BMW Wheels - Genuine & Performance for BMW 6 Series F12 (2012+)

Vorsteiner Sport Forged wheels are built to provide the ultimate in low weight, strength, and strikingly good looks! These wheels are made using the latest T-6061 aerospace grade aluminum blocks and individually machined to your exacting standards.

The new Vorsteiner V-FS 001 add an another great contender to the lineup of top of the line wheels brought to us by Vorsteiner. They feature a milled split spoke design with a cut-out channel in the middle. In the center are recessed bolt holes and center cap that add another layer of depth to the wheels. Between the split spokes are supports of aluminum that have 3 individual holes cut out, both to save weight and add style to these already aggressive looking wheels.

Vorsteiner have pre-built these wheel kits specifically to fit certain intended vehicles. This kit is for the F10 Non-M 5 Series and features:

• 20x9" ET30 front wheels
• 20x11" ET46 rear wheels
• 72.56mm Center Bore
• 5x120 Bolt Pattern
• Brushed Aluminum Finish

Fits the following BMW's:
2010-2016 F10 BMW Non-M 5 Series

• 70MM, 80MM, OR 90MM OVERALL LENGTH
• OUR HIGHEST-GRADE PREMIUM WHEEL STUD
• DRY LUBE WITH BLACK M-PHOSPHATE COATING
• STUD FOR RACE/TRACK USE
• CORRECT SHOULDER SIZE FOR A WIDE RANGE OF HUBS/BRAKE ROTORS
• USE WITH 14x1.5 NUT
  
• For the very best in a race-grade wheel stud, stop looking! These are the wheel studs that our race teams insist on (after years of trying every stud design on the market). MSI Racing specializes in hardware for motorsport use (NASCAR and IMSA) and other advanced industries. We tried them on our Grand-Am/IMSA racecars and were very impressed by the performance and durability of their designs. Race wins and championships can come down to the seconds of a pitstop. We could run any wheel stud in the world and we use these. After testing them over the course of a few endurance seasons we decided to offer them to all of our customers as well.
  
  These studs are available in three overall lengths - 70.5mm, 80.5mm, and 90.5mm. All sizes are made with aircraft quality alloy steel and have roll formed threads for greater strength than cut threads. We use a dry film lubricant HM-30 coating containing Teflon & Moly over a manganese phosphate finish. Manganese is preferred over the more common zinc because it's better at reducing friction and wear to prevent thread galling. With the dry lube applied over the phosphate this is the best corrosion resistance we have seen in any wheel stud! Salt tests have shown this stud is superior to others in corrosion resistance. The dry lube helps the nut engage and glide over the threads for faster engagement without cross threading or binding. Other features of our MSI studs include a large bullet nose nut-starter and a properly sized shank to work with a wider range of BMW wheel, nut, and brake rotor combinations. We intentionally avoid the extra large shoulders you see on other studs because they can interfere with some brake rotor hats. The extra large shoulder can be too large to allow the rotor to pass through and drilling out the holes is required (not cool!) Our studs have the sufficient shank for the brake rotor without interfering.
  
  We configured these studs to have a 14x1.25 thread to go into the wheel hub. But the exposed stud has 14x1.5 threads. We did this because threading a nut is faster on 1.5 threads than a finer 1.25 thread pitch, which saved us time during pitstops. There are also more wheel nut options in 14x1.5. When you order our 14x1.25 studs make sure you also order the 14x1.5 nuts.
   

  FREE red threadlocker with purchase of a full set of wheel studs (16 or more)MSI Dry Lube Bullet Nose Wheel Stud Features:
  

• Dry film lubricant HM-30 coating containing Teflon & Moly over a manganese phosphate finish
• Innovative nut-starter and bullet shape radius that all but eliminates cross-threading
• Properly sized shank to work with a wide range of brake rotor, wheel, and nut combinations
• Heat-treated aircraft quality alloy steel
• Developed from over 20 years of top level NASCAR use
  
• These studs are installed using the traditional 'double-nut' method (one regular nut and one jam nut) with thread locking compound (Red Turbo-Lock or similar).
  
  Sold per stud.
  Wheel nuts sold separately.

APR Black Valve Stem Caps are a stylish and functional upgrade for your vehicle's wheels. Sold as a set of four, these high-quality aluminum caps feature an engraved APR logo on each cap. Designed to add a touch of customization to your vehicle, they also serve a practical purpose.

• Premium Quality: Made from durable aluminum for long-lasting performance.
• Enhanced Aesthetics: Features an engraved APR logo for a sleek and stylish look.
• Functional Design: Helps protect valve stems from dirt and moisture.
• Easy Installation: Simple to install and compatible with most standard valve stems.

Upgrade your vehicle with APR Black Valve Stem Caps to enhance both style and functionality.