BMW Engine Parts for BMW 2 Series F22 (2014+)

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.

This is the current replacement for some BMW 6 and 8-cylinder engines built in the late 2000s and after. BMW has made numerous changes to ignition coil part numbers in recent years but has approved this part number to work in the vehicles listed below. It's listed as a replacement coil for N20, N55, and S55 engines. In March 2015 BMW approved it for N51/N52 engines. This part number replaces the previous BMW part number 12137594937 for the cars listed below.

Sold per coil. Includes boot and connector.

Revitalize your BMW's performance with Eldor ignition coils. Sluggish acceleration, misfires, and rusty terminals may indicate a worn coil. Located on the engine's top, these coils require inspection and replacement every 60,000 miles or as needed. Ensure your ignition system is in optimal condition for peak performance.

• Revitalize sluggish acceleration
• Address misfires and rusty terminals
• Inspection and replacement every 60,000 miles
• Harmonize ignition system components
• Unlock hidden horsepower
• Improve fuel economy

Upgrade your stock oil cooler thermostat for improved performance. Swap out your existing cover with ease, replacing it with a durable billet cover. Upgrade from your 110-degree Celsius thermostat to a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly unlike thermostat bypass kits.

Kit contents:

Billet thermostat housing cover
Replacement gasket
Hardware
Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

Often an oversight in maintenance, ignition components are also susceptible to wear and tear. Spark Plugs can accumulate carbon, reducing the spark intensity and it's ability to properly ignite the air/fuel mixture, leading to misfires and generally declining performance. Other ignition components, such as coils, boots, wires, caps, and rotors, can also wear out over time due to factors like heat and contamination, preventing the current from reaching the spark plug.

To start over fresh with all new components, we now offer these Ignition Service Kits. Each kit comes with brand new OE quality components, replacing any potential fault points in your ignition system for peak performance!

See kit contents below for a complete list of included components.

Maintaining proper oil levels in your engine is crucial for peak performance. Undetected leaks can cause your oil to drop to dangerously low levels between oil changes, leading to severe engine damage.

One common culprit for oil leaks is the valve cover. Over time, exposure to extreme temperature fluctuations can wear down the gaskets, causing them to fail. Prevent oil leaks and protect your engine by replacing these vital components.

Comprehensive Kit Includes:

Valve Cover Perimeter Gasket Vacuum Pump Seal Valvetronic Actuator Seal HPFP Screws (2) Replace your old gaskets with our high-quality kit to keep your engine running smoothly and efficiently.

BMW uses a lot of plastic in their engine components to save weight and money. Unfortunately, plastic is damaged easily and the factory oil filter cap needs a special tool to remove. This cap is designed to use the original o-ring seal so no special parts are required. You only have to remove the original 'filter cage' from the original cap and transfer it to the new aluminum cap. The satin black anodize blends in with the rest of your engine bay making this a smart and subtle upgrade.

Here is a link to the original Genuine BMW oil filter cap if you are looking for that instead.

Meet modern emission regulations while preserving engine performance with the ECS Baffled Oil Catch Can. Designed for BMW and MINI vehicles, this system efficiently captures blow-by gases, preventing excessive oil vapor ingestion into the intake tract. The innovative 4-chamber baffle system maximizes oil/air separation, reducing carbon build-up and pollutants. Featuring a 1/4" drain fitting for easy maintenance, this catch can minimizes oil deposits, ensuring cleaner emissions and enhanced engine performance.

Key Benefits:

• Efficient 4-chamber baffle system for maximum oil/air separation
• Recirculated design reduces oil ingestion, promoting cleaner emissions
• Durable 6061-T6 billet machined body with anodized black finish for longevity
• Integrated dipstick and sealed reservoir for easy oil inspection and maintenance
• Serviceable design with removable baffle plates for cleaning
• Easy installation with customizable mounting options and leak-free fittings
• Engineered and manufactured in the USA for superior performance and durability

Note: Not for sale or use in the state of California on any pollution-controlled vehicle as per the California Air Resources Board.