BMW Engine Parts for BMW 3 Series E46 (1999-2005)

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent.  The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories.  These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

This part fits the following BMW engines:
S54

This part fits the following chassis:
E46, Z3, Z4

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent.  The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories.  These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

This part fits the following BMW engines:
S54

This part fits the following chassis:
E46, Z3, Z4

BMW Supercharger Kits can be found all over the internet, but who should you choose to go with? If you want to go to with a forced induction system and want reliability and a driving feel that isn't adversely affected, the VF Engineering Supercharger Kit is one of the best options on the market. Included with every supercharger system is their custom proprietary VF.GIAC software that safely realigns all fueling and engine management parameters for optimal performance and long term drivability. Unlike many other options that are available, the VF Supercharger kit is designed to work with BMW's OEM parameters to minimize the likelihood of DTCs (Diagnostic Trouble Codes) and Check Engine Lights.

This 6.0 psi VF Engineering supercharger system is designed for simple bolt-on installation, remains fully OBD2 compliant, and can be installed in a single day, ready to run in approximately 8 hours. This kit is also non-intrusive and is fully reversible. 

The 6.0 psi manifold at peak boost was tested to be the optimal induction charge limit without aftercooling and offers max tourqe gains!

Upon ordering, you will be required to send your VIN number, ECU, and transmission type (auto or manual) to VF Engineering within 1 year of purchase for your software flash of the ECU.

This product is supported by a 1 year unlimited mileage warranty on the product only.

BMW Supercharger Kits can be found all over the internet, but who should you choose to go with? If you want to go to with a forced induction system and want reliability and a driving feel that isn't adversely affected, the VF Engineering Supercharger Kit is one of the best options on the market. Included with every supercharger system is their custom proprietary VF.GIAC software that safely realigns all fueling and engine management parameters for optimal performance and long term drivability. Unlike many other options that are available, the VF Supercharger kit is designed to work with BMW's OEM parameters to minimize the likelihood of DTCs (Diagnostic Trouble Codes) and Check Engine Lights.

This 6.0 psi VF Engineering supercharger system is designed for simple bolt-on installation, remains fully OBD2 compliant, and can be installed in a single day, ready to run in approximately 8 hours. This kit is also non-intrusive and is fully reversible. 

The 6.0 psi manifold at peak boost was tested to be the optimal induction charge limit without aftercooling and offers max tourqe gains!

Upon ordering, you will be required to send your VIN number, ECU, and transmission type (auto or manual) to VF Engineering within 1 year of purchase for your software flash of the ECU.

This product is supported by a 1 year unlimited mileage warranty on the product only.