BMW Engine Parts for BMW 1 Series E82 (2008-2013)

Upgrade your stock oil cooler thermostat for improved performance. Swap your factory 110-degree Celsius thermostat for a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly, unlike thermostat bypass kits.

Kit contents:​

Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

Every 60-80,000 miles, we recommend replacing your spark plugs to ensure your ignition system is running optimally. Over time carbon can build up around the head of the spark plug and decrease spark strength and effectiveness, leading to weaker fuel mixture detonation, misfires, and potential check engine lights. To prevent this, have put together our High-Performance Ignition Service Kits. These kits include new Bav Auto High-Performance Ignition Coils, new spark plugs, dielectric grease, and a BMW spark plug service label to keep track of when your spark plugs were replaced.

Bav Auto's Ignition coils feature core windings that have been modified to increase firepower and promote a faster, more efficient burn. This gives your BMW/MINI increased torque in the lower range of RPM and more horsepower in the upper range. Exact improvements depend on the current condition of your engine, but you'll definitely feel the difference. They'll also improve your fuel economy.

From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.

As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Elevate your custom installation with the ECS -10AN O-Ring Boss fitting, a crucial component that connects your ECS Tuning Catch Can to a 3/4" ID hose. This fitting simplifies your plumbing setup, ensuring a seamless solution.

Featuring a pre-installed Viton O-ring, this fitting is engineered for excellence, providing a leak-proof seal that resists the effects of oil and fuel exposure, guaranteeing long-term durability.

The 3/4" nipple is thoughtfully designed with barbs to secure hose position effectively, minimizing the risk of hose disconnection. Keep in mind that clamps and hoses are available for separate purchase. These fittings are sold individually, with most installations requiring a pair of them.

Ensure proper sealing when installing the turbos on your N54.

Kit includes:

• 16 - ASA M7x39 studs
• 16 - Flange nuts
• All required gaskets and o-rings
• Water pump install hardware
• Replacement vacuum hose
• T-bolt clamps

Helpful hints:

For complete installation instructions, refer to Haynes Service Manual (T#193950).

Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal.

If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side.

To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well.

Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced.

Torque specs:
Bracket to cylinder head: 9Nm
Coolant supply line to crankcase: 9Nm
Coolant return line to crankcase: 8Nm
Coolant return line to turbo: 8Nm
Coolant supply line to supply line: 8Nm
Exhaust manifold heat shield: 8Nm
Oil supply line to crankcase: 20Nm
Oil pressure line to turbo: 8Nm
Oil return line to crankcase: 8Nm
Oil return line to turbo: 8Nm
Turbo manifold to head: 20Nm

This kit includes every thing needed to replace your rod bearings.

Kit includes

Upper and lower WPC-treated rod bearings Hardware Oil filter BMW TwinPower Turbo Oil Oil pan gasket RedLine assembly lube