BMW Tools & Specialty Equipment for BMW X Series F16 (2015+)

Plastic five-piece tool kit removes trim and door panels, moldings, and adhesive backed logos and badges, without damage. By using a non-marring plastic you can safely and easily remove trip pieces with confidence

?

Features:

• Pull-type remover

• Narrow edge remover

• Wide edge remover

• Handle remover

• Upholstery clip remover

The Schwaben aluminum wheel hanger makes it easy to remove and install wheels. Just thread the hanger stud into a wheel bolt hole and hang the wheel safely while you rotate tires or remove them for service or vehicle repair. (It's also great for keeping wheel bolt holes aligned on cars with spacers.)

Features:

• Longer & Lighter
• Made of 6061-T6 aluminum
• Anodized for hardness and good looks
• Knurled, non-slip handle has a drilled hole so you can hang it on a pegboard hook in your garage

Protecta socket are used to keep ugly scratch marks from showing up after torqueing down wheel lugs.

Features:

• Coated six-point long reach deep-well impact sockets 
• Color coded mar-free exterior coatings that prevent nicks and scratches left by plain metal sockets
• 17mm, 19mm and 21mm Sockets included

Use these with your breaker bar or impact gun to remove the tightest wheel bolts and lug nuts: when reinstalling wheels, use them to final torque wheel fasteners to factory specifications.

Combine these with our torque limiting sockets and the Schwaben ½-inch torque wrench for a complete wheel fastener solution.

If you're removing trim panels and don't want to scratch or break any pieces then this is a must have. Formed for precision and constructed from plastic to be gentle with the finish.

Features:

•  Wide type remover
• Pull type remover
•  Handy remover
• Narrow type remover
• Upholstery Clip remover
• Angled Clip Panel Remover
• Fork Tip Flat Clip Panel Remover
• Clip Panel Remover
• Sharp Tip Flat Clip Remover
• Panel Remover
• Blunt Tip Flat Clip Panel Remover

Featuring a T60 Torx head, the belt tensioner found on the N54/N55 engine has exceptionally tight quarters. Use of this tool will allow access to the lock pin hole without excessive component removal, making belt removal and installation a much easier task.

This tool fits all N54/N55 powered BMW, including: 
2008+ E82 BMW 135i 1M Coupe 
2014+ F22 BMW M235i 
2006+ E90 BMW 335i 335xi 335i xDrive - Sedan 
2007+ E92 BMW 335i 335is 335xi 335i xDrive - Coupe 
2007+ E93 BMW 335i - Convertible 
2012+ F30 BMW 335i 335i xDrive - Sedan 
2013+ F32 BMW 435i 435i xDrive - Coupe 
2014+ F34 BMW 335i xDrive GT - Gran Tourismo 
2015+ F80 BMW M3 - Sedan 
2015+ F82 BMW M4 - Coupe 
2015+ F83 BMW M4 - Convertible 
2006-2010 E60 BMW 535i 535xi 535i xDrive 
2010+ F07 BMW 535i GT, 535i xDrive GT 
2011+ F10 BMW 535i 535i xDrive 
2012+ F13 BMW 640i 
2009+ F01 BMW 740i 740li 
2011+ F25 BMW X3 xDrive35i 
2007-2013 E70 BMW X5 xDrive35i 
2007-2014 E71 BMW X6 xDrive35i 
2009+ Z4 BMW Z4 sDrive35i Z4 sDrive35is 

The Schwaben Dual Temperature Heat Gun Kit is the ideal tool for stripping paint, removing decals, shrinking wire wrap, etc. The heat gun has a switch which allows for two different heat settings (572F and 932F).

Features:

Four airflow adapters, 1pc Large Deflector Nozzle, 1pc Reduction Nozzle, 1pc Small Deflector Nozzle, and 1pc Reflector Nozzle.
Voltage 120C, 60 HZ
Amps 12.5A
Two heat settings: Low Heat up to 572 Degree F. High Heat 932 Degree F.
Air Volume: Low Heat: 10 cfm (280L/min) High Heat: 17 cfm (480 L/min)
Wattage: Low Heat: 1000W High Heat: 1500W
Has 6.75 Ft cord.
Built in hook to hang on wall.
For California Prop 65 warning see: www.P65Warnings.ca.gov. and photo below.

Wall Hangers Set is the ideal solution for organizing and storing QuickJack frames in a garage. Designed for those who prefer a clean and efficient storage solution, these hangers provide a convenient way to keep your portable car lift frames off the ground and out of the way. The hangers mount directly into a sturdy wall stud, ensuring safe and simple storage for all QuickJack models. Each mount is crafted with a sleek, laser-cut QuickJack logo, affirming its authenticity and quality.

• Secure storage: Mounts directly into wall studs for safe and stable hanging of QuickJack frames.
• Universal fit: Accommodates all QuickJack models, ensuring versatility and convenience.
• Durable construction: Over-engineered to 150% of the rated capacity for long-lasting durability.
• High-quality materials: Made from brushed steel for a robust and stylish appearance.
• Authentic design: Features a sleek, laser-cut QuickJack logo, reflecting its official status and rigorous engineering standards.
• Easy installation: Simple to install, with real-world testing and advanced computer analysis ensuring reliability and resilience.

Upgrade your garage organization with the Wall Hangers Set for a neat, secure, and professional storage solution for your QuickJack frames.