Showing 1835 results for ""

The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice. 

Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.

While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.

Kit Includes:

• 1x Aluminum Crank Bolt Capture
• 8x Fasteners Gr. 12.9

This part fits the following BMWs:
2006-2013 N54 

Hardware to replace the coarse-thread screws originally used to mount components to the plastic valve cover.

Factory and aftermarket valve covers are made from plastic and use coarse-thread screws designed specifically for plastic. When upgrading to an aluminum valve cover, this hardware can no longer be used, as it will not properly thread into aluminum.

This kit includes all necessary hardware required to mount the factory components onto your upgraded aluminum valve cover.

Included Hardware:

2 × M6 × 1.0 × 40 mm bolts

4 × M6 × 1.0 × 20 mm bolts

2 × M6 × 1.0 × 12 mm bolts

Featuring silver fine wire center electrode - Superior ignition ability increases engine power!

Although these come pre-gapped we highly recommend double checking the plug gap upon receiving them and adjusting to your vehicle's individual needs.
For the N55/S55, these plugs are 2 Steps Colder, while for the N54 they are 3 Steps Colder.

Note that BMW Spark plugs require a special 12 point 14mm thin walled socket. We have several options available in our catalog that will help you get your spark plugs changed. The BMW part number for the tool is 83300495560, but we recommend the Schwaben brand T#373727 that won't cost you an arm and a leg.

Brisk Silver Racing Spark Plugs are the best solution for high performance and racing engines. Silver Spark Plugs provide many unique and beneficial characteristics, Silver is taking spark plug technology to a whole new level, here are many reasons why our Brisk Silver Racing Spark Plugs are beneficial for your engines performance. Silver is the best conductor of any metal! It conducts 560% more electricity & 481% more heat than Platinum, and 276% more electricity & 177% more heat than Iridium.

Silver spark plug electrodes transfer electricity & heat better than any other spark plug material resulting in the most powerful spark! This is beneficial for a full complete combustion of the available fuel and air in the combustion chamber, combustion efficiency creates horsepower gains.

Key Benefits and Applications of Brisk Silver Racing Spark Plugs:

Silver is the best Electric and Heat Conductor - the best material for performance and racing spark plugs
Superior Ignition Ability Increases Engine Power Lower Required Supplied Ignition Voltage
Good Resistance to Fouling and Easier Starts
Race Engines and Engines with Hard to Ignite Fuels
Supercharged / Turbocharged / Nitrous engines
Excellent for Total Loss Ignition Systems
Excellent Spark Plug Choice for any Vehicle, Stock or Modified, even for High Mileage Vehicles and Vehicles With Oil Consumption Problems
Spark Plug Specs:

12mm thread
1.05"(26.1mm) reach
14mm Bi-Hex
gasket seat
non-projection tip
resistor
Silver center el.
cut-back ground electrode
* Replacement for NGK SILZKBR9F8S (BMW# 12120042724)
* One heat range colder than NGK 97506 SILZKBR8D8S

When it comes time to change your spark plugs, you may wonder about colder stepped spark plugs as many others have. Colder spark plugs work by pulling more heat out of the engine's cylinders (making them "colder") and dissipating it into the engine's head, which is then cooled by the cooling system. Depending on how you have your engine built, these could be a great addition! Colder plugs can help prevent engine knock and prevent the tip of the spark plug from melting or misfiring.

There are two rules that most people tend to go by when deciding on which spark plugs to buy:

The first rule of thumb is that with every 100 horsepower added, you should run spark plugs that are a step colder than your stock plugs. This is generally accepted across the motorsports community but unfortunately isn't always the most accurate measurement of when you will need colder plugs.
The second rule is to go a step colder any time you massively alter cylinder temperatures by adding forced induction to an NA engine, by increasing compression ratio, after altering timing in a major way, or by changing fuel types to something with a higher octane rating such as racing fuel.
Adding spark plugs that are a step colder outside of these conditions, with no real change to the engine, can actually hurt more than help by leading to spark plugs fouling quicker than normal and by making the car harder to start in cold weather conditions.

CTA Tools - Spark Plug Gapper is an essential tool for accurately setting and measuring spark plug gaps, ensuring optimal engine performance. This precision tool is designed for both professional and DIY mechanics, providing reliable gap adjustments for a variety of engine applications.

• Versatile Measurement Range: The ramp gauge measures gaps from .020 to .100 inches (0.50 to 2.5 mm), accommodating a wide range of spark plug specifications.
• Precision Engineering: Engineered to deliver accurate gap settings, improving engine efficiency and performance.
• Made in the USA: Crafted with high-quality materials to ensure durability and long-lasting performance.
• Easy to Use: Simple design makes gap adjustments quick and straightforward, enhancing convenience in any workshop or garage setting.

Upgrade your toolset with the CTA Tools - Spark Plug Gapper to achieve precise spark plug gaps and optimize your engine’s performance.

Spark Plug Gapper Tool BMS Billet is essential for accurately adjusting the gap of spark plugs. This precision tool ensures that each plug is set to the exact specifications required for optimal engine performance. Made in the USA, it features a 12mm plug thread size, making it suitable for a wide range of applications.

• Precision Adjustment: Allows for accurate gap adjustments to ensure optimal spark performance and engine efficiency.
• Speed and Efficiency: Streamlines the process of gapping plugs while maintaining high precision, saving time and effort.
• High-Quality Construction: Crafted from billet materials for durability and reliability, ensuring long-term use.
• Lifetime Replacement Program: Comes with a lifetime replacement guarantee, reflecting confidence in the tool's quality and performance.

Upgrade your spark plug maintenance with the Spark Plug Gapper Tool BMS Billet for a reliable and precise solution.