BMW Engine Parts for BMW X Series E84 (2013-2015)

High performance ignition kit for your N54/N55 featuring colder stepped spark plugs, Turner high performance ignition coils and grease to make sure you have no issues at your next maintenance interval! Included plugs are one Step colder for N55, Two step colder for N54.

Our BMW ignition coils are designed with performance and efficiency in mind. An engine needs 3 main components to run (Air, Fuel, Spark.) Turner ignition coils are modified to increase energy output; more energy output results in a faster, more efficient and consistent burn to make sure your fuel is being utilized to its maximum potential. Our signature Turner ignition coils feature a blue housing that give your engine the performance and aesthetic your looking for.

Ignition coils should be changed every 40,000 - 60,000 miles and are an important maintenance item due to the essential role they play in your engines health, performance and efficiency. Choose Turner Ignition Coils to keep your engine running strong and healthy.

Features and Benefits:

Increased performance
New spark plugs and grease
Direct fitment
Signature Turner Blue ignition coils

Due to weak plastic construction, the factory plastic crankcase ventilation breather hose is known to fail. After years of exposure to piping-hot engine bay temperatures and chemical-laden oil vapors, the corrugated plastic tubing can crack, crumble, or fail altogether.

We set out to bulletproof your N20 PCV system with a durable silicone breather hose, designed to provide a comprehensive upgrade and permanent replacement for the factory plastic hose. By replacing the flimsy, heat-hardened OEM plastic hose with a four-ply fluorosilicone hose, you'll experience peace of mind knowing your N20 is free from the inevitable return of oil leaks, vacuum leaks, and drivability concerns that would have been.

This breather hose is found at the front of the engine, and is used to connect the inlet pipe to the valve cover. It replaces OEM part number 11127588417.

Features:

Silicone construction ensures a durable replacement that is sure to outlast OE plastic
Designed as a direct replacement for the factory breather hose
Retains heating function and OE electrical connector
Design:

Four-ply wire-reinforced fluorosilicone hose is designed to resist degradation due to exposure to oil vapors
O-rings are pre-installed in OE connectors for a lasting seal
Includes pre-installed zinc-coated hose clamps for durability and corrosion resistance
Product Development:

Our Silicone PCV Hose Upgrade was designed, engineered, tested, and quality inspected by our Research and Development team in our Wadsworth, Ohio, facility. We strive for the highest level of precision and quality through leading-edge product development technology, including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modelling, rapid prototyping utilizing our in-house 3D printer, and rigorous long-term product testing.

Full carbon fiber intake to increase flow, performance and aesthetics! Dual inlet design for maximized air flow while retaining the OEM+ fitment.

The most common N55 intake utilizes a short plastic tube and oversized cone filter; it is your job to have better taste than the common N55 owner. This carbon intake changes the whole image of the N55 engine while maintaining a flow of cool air and added induction noise. With a dual inlet design the engine bay retains its functionality while adding a second inlet to provide your engine with improved air flow and sound. To ensure the engine gets the coolest air possible the second inlet is located in the "sweet spot" on the cold side of the engine for the lowest intake air temps and most air flow possible. The cone filter features a bellmouth velocity stack filter that creates the satisfying flutter after letting of the throttle.

Our Turner Carbon Fiber Intakes start with a 3D scan of the factory intake and engine bay. Engineers use the 3D imaging of the chassis to design the intake in SolidWorks modeling software. Using a Flow Bench, the Intake is then airflow tested against the factory intake, to ensure optimal airflow improvement against stock. The final product is a beautiful and functional Carbon Fiber Intake, CAD designed for perfect integration with the OEM inlet ducting and stock mounting locations and proven to flow better than factory.

Key Benefits:

Increased flow over the factory intake
Carbon fiber airbox and intake tube with gloss clear coat for UV protection
CAD-Designed for perfect Integration
Custom high flow air filter specially designed to to pair with the carbon fiber airbox
Kit Contents:

Carbon Intake Tube
Full Carbon 2 Piece Airbox
Bellmouth Velocity Stack Cone Filter
Billet Turbo Inlet Adapter
Silicone Coupler
Hardware For Installation
Design:

- Carbon Fiber Intake Tube

Carbon inlet tube featuring a smoother interior without corrugations for a smooth flow path.
Integrated carbon flange allows secure mounting of the tube to the carbon air boxes.
Intake tube is manufactured using 2x2 twill weave carbon fiber for a great look in the engine bay.
Gloss finish clear coat for UV protection.
4-ply reinforced silicone coupler and 6061-T6 black anodized aluminum flange that utilizes the factory o-ring and retaining clip.
- Air Box

Carbon fiber airboxes are manufactured using 2X2 twill weave carbon fiber and protected with a gloss finish clear coat for UV resistance to match the intake tube.
Air box mounts in stock location with supplied hardware.
- Air Filter

Conical hi-flow reusable air filter; featuring 8 ply oiled cotton gauze construction to maximize filtration efficiency.
Bellmouth (velocity stack) filter flange inlet to reduce turbulence in order to maximize flow.
Product Development:

Turner N55 Intake System was designed, engineered, tested and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer and rigorous long term product testing. Performance data metrics are collected utilizing Mustang AWD 500 SE in ground dyno and in-house Superflow SF-750 Flowbench.

Fitment:

E82 135i N55
E88 135i N55
E84 X1 35i
E90 335/xi N55
E92 335/xi N55
E93 335/xi N55

If you're experiencing hard starting, flaky charging, or other electrical issues, your engine ground strap may be the culprit. On E9X BMWs, the engine ground strap is a thin, non-insulated cable that spans from the left engine mount arm to the frame horn. Despite the seemingly simple nature of this part, on older cars, it is known to cause massive headaches. Due to its non-insulated design, years of exposure to water, dirt, and road salt will cause the wire to corrode, ultimately leading to complete failure. A break in this cable will cause an open circuit, resulting in issues with the vehicle's electrical system and potentially leading to a no-start condition.

