BMW Engine Parts for BMW 6 Series E63 (2004-2010)

When we designed this catch we wanted to have the most function options available, the best separation method, and the easiest to service. The Turner engineered catch cans offer a pre-setup design based ion desired flow direction, however this does not limit you to this flow. The inner baffle orientation can be easily adjusted to flow in both directions in case you decide to move this catch can to a different vehicle. A 4 chamber system  baffle system inside the catch can was engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can. Having a closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation.

Our catch can was also designed with the idea that the cans fill level can easily be checked with a top mounted dipstick and an optional use bottom drain hole. The drain hole can be used with a valve and hose to be mounted at a lower area of the vehicle so when you're doing an oil change you can drain the catch can.

Features:

• 6061-T6 billet machined body, anodized black for lasting protection and appearance
• Strategically positioned 4 chamber baffle system maximizes oil / air separation 
• Knurled and black anodized oil dipstick makes inspecting oil volume of reservoir clean and simple
• Sealed with a pre-installed viton O-Ring
• Includes 2.5mm allen key to remove baffle plates for cleaning
• Engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can
• Closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation
• Optional use drain hole (valve and hose sold separately, watch for our model specific drain kits!)

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.

This is the current replacement for some BMW 6 and 8-cylinder engines built in the late 2000s and after. BMW has made numerous changes to ignition coil part numbers in recent years but has approved this part number to work in the vehicles listed below. It's listed as a replacement coil for N20, N55, and S55 engines. In March 2015 BMW approved it for N51/N52 engines. This part number replaces the previous BMW part number 12137594937 for the cars listed below.

Sold per coil. Includes boot and connector.

If you're noticing misfires, poor fuel economy, reduced engine performance, or ignition-related diagnostic trouble codes (DTCs), a failing ignition coil is likely the cause. Late-model BMWs, such as the E60 M5, E63 M6, and E64 M6, use a coil-on-plug ignition system, where each cylinder has its own coil and spark plug for efficient ignition. When a coil fails, the affected cylinder won't receive a spark and will misfire. Even if the misfire doesn’t trigger a DTC, you’ll still feel the difference in engine performance—rough idling, hesitation during acceleration, or a strong fuel smell. To avoid these issues, we recommend replacing your ignition coils every 40,000-60,000 miles.

The S85 engine uses a specialized ignition system called Ionic Current Control, which differs from traditional knock sensors. BMW engineers developed this system to more accurately detect pre-ignition and misfires in the high-revving, ten-cylinder S85. Instead of relying on conventional knock sensors, the system uses each spark plug to measure current after the power stroke, transmitting that data to the Ionic Current Control Unit (ICC). This allows for precise monitoring of combustion events. To support this, the S85’s ignition coils are specially designed with a modified “pencil” shape and lack a Zener diode in the secondary winding, allowing for accurate current measurements without triggering fault codes in the engine control unit (DME). These ignition coils are manufactured to the exact specifications of the OE Ionic Current Control-compatible ignition coil, and will not trigger ignition-related fault codes in the DME.

Bavarian Autosport ignition coils are engineered for reliability, delivering a consistent, long-lasting spark. These high-quality OE replacement coils are specifically designed for your S85-powered E60 M5, E63 M6, or E64 M6. Constructed with durable, heat-resistant plastic and featuring premium rubber spark plug boots, each boot is pre-lubricated with dielectric grease to ensure smooth installation and prevent corrosion.

Whether you're fixing misfires, replacing a faulty coil, or performing preventative maintenance on your S85 ignition system, trust Bavarian Autosport ignition coils for a dependable, lasting repair.

FEATURES:

Durable, heat-resistant plastic: Built to withstand extreme temperatures and harsh driving conditions for long-lasting durability. Pre-lubricated, high-quality rubber boots: Prevent moisture and corrosion while ensuring smooth, easy installation. OE-quality construction: Meets or exceeds original equipment standards for perfect fit, reliable performance, and effortless installation.

The oxygen sensor is vital to the performance and drivability of your car. The engine computer relies on data from the sensor to make adjustments in engine efficiency and performance. When your BMW oxygen sensor fails, the computer can no longer sense the air/fuel ratio, so it ends up guessing -- resulting in poor performance, poor gas mileage, and increased pollution. Make sure your BMW engine performs as it should, and doesn't use more fuel than it needs to, by simply changing your oxygen sensor today. There is no lifespan on O2 sensors but there are several fault codes that indicate a failed sensor (O2 monitoring, cat efficiency, O2 heating circuit, O2 readiness, and others). The O2 sensor is heated and has a self-calibration feature so once you get the codes or feel performance has suffered, a new sensor is a good starting point to get you back to peak performance.

