BMW Wheels - Genuine & Performance for BMW 6 Series F06 (2013+)

• 70MM, 80MM, OR 90MM OVERALL LENGTH
• OUR HIGHEST-GRADE PREMIUM WHEEL STUD
• DRY LUBE WITH BLACK M-PHOSPHATE COATING
• STUD FOR RACE/TRACK USE
• CORRECT SHOULDER SIZE FOR A WIDE RANGE OF HUBS/BRAKE ROTORS
• USE WITH 14x1.5 NUT
  
• For the very best in a race-grade wheel stud, stop looking! These are the wheel studs that our race teams insist on (after years of trying every stud design on the market). MSI Racing specializes in hardware for motorsport use (NASCAR and IMSA) and other advanced industries. We tried them on our Grand-Am/IMSA racecars and were very impressed by the performance and durability of their designs. Race wins and championships can come down to the seconds of a pitstop. We could run any wheel stud in the world and we use these. After testing them over the course of a few endurance seasons we decided to offer them to all of our customers as well.
  
  These studs are available in three overall lengths - 70.5mm, 80.5mm, and 90.5mm. All sizes are made with aircraft quality alloy steel and have roll formed threads for greater strength than cut threads. We use a dry film lubricant HM-30 coating containing Teflon & Moly over a manganese phosphate finish. Manganese is preferred over the more common zinc because it's better at reducing friction and wear to prevent thread galling. With the dry lube applied over the phosphate this is the best corrosion resistance we have seen in any wheel stud! Salt tests have shown this stud is superior to others in corrosion resistance. The dry lube helps the nut engage and glide over the threads for faster engagement without cross threading or binding. Other features of our MSI studs include a large bullet nose nut-starter and a properly sized shank to work with a wider range of BMW wheel, nut, and brake rotor combinations. We intentionally avoid the extra large shoulders you see on other studs because they can interfere with some brake rotor hats. The extra large shoulder can be too large to allow the rotor to pass through and drilling out the holes is required (not cool!) Our studs have the sufficient shank for the brake rotor without interfering.
  
  We configured these studs to have a 14x1.25 thread to go into the wheel hub. But the exposed stud has 14x1.5 threads. We did this because threading a nut is faster on 1.5 threads than a finer 1.25 thread pitch, which saved us time during pitstops. There are also more wheel nut options in 14x1.5. When you order our 14x1.25 studs make sure you also order the 14x1.5 nuts.
   

  FREE red threadlocker with purchase of a full set of wheel studs (16 or more)MSI Dry Lube Bullet Nose Wheel Stud Features:
  

• Dry film lubricant HM-30 coating containing Teflon & Moly over a manganese phosphate finish
• Innovative nut-starter and bullet shape radius that all but eliminates cross-threading
• Properly sized shank to work with a wide range of brake rotor, wheel, and nut combinations
• Heat-treated aircraft quality alloy steel
• Developed from over 20 years of top level NASCAR use
  
• These studs are installed using the traditional 'double-nut' method (one regular nut and one jam nut) with thread locking compound (Red Turbo-Lock or similar).
  
  Sold per stud.
  Wheel nuts sold separately.

• 60MM, 75MM, 82MM, OR 90MM OVERALL LENGTH
• EASY INSTALL WITH ALLEN SOCKET
• CERTIFIED ISO/TS 16949 AND ISO 9001 BY TUV
• MANUFACTURED IN EUROPE
• BLACK M-PHOSPHATE COATING
• CORRECT SHOULDER SIZE FOR HUBS/BRAKE ROTORS
• STUD FOR MIXED STREET/TRACK USE

• Wheel studs are among the safest and most beneficial upgrades you can make on a track car. Not only are wheel studs safer than wheel bolts but they make changing wheels/tires much easier. One of the frustrating things about installing your wheels on the hub is that it's difficult to line up the wheel on the bolt holes. As wheels get larger but also heavier it's even more trouble. Add in a wheel spacer and the task is twice as hard. BMW does produce a wheel alignment pin for this purpose but if you're changing wheels often a stud conversion is the better way to go.
  
