Intercooler for BMW 4 Series F32 (2014+)

Engines make more power when you're able to move as much air and fuel as possible through them. However, air density is just as important as air volume. Cooler air is denser air, so in addition to keeping your engine cool, it's important to make sure that your intake charge is as cool as possible. Turner Motorsport's upgraded intercooler works to reduce air temperatures with a bare minimum of pressure drop. Less pressure drop means less restriction, and a turbocharger that doesn't have to work as hard. This results not only in a longer service life for your turbocharger, but a substantial increase in performance as well.

The stepped design increases volume and surface are in a limited space by adding an additional smaller core at the top of the intercooler. Both cross sectional area and frontal surface area are increased by a whopping 56%, with a design that still weighs under 20 pounds. On the stock intercooler, the temperature differential between the inlet and outlet sides of the intercooler represented a 95 degree drop. With the Turner Motorsport intercooler, that drop was increased to a chilling 140 degrees. The dyno results don't lie: as a bolt-in upgrade, expect gains of 18 wheel horsepower and 10 lb/ft of torque. With a tune and supporting modifications, further gains are possible, up to 36 horsepower and 28 lb/ft of torque.

This cast aluminum intercooler features an attractive, easy to clean matte black finish, with etched Turner logos on the front and bottom. If you're looking for the ultimate cooling system upgrade for your turbo BMW, look no further.

• Cast aluminum construction
• Bar and plate design
• 56% increase in frontal surface area & cross sectional area
• Decrease in temperature of 45 degrees from inlet side to outlet side (95 degree drop stock on outlet side vs. 140 degree drop on Turner outlet side)
• Significantly less restriction (pressure drop of consistently 0.75 psi vs. 1.5-2.5 psi stock)
• +18HP/10TQ (+36HP/28TQ with tune and supporting mods)
• Weighs under 20 lbs.
• Overall size: 520mm wide, 210mm tall
• Mounting hardware inlcuded

Upgrade to the following OE Intercoolers: 17517600531, 17517600530, 17517618809

Fits the Following BMWs:

F22 F23 228i 228i M235i M235ix

F30 F31 F32 F33 F34 F36 328i 328ix 335i 335ix 428i 428ix 435i 435ix

Heatsoak is one of the obstacles to making big power from turbocharged engines. The stock intercooler design is commendable for single runs at the stock boost levels, but add any more boost and the system is quickly overwhelmed. As the ECU corrects for heat soak, the boost will be decreased and power reduced. Installing an upgraded intercooler is essential to keeping the engine computer from restraining boost as temperatures climb and helps to maintain boost levels even in the face of elevated turbocharger temperatures. The Evolution Racewerks Competition intercooler is much larger than stock, providing more surface area for cooling air to pass through. Even heat soak at low speeds is reduced, making this a worthwhile addition even for stock or mildly tuned engines.

Available in either Brushed, Polished or Type III Hard Anodized Black, this intercooler looks great and holds up! The hard anodized will not only give your car the stealthy look but will also protect the intercooler fins from damage. Without any reduction in thermal efficiency, hard anodizing will prevent your fins from getting deformed as easily from daily driving or road debris. It also has the added benefit of not drawing attention to the fact that the vehicle has been modified. 

Based out of Nevada, Evolution Racewerks stays at the forefront of performance BMW technology and offers top quality aftermarket parts ahead of the competition. Proven performance gains and an exhausting attention to detail is making ER one of the top names in the industry. Backed by countless successful and happy customers with the timesheets to prove it, Evolution Racewerks is a name you can count on when adding reliable horsepower.

Features:

• Designed specifically to fit (and look good) on the 228i, 328i, and 428i.
• Large 20"x11"x3" (26"x11"x3" with end tanks) High Density Bar & Plate Construction Intercooler Core
• Cast end tanks for improved durability and internal flow characteristics.
• Brush finish standard
• Optional Polished finish available.
• Optional Type III Hard Black Anodizing (for stealth) finish on the intercooler, end tanks, and all piping.  Hard anodizing helps improve the durability of intercooler fins against damage from road debris (rocks).
• Features the factory style connectors.  Fully compatible with factory piping or aftermarket piping utilizing factory style connectors.  Compatible with our charge pipe upgrade kit.
• Maintains ALL factory components.  No modifications required.  100% bolt on.
• Includes all hardware needed to install.
• Developed and tested for over a year under the harsh conditions of racing.
• Limited Lifetime Warranty.

Kit Includes:
1 High-density bar & plate type Competition intercooler
Upgraded charge pipes with silicone couplers
Installation Hardware

This part fits the following BMWs:
2012+ F30 3 Series Sedan 328i 328iX 
2012+ F31 3 Series Touring Wagon 328i 328iX
2014+ F32 4 Series Coupe 428i 428iX 
2014+ F33 4 Series Convertible, 428i 428iX
2014+ F34 Gran Turismo (GT) 328i 328iX 
2015+ F36 4 Series Gran Coupe 428i 428iX 

Heatsoak is one of the obstacles to making big power from turbocharged engines. The stock intercooler design is commendable for single runs at the stock boost levels, but add any more boost and the system is quickly overwhelmed. As the ECU corrects for heat soak, the boost will be decreased and power reduced. Installing an upgraded intercooler is essential to keeping the engine computer from restraining boost as temperatures climb and helps to maintain boost levels even in the face of elevated turbocharger temperatures. The Evolution Racewerks Competition intercooler is much larger than stock, providing more surface area for cooling air to pass through. Even heat soak at low speeds is reduced, making this a worthwhile addition even for stock or mildly tuned engines.

