BMW X Series E70 (2007-2013)

Replace the flimsy plastic bleeder screw used in the coolant expansion tank or in one of the cooling system hoses with this high quality, durable, aluminum bleeder screw. The stock plastic screw can deform over time due to heat or even regular use. We have even seen the head of the screw snap off, leaving the threaded body stuck in the expansion tank. This aluminum screw will help to prevent sudden failure of the bleeder screw, which can result in immediate overheating of the car.

ECS Tuning's Aluminum Coolant Bleeder Screw replaces Genuine BMW Part Number 17111712788

Enhance your BMW's performance with the upgraded BAV Ignition Coil, designed to boost firepower and optimize engine efficiency. These coils boast modified core windings for a faster, more efficient burn, resulting in increased torque at lower RPMs and heightened horsepower in the upper range. While improvements depend on your engine's condition, these coils ensure noticeable enhancements in performance and potential fuel economy benefits.

Product Benefits:

Improved engine firepower and efficiency
Increased torque at lower RPMs
Enhanced horsepower in higher ranges
Potential improvement in fuel economy
Set of six for complete BMW Cooper replacement

This caliper bushing kit will eliminate flex caused by weak rubber caliper bushings. As the brake pedal is pressed the caliper grabs the rotor and twists on its mounting bushings. The rubber bushings allow the caliper to deflect and twist which affects pedal feel and results in uneven pad wear. These solid brass bushings will not twist or deflect so your calipers can squeeze the pads evenly on both sides of the rotor (sort of like what multi-piston big brakes do). This will give you much longer pad life and a more consistent pedal feel. This is the most complete kit we have ever sold with stainless steel caliper slide bolts, o-rings, and new dust boots. Unlike other kits, these bushings are pressed into the caliper and will not shift or slide on their own.

Installation is straightforward: remove the old rubber bushings and press in the new brass bushings (we recommend special tool 003326ECS03). High temp caliper grease or anti-seize is required. The new bushings include an inner o-ring that helps trap grease on the slide bolt, reducing friction and wear.

***Click here for installation instructions*** 

***Click here for the installation tool***

For most models with floating calipers. Fits the rear of E90/2 and E60, but for the front you'll need the kit found here. Does not fit E30 models with Girling calipers, but is compatible with Ate calipers. 

Enhance wheel replacement efficiency on your BMW with a stud conversion kit, facilitating quicker and easier wheel changes. This comprehensive kit includes:

• Conical Seat Lug Nuts (20)
• 75mm Wheel Studs (20)

The installation of these studs provides a permanent wheel-hanging solution, saving time and reducing hassle during wheel changes. By simply screwing in the supplied studs, you'll be ready to go.

Benefits of using wheel studs instead of wheel bolts:

• Some racing regulations mandate wheel studs for enhanced wheel-to-hub contact, ensuring added safety.
• Wheel studs accommodate various spacer widths, eliminating the need for custom bolt lengths when using spacers.
• Simplifies wheel installation; the studs act as wheel hangers while nuts secure the wheel in place.
• Reduces wear on wheel hubs as wheel studs remain in the hub, unlike constantly removed and installed wheel bolts.
• Facilitates quick and easy tire changes as wheel studs stay in place.

Note: Use thread-locking compound during installation and torque studs to 15Nm for optimal performance.

Upgrade your BMW's wheel system with this stud conversion kit for improved convenience and functionality.

Upgrade your stock oil cooler thermostat for improved performance. Swap your factory 110-degree Celsius thermostat for a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly, unlike thermostat bypass kits.

Kit contents:​

Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

Ensure your driving machine's peak performance with regular maintenance. Turner Motorsport offers a comprehensive service kit to keep your BMW in top shape. With varying oil change intervals based on driving habits, this kit includes:

• Seven Liters of BMW Synthetic Engine Oil
• Engine Oil Filter
• Oil Drain Plug Gasket (Included with filter kit)

For optimal results, we recommend an oil change every 10,000 miles, or every 5,000 miles for aggressive or city driving. Trust Turner Motorsport to provide the quality and precision your BMW deserves.

Your floor jack is universal but it doesn't have to be with this adapter! Most newer BMW jack pads have an open recess inside that this adapter fits into. It's a rectangular peg for a rectangular hole. This gives the jack a much more rigid connection and almost impossible for the jack or pad to slip. You will never have to worry about scratching your rocker panels or jacking from the wrong spot - the positive connection ensures you are always lifting from the correct location. This adapter is one of those small hidden gems that you can't live without! 

