Select Vehicle
BMW
Mini
Purpose
Category
-
Vanos System
Create an account to be able to build Wish Lists.
Please ensure your correct model is selected
A common cause of check engine light and limp mode after running the car hard. Restarting the car commonly clears the code and/or limp mode.
Two different problem codes, 2A87 "Outlet-Vanos variable cam control test" and "2A82 Inlet-Vanos variable cam control test", are thrown indicating the possibility of various VANOS-related problems. If a solenoid valve needs to be replaced, this part is appropriate for both situations, outlet and inlet.
Located at the end of the pressure limiting valve. This prevents contaminants from damaging the VANOS system.
GENUINE BMW VANOS FILTER CARTRIDGE
We sell this part with the required gasket Here
Feeds oil to the VANOS unit from the oil filter housing.
When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.
Fits the following BMW engines:
M52, S52, M54
The main reason all of the VANOS units will eventually fail is because the material used for the sealing rings from the factory is not designed for that type of environment. When this happens the only option that BMW leaves you with is buying a new and expensive VANOS unit with the same sealing rings that failed in your original unit.
The VANOS system found in BMW engines is a great feature (when it’s working properly), keeping your power curve smooth and responsive especially in lower to mid RPM range. What usually goes unnoticed is the gradual loss of power within this range as the vehicle's age due to slowly failing seals within the VANOS unit. The way the VANOS system works is based off of oil pressure triggered by a solenoid that allows for a small range of timing degree adjustment, this is where the power curve is affected. When the seals begin to fail (all of them do) there is less pressure to advance the timing reducing the power in that low to mid range. Because this happens slowly it's very hard to notice a difference until you refresh your VANOS unit, then you easily realize the response you've been missing.
There are a number of symptoms that will plague your car as a result of these failing seals such as erratic idle, engine hesitation, stalling, and increased fuel consumption to name a few. If you've been chasing down any of these symptoms with no fix then this could be your issue.
While you're replacing the seals in your VANOS unit it a good time to install anti-rattle spacers to tighten up the gaps in your stock assembly and get rid of that noisy VANOS clatter.
Seals & O-rings:
The seals were the main focus of this project since the OE units are built with Buna-N rubber o-rings instead of the ECS supplied Viton rubber o-rings. The Buna-N material quickly hardens from the heat and chemical exposure within the engine, where the Viton is significantly more resistant to these chemicals. This knowledge was also used when it came to the commonly failed o-rings found on the VANOS seal plate, replaced at the solenoid.
Rattle Repair:
When it comes to the VANOS rattle this is commonly described as "marbles in a can", and can be heard throughout the different RPM ranges depending on the engine. These upgraded rings and washers are precision ground from hardened steel to resist wear and deformation keeping your VANOS rattle free. The rattle repair tools are designed specifically for this VANOS anti-rattle repair, design from hardened steel to stand up to the job. Designed to perfectly follow the splines of the shaft for a tight grip when applying the necessary torque to disassemble & reassemble the VANOS transfer gear. The keyed socket was designed with the intent to use a "common" wrench so this can be completed at home in your garage.
When Servicing your VANOS unit we recommend getting everything you need to replace on the way to service which includes an oil change and valve cover gasket set. Fresh oil and gaskets is the best way to start off a fresh rebuild of any kind giving you the maximum performance of your freshly serviced components.
This item fits the following BMWs:
2000-2001 E46 3 Series M3 M3 Convertible 2000-2006
2001-2002 Z3 Roadster / Coupe Z3 M Roadster Z3 M Coupe w S54 Engine
2006-2008 E86 E86 Z4 Z4 M Roadster Z4 M Coupe
The VANOS system on your N51, N52, and N54 engine controls the valve timing inside the engine. The system is hydraulically operated based on instructions from the engine computer. It's very complex and BMW has not yet perfected the system. The VAN0S solenoid is the actuator that takes instruction from the ECU and activates the VANOS unit on the front of the engine. When the solenoid is failing (or failed) you can end up with a rough running engine, misfires, bad fuel economy, lack of power, and more. It should trigger multiple fault codes and a check engine light for misfires, camshaft control, VAN0S solenoid, boost pressure control, and maybe others. It's important to thoroughly troubleshoot fault codes but VAN0S solenoids are a known issue with these engines.
The VANOS solenoids are located on the front of the engine and may be replaced without removing many other components. In some cases, you may be able to remove the suspect one, clean it, reinstall, and reset your fault codes. If your fault codes come back it's a strong indication that a replacement is required. Or you can buy the new solenoid and replace instead of doing the work twice.
VANOS solenoid for the intake and exhaust are the same part number. Order 2 if you want to replace them both.
When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.
