BMW Engine Parts for BMW F25 X3 xDrive28i N20 2.0L

Enhance your BMW's performance with the upgraded BAV Ignition Coil, designed to boost firepower and optimize engine efficiency. These coils boast modified core windings for a faster, more efficient burn, resulting in increased torque at lower RPMs and heightened horsepower in the upper range. While improvements depend on your engine's condition, these coils ensure noticeable enhancements in performance and potential fuel economy benefits.

Product Benefits:

Improved engine firepower and efficiency
Increased torque at lower RPMs
Enhanced horsepower in higher ranges
Potential improvement in fuel economy
Set of four for complete BMW Cooper replacement

Stainless steel filtration is not a new technology but is quickly gaining popularity in the automotive segment. With the ability to filter down as small as a paper filter element with the ability to be washed and reused!

The K&P Engineering filter element is made from medical grade, type 304 stainless steel micronic filter cloth to provide unmatched protection against oil contamination and resultant engine damage. A one inch square of this material flows an incredible 1.9 gallons of oil per minute at only 1 PSI pump pressure. The adhesive used in the filter assembly process is good to 600 degrees Fahrenheit, far above normal engine operating temperatures. A super strength nickel-plated neodymium rare earth magnet is installed in the top of the element for magnetic pre-filtering of the oil. The sophisticated bypass is engineered for proper differential pressures and consistent operation, delivering a greater percentage of filtered oil while being very easy to clean. The twist lock design assures positive filter element placement and allows for easy disassembly, inspection, and cleaning. The quad-ring gasket doubles the seal between the filter and the engine. Finally, the filter housing is carved out of solid 6061T6 billet aluminum, which not only looks trick but aids in dissipating heat.

K&P Engineering manufactures stainless steel filters for a vast array of engines around the world. Staying at the forefront of design and testing allows this company to offer a top tier product for your European vehicle.

Features:

• Consistent filtering across entire filter surface
• Superior ASTMF316 filtration performance
• Magnetic Prefiltering
• Progressive rate bypass combined with high flow characteristics of the filter media avoids unfiltered oil bypassing the filter during cold startup and high rpm
• Easy inspection of engine contamination
• Proven in Motorsports, Military and Aerospace applications for years. Technology is FAA approved for use in aircraft. 

At regular oil changes, clean to K&P's specifications for continued used - a true lifetime filter.

This part fits the following BMWs:
2012+ F30 3 Series Sedan 328i 328iX 328i 328iX 335i 335iX 
2006 - 2013 E9X 323i 325i 325xi 328i 328xi 330i 330xi 335i 335xi
2010 - 2016 F10 5 Series Sedan 528i 528iX 530i 535i 535iX 
2003 - 2006 E60 Sedan 525i 525xi 530i 530xi 
2007 - 2010 E60 528i 528xi 535i 535ix 
2009 - 2016 E89 Z4 Roadster Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i 
2014+ F22 2 Series Coupe 228i 228iX M235i M235iX
2007 - 2013 E88 1 Series Convertible 128i 135i
2008 - 2013 E82 1 Series Coupe 128i 135i 135is 1M Coupe
2012 - 2013 E70 X5 xDrive35d X5 xDrive35i
2007 - 2011 E70 X5 3.0sd X5 3.0si 

The Schwaben Piston Ring Filer is a vital tool for obtaining the precise end gap necessary for optimal piston ring performance.

This filer allows you to swiftly and accurately file piston rings to exact measurements, enhancing your engine’s efficiency and lifespan. By simply positioning the piston ring and turning the handle, you can easily rotate the abrasive wheel for a smooth and effective filing process.

**Note:** For the Schwaben Universal Piston Ring Compressor, check out T25805755!

Key Features:

• Optimize Performance: Achieve the perfect end gap crucial for top engine efficiency.
• Quick and Precise: File rings to exact specifications with ease.
• Easy Operation: Position the piston ring and turn the handle to effortlessly rotate the abrasive wheel.
• Enhanced Engine Longevity: Accurate end gaps contribute to longer engine life and better performance.

Instructions:

1. Position the Ring: Place the piston ring on the outer edge against the stop and align the ends squarely against the grinding wheel. Apply light, even pressure against the wheel to prevent grinding too large a gap.
2. Operate the Tool: Turn the handle so the grinding wheel turns towards the inside edge of the ring (counter-clockwise when viewed from the handle side of the tool).
3. Exercise Caution: This is a diamond grinding wheel. It cuts fast!

Checking Piston Ring Gap:

1. Deburr the Ring Ends: Carefully remove any burrs on the ring ends before placing the ring in the bore. A light touch with a fine abrasive stone works well.
2. Clean the Rings: Thoroughly clean the rings with lacquer thinner or acetone, as the paint coating from the factory may occasionally scratch the cylinder bore. Always wear gloves during this process.
3. Position the Ring in the Cylinder: Place the ring squarely in the cylinder bore, about 1" down from the deck surface. An upside-down flat-top piston will help you properly square the ring.
4. Measure the End Gap: Use a feeler gauge to measure the ring's end gap. Apply light grinding pressure and check frequently to avoid making the end gap too large.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Features & Benefits:

Two configurable linear 0-5V analog outputs Ability to calibrate O2 sensors for maximum accuracy Includes LC-2 controller and Bosch wideband O2 sensor Comes with a program cable, manual, and a 10 ft. sensor cable Includes a 1-inch mild steel exhaust bung Innovate MTS serial in/out capability Integrated dual-color status LED (green/red) Patented DirectDigital™ wideband sensor control Positive lock connectors for all connections Real-time display data on screen or with the powerful LogWorks software Range:

AFR (Air-Fuel Ratio) range from 7.4:1 to 22.4:1 (0.5 to 1.5 lambda)

Newest revision of N20/N26 timing chain tensioner from BMW. Replaces part number 11317567680.

Genuine BMW Chain Tensioner -
This item fits the following BMW Chassis:
E89 Z4,F10,F22,F25 X3,F26 X4,F30,F31,F32,F33,F34,F36

Fits BMW Engines including:
N20,N26
 

Introducing Turbosmart’s OPR V2 Turbocharger Oil Pressure Regulator, a cutting-edge solution launched in 2022 that ensures steady oil pressure for your turbocharger. This innovative regulator features a return-less design with an integrated 44 Micron Stainless Steel Mesh Oil Filter, providing robust performance and protection.

The OPR V2 is the first of its kind, utilizing Turbosmart’s proprietary flow control method to maintain optimal oil pressure regardless of engine oil variables like pressure or temperature. It guarantees a smooth oil flow to your turbocharger, safeguarding critical components such as Exhaust Drive, Back & Charge Pressures from excessive oil pressure that could lead to oil consumption and smoke.

Gone are the days of guesswork with restrictors and complex plumbing for oil pressure regulation. The OPR V2 simplifies the process with its return-less, inline installation and the convenience of a built-in 44 Micron Oil Filter. This filter, made of serviceable and replaceable Stainless Steel Mesh, adds an extra layer of defense against engine oil debris that could harm your turbocharger.

Key Features:

Innovative Patent Pending Design Durable Aluminium (6262 T6) Anodised Body & Valve Regulated Oil Pressure Compatible with Most turbochargers Integrated Stainless Steel (304) Mesh Oil Filter -4AN Inlet and Outlet for easy installation 1/8 NPT Sensor/Gauge Port for monitoring Directional Inlet Feed Logic for optimized performance Laminar Flow Output for consistent oil delivery Compatible with all Engine Oils Designed and Manufactured in Australia