To solve this issue, ECS has engineered an exact-fit, upgraded ground strap for your E9X BMW! Unlike its OEM counterpart, this design features insulated, large-gauge copper wire for dependable conductivity and long-lasting durability. Additionally, factory-style lugs are zinc-coated, crimped, and soldered, ensuring protection against corrosion and oxidation.

Whether you're replacing a visibly corroded strap or proactively preventing failure, this solution from ECS is sure to provide lasting performance and protection.

FEATURES

Direct-fit replacement and upgrade for RWD E82/E88, E84, and E9X applications Solves intermittent grounding issues caused by aging OEM straps Clean, stealthy design that fits seamlessly in factory engine bays Factory length and lug orientation for drop-in fitment 2 AWG tinned copper cable for excellent conductivity and corrosion resistance Zinc-coated lugs, crimped and soldered to resist moisture and oxidation Black UL1015-grade insulation withstands oil, heat, and abrasion Discreet ECS label for a clean, OEM+ look Replaces OEM part numbers 12427549393, 12427795404, and 12427790559.

Stainless steel filtration is not a new technology but is quickly gaining popularity in the automotive segment. With the ability to filter down as small as a paper filter element with the ability to be washed and reused!

The K&P Engineering filter element is made from medical grade, type 304 stainless steel micronic filter cloth to provide unmatched protection against oil contamination and resultant engine damage. A one inch square of this material flows an incredible 1.9 gallons of oil per minute at only 1 PSI pump pressure. The adhesive used in the filter assembly process is good to 600 degrees Fahrenheit, far above normal engine operating temperatures. A super strength nickel-plated neodymium rare earth magnet is installed in the top of the element for magnetic pre-filtering of the oil. The sophisticated bypass is engineered for proper differential pressures and consistent operation, delivering a greater percentage of filtered oil while being very easy to clean. The twist lock design assures positive filter element placement and allows for easy disassembly, inspection, and cleaning. The quad-ring gasket doubles the seal between the filter and the engine. Finally, the filter housing is carved out of solid 6061T6 billet aluminum, which not only looks trick but aids in dissipating heat.

K&P Engineering manufactures stainless steel filters for a vast array of engines around the world. Staying at the forefront of design and testing allows this company to offer a top tier product for your European vehicle.

Features:

• Consistent filtering across entire filter surface
• Superior ASTMF316 filtration performance
• Magnetic Prefiltering
• Progressive rate bypass combined with high flow characteristics of the filter media avoids unfiltered oil bypassing the filter during cold startup and high rpm
• Easy inspection of engine contamination
• Proven in Motorsports, Military and Aerospace applications for years. Technology is FAA approved for use in aircraft. 

At regular oil changes, clean to K&P's specifications for continued used - a true lifetime filter.

This part fits the following BMWs:
2012+ F30 3 Series Sedan 328i 328iX 328i 328iX 335i 335iX 
2006 - 2013 E9X 323i 325i 325xi 328i 328xi 330i 330xi 335i 335xi
2010 - 2016 F10 5 Series Sedan 528i 528iX 530i 535i 535iX 
2003 - 2006 E60 Sedan 525i 525xi 530i 530xi 
2007 - 2010 E60 528i 528xi 535i 535ix 
2009 - 2016 E89 Z4 Roadster Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i 
2014+ F22 2 Series Coupe 228i 228iX M235i M235iX
2007 - 2013 E88 1 Series Convertible 128i 135i
2008 - 2013 E82 1 Series Coupe 128i 135i 135is 1M Coupe
2012 - 2013 E70 X5 xDrive35d X5 xDrive35i
2007 - 2011 E70 X5 3.0sd X5 3.0si 

This is a complete plug and play solution to replace your stock Low-Pressure Fuel Pump (LPFP) with a new E85 certified bucketless assembly.

This solution provides up to 25% more flow than our standard Stage 2 LPFP upgrade and up to 150% more flow than the stock pump.  

This pump will support up to 550whp running 85% ethanol and 600whp running 50% ethanol. 

The Stage 2 bucketless kit includes the following:

• • A custom anodized billet fitting for the pump output and stock fuel line connection.
  • Our custom billet aluminum anodized bracket for the pump and float assembly
  • Two cotter pins to secure your float assembly
  • A new E85 compatible Walbro 450 pump
  • Spare vent tube clip
  • A new Walbro filter

If you still need more flow, the Stage 3 upgrade is also available and can be added to your Stage 2 bucketless pump.

The Stage 3 upgrade kit includes:

• • A complete plug and play solution by simply adding the secondary module
  • Our custom billet aluminum fitting to run both pumps in parallel
  • A new E85 compatible Walbro 450 pump
  • Wiring harness for the secondary pump
  • Spare vent tube clip
  • A new Walbro filter

• Recommended accessories:
  • Lock Ring Removal Tool
  • Hobb's switch 
     
• NOTE: These kits include a basic filter assembly.  When using this filter, running the vehicle under low fuel conditions can cause fuel starvation issues. If you do hard straight line accelerations when you have less than 1/8 tank of fuel, we would recommend running our standard Stage 2, 3, or Stage 4 pump.  In addition, if you intend to use this for road course applications, you may see starvation issues when running less than a half tank and doing long high G right turns.  Again for those applications we'd recommend one of our standard pump applications.