive and is fully reversible.
The 6.0 psi manifold at peak boost was tested to be the optimal induction charge limit without aftercooling and offers max tourqe gains!
Upon ordering, you will be required to send your VIN number, ECU, and transmission type (auto or manual) to VF Engineering within 1 year of purchase for your software flash of the ECU.
This product is supported by a 1 year unlimited mileage warranty on the product only.
BMW Supercharger Kits can be found all over the internet, but who should you choose to go with? If you want to go to with a forced induction system and want reliability and a driving feel that isn't adversely affected, the VF Engineering Supercharger Kit is one of the best options on the market. Included with every supercharger system is their custom proprietary VF.GIAC software that safely realigns all fueling and engine management parameters for optimal performance and long term drivability. Unlike many other options that are available, the VF Supercharger kit is designed to work with BMW's OEM parameters to minimize the likelihood of DTCs (Diagnostic Trouble Codes) and Check Engine Lights.
This 6.0 psi VF Engineering supercharger system is designed for simple bolt-on installation, remains fully OBD2 compliant, and can be installed in a single day, ready to run in approximately 8 hours. This kit is also non-intrusive and is fully reversible.
The 6.0 psi manifold at peak boost was tested to be the optimal induction charge limit without aftercooling and offers max tourqe gains!
Upon ordering, you will be required to send your VIN number, ECU, and transmission type (auto or manual) to VF Engineering within 1 year of purchase for your software flash of the ECU.
This product is supported by a 1 year unlimited mileage warranty on the product only.