Made of black anodized aluminum for added strength and corrosion resistance, the adapter fits the head of most hydraulic floor jacks, including the Schwaben Low Boy.

Compatible with most BMW jack pads for chassis E39 and up. Retrofitting jack pads is common, especially on E36/Z3 models.

Enhance your BMW's performance with the upgraded BAV Ignition Coil, designed to boost firepower and optimize engine efficiency. These coils boast modified core windings for a faster, more efficient burn, resulting in increased torque at lower RPMs and heightened horsepower in the upper range. While improvements depend on your engine's condition, these coils ensure noticeable enhancements in performance and potential fuel economy benefits.

Product Benefits:

Improved engine firepower and efficiency
Increased torque at lower RPMs
Enhanced horsepower in higher ranges
Potential improvement in fuel economy
Set of eight for complete BMW Cooper replacement

Liqui Moly is an official sponsor of Turner Motorsport. We work closely with Liqui Moly to ensure your BMW is receiving optimal lubrication!   Select your vehicle to make sure you are viewing the best Liqui Moly options for your application. 

Includes:

• 7 Liters of Longtime High Tech Engine Oil 5w-30
• Hengst Engine Oil Filter
• Oil Drain Plug & Gasket

Longtime High Tech engine oil is designed to provide the highest amount of engine protection as well as fuel savings and reduced oil consumption possible. Using proprietary blends of base oils and the latest additive technology, this oil will ensure smooth running gasoline and diesel engines in both high and low temperatures. Other amazing benefits include: optimum oil pressure at all speeds, rapid oil delivery at low oil temperatures, high shear and aging stability, turbo and multi-valve compatibility, and long service life.

Properties:

• Smooth engine running characteristics
• Long engine service life due to exceptional protection against wear
• Rapid oil delivery at low temperatures
• Optimum oil pressure at all engine speeds
• Premium lubrication reliability at high and low temperatures
• High shear and ageing stability
• Reduces fuel consumption and pollutant emissions
• Outstanding engine cleanliness
• Tested with catalytic converters and performance proven with turbochargers
• Miscible and compatible with commercially-available engine oils

Approved for the following specifications:

• ACEA C3
• API SN / CF
• BMW Longlife-04
• MB-Approval 229.51
• VAG 502.00 / 505.00

Recommended for the following specifications:

• ACEA A3 / B4
• MB 229.31
• VAG 505.01

Liqui-Moly is a German chemical company that offers top of the line engine oils, additives, and car care products that are designed to extend the life of your engine and ensure the best lubrication and cleanliness off engine and transmission components possible. With more than 50 years of experience and reviews across the world from magazines and race teams, Liqui-Moly proves time and time again why they are one of the most innovative lead forces of performance automotive chemicals in the world.

Upgrade your stock oil cooler thermostat for improved performance. Swap out your existing cover with ease, replacing it with a durable billet cover. Upgrade from your 110-degree Celsius thermostat to a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly unlike thermostat bypass kits.

Kit contents:

Billet thermostat housing cover
Replacement gasket
Hardware
Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

Upgraded replacement for your crankcase vent hose P#11127584128 featuring upgraded silicone, stainless steel clamps, and new OE connectors and seals.

Enhance your BMW N55 engine with our Silicone Crank Case Vent Hose, a premium replacement for the fragile, failure-prone factory hose. Over time, the stock plastic hose deteriorates due to constant exposure to heat and oil, leading to cracks and leaks. Our solution? A high-quality silicone hose engineered for superior durability and long-term reliability.

To further enhance performance, we’ve lined the hose with fluorosilicone, providing exceptional resistance to oil and chemical degradation. Designed in-house using advanced CAD modeling and 3D scanning, this hose offers a precise OEM fit while eliminating the common weaknesses of plastic construction.

Each kit includes stainless steel hose clamps for a secure, hassle-free installation. Whether you’re replacing a worn-out CCV hose or upgrading for added peace of mind, this premium solution ensures your BMW N55 runs smoothly and efficiently for years to come.

Features:

Arrives preassembled with new OE fittings and seals
Direct OEM Fit – Retains factory hose dimensions while eliminating reliability issues.
High-Performance Silicone – Resists heat-related wear for long-lasting durability.
4-Ply Fluorosilicone Lining – Superior protection against oil and chemical exposure.
Stainless Steel Clamps Included – Secure installation and extended service life.
Give your BMW N55 the reliability it deserves—upgrade to the ECS Tuning Silicone CCV Hose today!