BMW Tools & Specialty Equipment for BMW 3 Series E93 (2007-2013)

This tool comes in handy especially when working with an engine harness. Certain areas are always prone to corrosion and this tool makes having to re-pin a connector a breeze.

Unlike small screwdrivers, picks, and paper clips, these tools are the correct size and shape to remove and install tiny electrical pins and terminals at plastic block connectors with ease, and will not damage the connectors in the process.

Packaged in a blow molded case to keep everything secure and organized.

Schwaben offers the right tools to make your next project a success. Everything from complex engine scanners to brake bleeders and spring compressors, Schwaben tools has you covered.

Some of the recommended use include but are not limited to:

• Remove and install rear ball joints on E38, E39, E60/61, E63/64, E65/66, and E70's
• Removal and installation of ball joints and bushings on rear control arms on E36, E46, E39, E60/61, E63/64,  E65/66, E70, E83 and E85/86 Z4's
• Removal and installation of rear sub frame mounted differential bushings on E36, E46, E83 and E85/86 Z4's
• Removal and installation of rear differential mounted bushings on E36, E46, E9X, E60/61, E63/64, E65/66, and E85/86 Z4's

When doing work where the mounts and support need to be removed from the engine or transmission having a engine support bar is wise. By using this engine support the stress is coming off of whatever components are still attached reducing future unnecessary repairs. The safety side of it is having the heavy engine and transmission firmly supported as it should be instead of questionable jack techniques.  

Features:

•  2" longer than most
• Deluxe transverse support for even more stability
•  Two angle chain hooks for safer and more stable chain support 
•  61" long and fully adjustable to any width
•  Weight rating is a full 1000 lbs.
•  Includes four rubber padded feet to prevent slipping and damage to cars finish 
• This tool features a dual hook design for holding engine or transmission in place
•  Powder coated for long life and durability

Note: It is important that chains are hooked to both sides of hook, like in photo to insure load is supported evenly. 

Here's what makes this floor jack the best on the market:

• Dual pump pistons to reach maximum height in 5 pumps
• Low profile design keeping lowered cars in mind
• Easy maneuverability 
• Two piece quick release padded handle for storage or transport.

Details:

• Jack Capacity 2 Ton
• Max Lift Height 20"
• Low Height 3.25"
• Chassis Length 26.5"
• Overall Width 13"
• Saddle Diameter 4.5"
• Handle Length 50"
• Shipping Weight 50 lbs

When doing work where the mounts and support need to be removed from the engine or transmission having a engine support bar is wise. By using this engine support the stress is coming off of whatever components are still attached reducing future unnecessary repairs. The safety side of it is having the heavy engine and transmission firmly supported as it should be instead of questionable jack techniques.  

Features:

•  2" longer than most
•  Two angle chain hooks for safer and more stable chain support 
•  61" long and fully adjustable to any width
•  Weight rating is a full 1000 lbs.
•  Includes four rubber padded feet to prevent slipping and damage to cars finish 
• This tool features a dual hook design for holding engine or transmission in place
•  Powder coated for long life and durability

Note: It is important that chains are hooked to both sides of hook, like in photo to insure load is supported evenly. 

This great Schwaben kit is designed to work on todays modern cars. Set contains popular torx and triple square bits found on a lot of German and other European cars. Designed to operate in minimal space situations.

Set Contains:

• 6 stubby triple square with 12 mm hex to be used with included 12 mm ratcheting wrench. 4 mm, 5 mm, 6 mm, 8 mm and 10 mm. 
• 4 stubby triple square with 19 mm hex to be used with included 19 mm ratcheting wrench.. 12 mm regular and  14 mm, 16 mm and 18mm tamper proof triple square.
• Set also includes a 3/8" drive 12 mm socket and 1/2" drive 19 mm socket to fit bits. Good for using bit with ratchet or torque wrench.
• 9 torx bits 10 to 70 torx 
• Includes blow molded case with sturdy foam insert to keep every thing in order.

When it comes to the torque found on axle nuts you're already looking at using a breaker bar or impact gun not to mention the corrosion collected over the years. The safest approach is using impact socket, since they are built with the strength needed to avoid breaking under pressure.

Features:

• Heavy duty ½ inch-drive sockets and drivers have extra thick alloy steel walls, and take a beating that would destroy normal sockets
•  Durable black oxide coating wipes clean easily and resists rust
• Contains three 12-point sockets for a sure grip on the most common sized axle nuts, plus three hex drives for removing common hex-head plugs and fasteners
• Conveniently packaged in a blow molded case, this set will please the most demanding professional technician or discriminating prosumer

Kit includes:

• 30mm, 32mm, and 36mm - 12-point axle nut sockets - ½" drive

• 14mm, 17mm, and 19mm hex head drive axle shoulder bolt sockets - ½" drive