BMW Engine Parts for BMW 1 Series E82 (2008-2013)

If you're experiencing hard starting, flaky charging, or other electrical issues, your engine ground strap may be the culprit. On E9X BMWs, the engine ground strap is a thin, non-insulated cable that spans from the left engine mount arm to the frame horn. Despite the seemingly simple nature of this part, on older cars, it is known to cause massive headaches. Due to its non-insulated design, years of exposure to water, dirt, and road salt will cause the wire to corrode, ultimately leading to complete failure. A break in this cable will cause an open circuit, resulting in issues with the vehicle's electrical system and potentially leading to a no-start condition.

To solve this issue, ECS has engineered an exact-fit, upgraded ground strap for your E9X BMW! Unlike its OEM counterpart, this design features insulated, large-gauge copper wire for dependable conductivity and long-lasting durability. Additionally, factory-style lugs are zinc-coated, crimped, and soldered, ensuring protection against corrosion and oxidation.

Whether you're replacing a visibly corroded strap or proactively preventing failure, this solution from ECS is sure to provide lasting performance and protection.

FEATURES

Direct-fit replacement and upgrade for RWD E82/E88, E84, and E9X applications Solves intermittent grounding issues caused by aging OEM straps Clean, stealthy design that fits seamlessly in factory engine bays Factory length and lug orientation for drop-in fitment 2 AWG tinned copper cable for excellent conductivity and corrosion resistance Zinc-coated lugs, crimped and soldered to resist moisture and oxidation Black UL1015-grade insulation withstands oil, heat, and abrasion Discreet ECS label for a clean, OEM+ look Replaces OEM part numbers 12427549393, 12427795404, and 12427790559.

The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice. 

Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.

While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.

Kit Includes:

• 1x Aluminum Crank Bolt Capture
• 8x Fasteners Gr. 12.9

This part fits the following BMWs:
2006-2013 N54 

Continental is the OEM supplier for the stock serpentine accessory belt on your N52 engine.?Over time, accessory belts begin?to wear out and crack. This can lead to the belt slipping, squeaking, or even snapping. Replace your belt on a regular basis to ensure you don't end up stranded on the side of the road with a dead battery or over heated engine due to a bit of simple overlooked maintenance.

Fits the following BMW chassis:
E90 E82/8 E60 E70 E83 E63/64

This sensor monitors the position of the Valvetronic eccentric shaft and feeds data back to the ECU. The common issue with this sensor is that it gets contaminated with oil and fails. It doesn't give a fault code or check engine light, however. What you would notice is sluggish driving, hesitation, poor performance, jerky shifts from an automatic, and other drivability issues. These types of issues are typically diagnosed as ignition coils (which are their own issue altogether) but this sensor may also be faulty.

The eccentric shaft sensor is located at the front of the cylinder head and is only accessible with the valve cover off. It's easy to check for oil by removing the engine trim cover (the outer cover with the BMW roundel), unplug the sensor, and look inside. If oil is present inside, or even on the valve cover itself, the sensor is likely contaminated or ready to fail. You can wipe or clean the oil from sitting inside the sensor but it will come back.

If you're planning this job make sure you have our Valve Cover Overhaul Kit, which includes a new seal for the eccentric sensor as well as the rest of the valve cover and Valvetronic gaskets. You can add the valve cover set from the options below.

OEM VDO is one of the largest OE providers in the world, supplying numerous vehicle brands, including BMW, with many of their genuine parts that build the vehicle before they ever reach the car lot. Entrusted by many of the top names in automotives and with their proven history of reliability, it makes all of us here at Turner confident that their line of OEM replacement parts are a perfect option to restore your vehicles original operation and performance. The same great quality or higher than Genuine BMW parts at a lower cost.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2008+ E82 BMW 128i
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive - Coupe
2007-2013 E93 BMW 328i - Convertible
2006-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive
2010+ F07 BMW 535i GT, 535i xDrive GT, 550i GT, 550i xDrive GT
2011 F10 BMW 528i
2006-2010 E83 BMW X3 3.0i X3 3.0si
2011 F25 BMW X3 xDrive28i
2007-2010 E70 BMW X5 3.0si X5 xDrive30i
2006-2008 E85 BMW Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive30i