Available in either Brushed, Polished or Type III Hard Anodized Black, this intercooler looks great and holds up! The hard anodized will not only give your car the stealthy look but will also protect the intercooler fins from damage. Without any reduction in thermal efficiency, hard anodizing will prevent your fins from getting deformed as easily from daily driving or road debris. It also has the added benefit of not drawing attention to the fact that the vehicle has been modified. 

Based out of Nevada, Evolution Racewerks stays at the forefront of performance BMW technology and offers top quality aftermarket parts ahead of the competition. Proven performance gains and an exhausting attention to detail is making ER one of the top names in the industry. Backed by countless successful and happy customers with the timesheets to prove it, Evolution Racewerks is a name you can count on when adding reliable horsepower.

Kit Includes:
1 High-density bar & plate type Competition intercooler
Installation Hardware

Features:

• Designed specifically to fit (and look good) on the 228i, 328i, and 428i.
• Large 20"x11"x3" (26"x11"x3" with end tanks) High Density Bar & Plate Construction Intercooler Core
• Cast end tanks for improved durability and internal flow characteristics.
• Brush finish standard
• Optional Polished finish available.
• Optional Type III Hard Black Anodizing (for stealth) finish on the intercooler, end tanks, and all piping.  Hard anodizing helps improve the durability of intercooler fins against damage from road debris (rocks).
• Features the factory style connectors.  Fully compatible with factory piping or aftermarket piping utilizing factory style connectors.  Compatible with our charge pipe upgrade kit.
• Maintains ALL factory components.  No modifications required.  100% bolt on.
• Includes all hardware needed to install.
• Developed and tested for over a year under the harsh conditions of racing.
• Limited Lifetime Warranty.

This part fits the following BMWs:
2014+ F22 2 Series Coupe M235i M235iX
2014+ F23 2 Series Convertible M235i Convertible
2012+ F30 3 Series Sedan 335i 335iX 
2012+ F31 3 Series Touring Wagon 335i 335iX
2014+ F32 4 Series Coupe 435i 435iX 
2014+ F33 4 Series Convertible, 435i 435iX
2014+ F34 Gran Turismo (GT) 335i 335iX 
2015+ F36 4 Series Gran Coupe 435i 435iX 

Heatsoak is one of the obstacles to making big power from turbocharged engines. The stock intercooler design is commendable for single runs at the stock boost levels, but add any more boost and the system is quickly overwhelmed. As the ECU corrects for heat soak, the boost will be decreased and power reduced. Installing an upgraded intercooler is essential to keeping the engine computer from restraining boost as temperatures climb and helps to maintain boost levels even in the face of elevated turbocharger temperatures. The Evolution Racewerks Competition intercooler is much larger than stock, providing more surface area for cooling air to pass through. Even heat soak at low speeds is reduced, making this a worthwhile addition even for stock or mildly tuned engines.

Available in either Brushed, Polished or Type III Hard Anodized Black, this intercooler looks great and holds up! The hard anodized will not only give your car the stealthy look but will also protect the intercooler fins from damage. Without any reduction in thermal efficiency, hard anodizing will prevent your fins from getting deformed as easily from daily driving or road debris. It also has the added benefit of not drawing attention to the fact that the vehicle has been modified. 

Based out of Nevada, Evolution Racewerks stays at the forefront of performance BMW technology and offers top quality aftermarket parts ahead of the competition. Proven performance gains and an exhausting attention to detail is making ER one of the top names in the industry. Backed by countless successful and happy customers with the timesheets to prove it, Evolution Racewerks is a name you can count on when adding reliable horsepower.

Features:

• Designed specifically to fit (and look good) on the 228i, 328i, and 428i.
• Large 20"x11"x3" (26"x11"x3" with end tanks) High Density Bar & Plate Construction Intercooler Core
• Cast end tanks for improved durability and internal flow characteristics.
• Brush finish standard
• Optional Polished finish available.
• Optional Type III Hard Black Anodizing (for stealth) finish on the intercooler, end tanks, and all piping.  Hard anodizing helps improve the durability of intercooler fins against damage from road debris (rocks).
• Features the factory style connectors.  Fully compatible with factory piping or aftermarket piping utilizing factory style connectors.  Compatible with our charge pipe upgrade kit.
• Maintains ALL factory components.  No modifications required.  100% bolt on.
• Includes all hardware needed to install.
• Developed and tested for over a year under the harsh conditions of racing.
• Limited Lifetime Warranty.

Kit Includes:
1 High-density bar & plate type Competition intercooler
Upgraded charge pipes with silicone couplers
Installation Hardware