  Our original bullet nose studs are available in 60mm, 75mm, 82mm, or 90mm. The 75mm works great for cars that do not use a spacer (or a spacer smaller than 10mm). We recommend the 90mm length for cars that have spacers up to 20mm. The 82mm length is a happy medium between the 75mm and the 90mm. These studs come with a OEM-style black zinc coating for excellent corrosion resistance. These studs are perfect for dual-purpose street/track cars. The studs are stronger and safer than wheel bolts with protection against corrosion which makes them suitable for street use. For a dedicated race or track car, where wheel changes or pit stops are more frequent, check out our racing dry lube studs.
  
  Our studs are also designed and manufactured with the properly sized shank to work with a wider range of BMW wheel, nut, and brake rotor combinations. We intentionally avoid the extra large shoulders you see on other studs because they can interfere with some brake rotor hats. The extra large shoulder can be too large to allow the rotor to pass through and drilling out the holes is required (not cool!) Our studs have the sufficient shank for the brake rotor without interfering.
  
  Not all wheel studs are created equal. We don't take a manufacturer's generic wheel stud from their catalog and call it our own. Turner Wheel Studs are manufactured to meet our own specifications. Beware of cheaper studs on the market! We have seen other studs similar to our own designs that are not a true BMW fitment. There are differences that we have ironed out over our years of selling wheel studs for the BMW market. Our stud prices may be slightly higher than the rock bottom prices on the web but we promise that it's a higher quality.
   Turner Bullet Nose Wheel Stud Features:

• Black phosphorous corrosion resistant coating
• Innovative nut-starter and bullet shape radius that all but eliminates cross-threading
• Long shank for good brake rotor alignment
• Heat-treated aircraft quality alloy steel
• Installation Instructions
  Click here for installation instructions and more information.
  
  
  
  Sold per stud.

BFI Center Cap Adapters For BBS E88 Wheels - Brushed - Set of Four are designed to enhance the appearance of BMW's BBS E88 wheels by covering the open center hole with a sleek, brushed finish. These adapters:

• Provide a polished, high-quality look by covering the open center hole
• Are machined from 6061-T5611 aluminum for superior strength and durability
• Feature a hand-brushed finish for a seamless OEM appearance
• Allow the use of 3-prong 70.6mm BBS center caps to add a touch of class
• Are sold in sets of four, with center caps not included

APR Valve Stem Caps - Set Of 4 - Gunmetal offer a stylish and functional upgrade for any vehicle. These high-quality aluminum valve stem caps come in a sleek gunmetal finish and feature an engraved APR logo, which adds a touch of sophistication to your wheels.

• Material: Made from durable aluminum for long-lasting performance
• Design: Engraved APR logo adds a distinctive look
• Finish: Gunmetal color enhances the visual appeal of your wheels
• Set Includes: 4 valve stem caps for a complete upgrade
• Compatibility: Fits most standard valve stems

These APR Valve Stem Caps are designed to provide both aesthetics and durability, making them a great choice for enhancing your vehicle's style.

APR Black Valve Stem Caps are a stylish and functional upgrade for your vehicle's wheels. Sold as a set of four, these high-quality aluminum caps feature an engraved APR logo on each cap. Designed to add a touch of customization to your vehicle, they also serve a practical purpose.

• Premium Quality: Made from durable aluminum for long-lasting performance.
• Enhanced Aesthetics: Features an engraved APR logo for a sleek and stylish look.
• Functional Design: Helps protect valve stems from dirt and moisture.
• Easy Installation: Simple to install and compatible with most standard valve stems.

Upgrade your vehicle with APR Black Valve Stem Caps to enhance both style and functionality.

WHEEL STORAGE RACK:

Now you can stack your extra wheels without the danger of scratches and scuffs. This wheel storage rack keeps your wheels spaced apart, and being on locking casters, allows you to easily move the whole set anywhere in your garage or shop at one time. Sturdy steel construction and a wide base means this wheel rack won't tip over. Holds up to 275 lbs - enough for most any wheel & tire set.

Fits up to 8½" wide wheels, depending on offset

TIRE STACK COVER:

This tire stack by Schwaben is the solution to keeping your tires and wheels clean while in storage.

• Works with 4 tire stacks and works great with our Schwaben Wheel Tree (ES2710754).
• Durable 150D coated material is rated for outdoor use.
• Cover is a large 32" wide X 46" tall.
• Fitted with a long 29" zipper up the side for easy installation and removal.
• Nylon draw string at the bottom allows for a good snug fit.
• Includes a handy storage pouch if not in use.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.