We recommend replacing the solenoid sealing gaskets as well when replacing the solenoid. You can find these under T#363393
This item fits the following BMWs:
2008-2012 E82 BMW 128i 1M Coupe
2008-2010 E82 BMW 135i
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335is - Sedan
2006-2010 E90 BMW 335i 335xi 335i xDrive - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335is - Coupe
2007-2010 E92 BMW 335i 335xi 335i xDrive - Coupe
2007-2013 E93 BMW 328i - Convertible
2007-2010 E93 BMW 335i - Convertible
2006-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive
2011 F10 BMW 528i
2006-2010 E83 BMW X3 3.0i X3 3.0si
2007-2013 E70 BMW X5 3.0si
2006-2008 E85 BMW Z4 3.0i Z4 3.0si
2009-2011 Z4 BMW Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
VAC's S54 Vanos Hub is designed as a direct replacement for the fragile BMW OE Vanos Hub which typically fails due to a broken drive pin. The VAC Hub has an Upgraded Drive Pin design, which is larger in diameter, as well as more material on the outside wall of the pin. In addition, the hub is made from 4340HT Billet Bar and heat treated to the same BMW OE Rockwell Hardness spec. The upgraded design is not only significantly stronger, but the larger diameter Drive Pins also minimize the huge clearance (approximately 1mm) that was in the original design by BMW and reduces the clearance to 0.2mm. This is critical in helping greatly reduce or eliminate the VANOS noise.
Also, this upgraded design eliminates the need for modifying the Pump Ring or having to buy a replacement, which further saves you money!!!
This solenoid works with the VANOS engine timing system to improve horsepower and torque throughout the RPM range.
When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.
Genuine BMW Solenoid Valve (Solv) -
This item fits the following BMW Chassis:
E39,E46,E53 X5,E83 X3,E85
Fits BMW Engines including:
M52,M54,M56
If you're not sure if your Vanos seals are bad then the only question you need to answer is if you've replaced them. Every unit from the factory came with the same failure prone o-rings and seals, even the re-manufactured units you can still get today. The only real fix is by replacing the seals and o-rings with material that is built to last in the oiled, extreme temperature environment found in these kits.
A premium product replacement with easy to follow instructions makes rebuilding your Vanos unit a must. Even thought the power loss is barely felt it's the opposite result once you replace the seals, every car that gets rebuilt ends up wowing the customer and all of them saying they didn't realize what they lost.
There are a number of symptoms that will plague your car as a result of these failing seals such as erratic idle, engine hesitation, stalling, and increased fuel consumption to name a few. If you've been chasing down any of these symptoms with no fix then this could be your issue.
While you 're replacing the seals in your Vanos unit it a good time to install anti-rattle spacers to tighten up the gaps in your stock assembly and get rid of that noisy Vanos clatter.
Rebuild instructions : http://bd8ba3c866c8cbc330ab-7b26c6f3e01bf511d4da3315c66902d6.r6.cf1.rackcdn.com/PDF_12017_BMW_M5X_Dual_Vanos_Rebuild_Kits.pdf
This item fits the following BMWs:
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
1999-2003 E39 BMW 525i 528i 530i
2004-2010 E60 BMW 525i 530i
2004-2006 E83 BMW X3 2.5i X3 3.0i
2000-2006 E53 BMW X5 3.0i
1999-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i
2003-2005 Z4 BMW Z4 2.5i Z4 3.0i
Replace your old, leaking VANOS oil pressure feed line to restore proper function and prevent potential failure.
When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.
Genuine BMW Pressure Hose Assy
This item fits the following BMW Chassis:
E46 M3,E85 Z4M
Fits BMW Engines including:
S54
An important adjustment component for the timing Valvetronic system, this part can cause poor engine performance if it fails. Replace your failed Adjusting Unit with an OEM VDO unit to restore smooth engine operation.
OEM VDO is one of the largest OE providers in the world, supplying numerous vehicle brands, including BMW, with many of their genuine parts that build the vehicle before they ever reach the car lot. Entrusted by many of the top names in automotives and with their proven history of reliability, it makes all of us here at Turner confident that their line of OEM replacement parts are a perfect option to restore your vehicles original operation and performance. The same great quality or higher than Genuine BMW parts at a lower cost.
As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform
BMW S54 3.2L VANOS Elimination Kit - Full Kit | VAC Motorsports is designed to replace the original VANOS unit on the S54 engine, offering a comprehensive solution for performance enthusiasts and racers. Engineered and tested by VAC Motorsports, this kit allows for precise camshaft timing adjustments and is ideal for those using standalone ECUs that do not control the dual-VANOS system.
Kit Includes:
NOTE: ONLY COMPATIBLE WITH AFTERMARKET ECUs
This Valvetronic variable valve timing actuator is designed to optimize engine performance by adjusting the eccentric shaft, effectively increasing or decreasing valve lift and duration as needed. By dynamically controlling valve timing, it enhances power delivery, fuel efficiency, and overall driving performance.
A failing actuator can lead to noticeable power loss, reduced performance, and an illuminated check engine light. Restore your BMW's performance with this premium replacement from Bremmen Parts, designed to meet or exceed OE specifications.
Features:
Exact Fitment: Engineered to perfectly match your BMW’s specifications for seamless installation. Durable Construction: Built with high-strength materials to resist engine heat, vibration, and wear. Precision Manufacturing: Designed to OE dimensions for accurate clearances and alignment. Optimal Performance: Restores proper timing and functionality at all engine speeds. Get your BMW back on the road with reliable performance and confidence.