This is a Bosch O2 sensor - also known as a Lambda probe. Bosch is an OEM supplier to BMW.

Position: after the catalytic converter (post-cat).

This item fits the following BMWs:
2008-2013 E90 E92 E93 BMW M3 Sedan, Coupe, Convertible

The Foxwell i70BT is your solution for a tablet diagnostic scanner that will elevate your level of diagnostics without breaking the bank.  This unit is one step above the standard i70, and we'll explain why below.  This heavy-duty tablet can withstand any work you put it through and will find its place in any garage and/or shop.  The i70 is unlocked with almost any manufacturer you will interact with and is pre-loaded to be compatible up to years 2019/2020 - plus 3 years of free updates to stay relevant for years to come. With dozens of features, 35 additional maintenance functions, and backed by our LIFETIME REPLACEMENT program, this scan tool will get the job done right, every time.

i70BT vs i70:

• *NEW* Fox Link I: i70BT can wireless connect to your vehicle AND supports CAN/FD protocol
• *NEW* Bi-directional control on i70BT
• i70BT is more up-to date off the bat (vehicles 2020/2021, and still including 3 years of free software updates to stay up-to-date)

Why the i70BT?

First, the Hardware:

• Display: 7" color LCD Screen that is daylight-readable
• Memory: 1 GB DDR3L
• Storage: 32 GB SSD
• Connection: Wireless VCI
• Battery: 4000 mAh

What Are Its Standard Features?

• *NEW* Wireless Connection with Foxlink I.
• *NEW* Supports CAN/FD protocol.
• *NEW* Bi-directional control.
• Loaded with the latest models on most cars 2020/2021 and with 3 years of free software updates.
• Compatible with latest models, including cars, SUV's, Minivans, and light duty trucks.
• Gets access to power-train, chassis, and body systems.
• Identifies vehicle quickly and easily with automatic VIN reading.
• Auto Scan function scans vehicle in just a few seconds.
• Reads and clears diagnostic trouble codes.
• Supports the most commonly required service features like brake deactivation, service resets and transmission adaptations.
• Supports ABS bleeding and IMMO functionalities
• Runs on latest Android operating system.
• Screen is usable with gloves.
• FRM testing for BMW/MINI.
• Audi maintenance mode.

How about the Coding and Graphing?

• Views live vehicle sensors data in a text, graph and gauge formats and allows you to focus on any suspicious data.
• Merges multiple interactive sensor graphs, providing you with the most comprehensive and functional look at live data.
• Live data self-learning and alarms when data is over range.
• Records and plays back live data logs to catch intermittent faults.
• For coding features, check out the i70Pro (ES#3698691)!

What Else Makes It Stand Out?

• One touch update via Wi-Fi lets you always have the latest bug fixes, new vehicles, and functionality at your fingertips.
• Unique debug logging feature allows for quicker and more accurate fixes for diagnostic troubles and bugs.
• Instant support available from Foxwell's technical team by TeamViewer remote control

Kit Includes:

• i70BT Main Unit
• VCI Dongle
• USB-C Cable 
• USB Charging Adapter
• Quick Start Guide
• Warranty Card 
• User Manual

For more information about this tool, visit: https://www.foxwelltech.us/product-detail-737.html

For further information past this, please contact Foxwell sales team at: [email protected]

For technical support, please contact: https://www.foxwelltech.com/support/ticket/

Spark Plug Gapper Tool BMS Billet is essential for accurately adjusting the gap of spark plugs. This precision tool ensures that each plug is set to the exact specifications required for optimal engine performance. Made in the USA, it features a 12mm plug thread size, making it suitable for a wide range of applications.

• Precision Adjustment: Allows for accurate gap adjustments to ensure optimal spark performance and engine efficiency.
• Speed and Efficiency: Streamlines the process of gapping plugs while maintaining high precision, saving time and effort.
• High-Quality Construction: Crafted from billet materials for durability and reliability, ensuring long-term use.
• Lifetime Replacement Program: Comes with a lifetime replacement guarantee, reflecting confidence in the tool's quality and performance.

Upgrade your spark plug maintenance with the Spark Plug Gapper Tool BMS Billet for a reliable and precise solution.