Showing 269947 results for ""

One of the tricks for getting your BMW to handle better is to add negative camber to the front wheels. This will put more of the tire's width in contact with the ground during cornering. With more rubber there is more grip. BMWs typically have less camber in the front to create understeer. But if you're running a stock setup on the track or autocross you are giving up speed and time as the front tires run out of grip sooner than they should.

Our E90 E92 E93 fixed camber plates are designed from the knowledge we gained from our highly successful racing campaigns with the E46 in the Speed World Challenge series. Our camber plates are offset for the best camber and caster combination for racing purposes when using the stock-diameter sized springs. Camber increases to -2.5° depending on your individual suspension setup, while only increasing ride height by 6mm. The rate of camber change is virtually unaffected throughout the range of suspension travel, reducing the need for other geometry correction. Fixed mount camber plates are legal in many racing and autocross classes - these are the perfect camber solution when adjustable plates are not allowed in your class.

These are very simple to install, requiring only pressing out locator dowels and studs in your factory strut mounts. See below for detailed instructions.

Hub Extenders are the solution that no one else has! BMW wheels must fit on a hubcentric lip to be securely (and safely) mounted to the hub. But with a 3, 5, 8, or some 10mm spacers on a lip measuring no more than 11mm that presented a huge problem - there would be no lip left over for the wheel to rest on! As one of the world's leading BMW tuners and race teams, we came up with a way to extend the lip and get back the lost surface area for the wheel to safely mount on. Our Hub Extenders are the first of their kind.

Hub Extenders fit where the stock dust cap is usually fitted on the front wheel hub. Pop out the dust cap and tap the Hub Extender into its place. It becomes an extension of the original lip. These will only work on the front hubs of the cars listed below because the rear hub is tapered inside (narrows down). These will not work with Xi AWD models because the front axle shaft protrudes through the hub. With Hub Extenders in place you can use nearly any flat wheel spacer - 3mm, 5mm, 7.5mm, 10mm, or possibly more without worrying that the wheel will not be securely seated. This is perfect for wheels that have chamfers on the back of the wheel that don't match up to existing spacers (Kosei K1 spacers for example).

Turner Hub Extender Features --

+ hub extension makes flat spacers a true hubcentric fitment
+ precise tolerance fitment thanks to CAD process and CNC mill machine
+ aerospace grade aluminum  light weight but very strong with a high resistance to corrosion
+ additional military-spec hardcoat for further corrosion resistance
+ stealthy black color with laser engrave Turner logo
+ Turner Motorsport track and street tested!
+ Made in the USA

Wheel Limitations. Special consideration needs to be taken since wheel design and manufacture differ from brand to brand. The key dimension is the dept of the center bore. Some wheels won't work with larger spacers and a Hub Extender because of the additional protrusion into the center bore. Please measure your wheel to make sure it can accommodate an extra 2.5-5mm of hub extending into the center bore. Click here for a diagram.

Hub Limitations. BMW has multiple hub designs but not all are compatible with our Hub Extenders. The inside lip of the hub must be flat and smooth for at least 13mm (the depth our Extender fits into the hub). Some BMW hubs have a bowl shape or have tapered inside walls which will prevent the Hub Extender from seating all the way. Remove the hub dust cap to check before opening your Turner Hub Extenders.

This item fits the following BMWs:
2014+ F22 F23 BMW 228i M235i
1988-1991 E30 BMW M3
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci M3
10/2013+ F30 BMW 320i 328i 335i - Sedan
10/2013+ F31 BMW 328i - Wagon
10/2013+ F34 BMW 328i - Gran Turismo
10/2013+ F32 BMW 428i 435i - Coupe
10/2013+ F33 BMW 428i 435i - Convertible
10/2013+ F36 BMW 428i 435i - Gran Coupe
1982-1988 E28 BMW 524td 528e 533i 535i 535is M5
1989-1995 E34 BMW 525i 530i 535i 540i M5
1982-1989 E24 BMW 633csi 635csi M6
1988-1994 E32 BMW 735i 735il 740i 740il 750il
1995-2001 E38 BMW 740i 740il 750il
1990-1999 E31 BMW 840i 840ci 850i 850ci 850csi
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 Z4 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe

Turner has developed a zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

The rear lower control arms on E82/E9X models are the weakest link in the rear suspension. The arm is made from folded sheetmetal and it bends and deforms easily. Not only will it deform from potholes and curbs, tow truck drivers love to hook onto them without realizing how weak they are. We have seen other race teams complete the box section to make them stronger. A bent arm will throw off the geometry in the suspension, potentially affecting handling and tire wear. These aluminum arms are both lighter and stronger than the factory sheetmetal arms and is the best solution for chronic bending of the stock arm. These are a direct replacement to your stock arms with no changes needed to your alignment. New high-grade hardware is included.

Note: the stock arm is designed from the factory to be intentionally weak. These arms will bend so that something else in the suspension does not break. Our race cars used the stock sheetmetal arm but we replaced them often. We found that it was better to finish a race with a bent arm than not finish due to a catastrophic failure. The ECS arms are still designed to be the weakest link but are far stronger than the factory arm and will not bend as easily.

This item fits the following BMWs:

2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi 335i 335xi M3 - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi 335i 335is 335xi M3 - Coupe
2007-2013 E93 BMW 328i 335i 335is M3 - Convertible

Turner has developed a proprietary zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

Here at Turner we understand the importance of an upgrade that will get the results you need on the track and still be tolerable on the drive around town. When it comes to control arms on the track, making them as stiff as you can (usually using solid mounts) is the best way to increase your driving precision by eliminating the deflection of rubber. The next best thing to create a balance would be to stiffen up the control arm with polyurethane, giving you the option of a more stock like feel with 80a or closer to the solid feel with 95a durometers.

When it comes to the E36 chassis you also get the options of choosing a stock centered design or going with the E30 inspired offset bushing to increase castor, further taking advantage of improvd handling. These poly bushings will give your control arms a direct connection between your suspension and the body of the car eliminating the slop felt under take-off and braking so you feel more in control of your vehicle. 

This item fits the following BMWs that use a centered-style bushing: 

1984-1991 E30 BMW 318i, 318is, 325, 325e, 325es, 325i, 325is 
1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic
1996-1999 E36 BMW M3 S52
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i MZ3 M Coupe M Roadster 

Installs bushings straight and true with minimal effort. Includes tools for both iron and aluminum calipers. Purchase only one tool set for your entire caliper guide bushing upgrade - tools are not one time use.

***Click here for installation instructions*** 

Increase drivetrain rigidity and put that power to the ground! This industry-leading encapsulated design reduces NVH and prevents heat transfer.

From the factory, all BMW models are equipped with soft rubber or fluid-filled engine mounts. While these mounts perform well at isolating drivetrain vibrations, they are prone to degradation and allow for significant drivetrain movement. This often results in a loose-feeling driveline, missed shifts, and a generally disconnected driving feel.

To address these issues, We have developed a performance alternative. Constructed from 6061 Billet Aluminum, these mounts are built to last. While most performance drivetrain mounts feature solid or polyurethane-bonded aluminum construction, the engineers at Turner designed a unique four-piece design that disburses NVH (noise, vibration, and harshness). This multi-piece design offers the added benefit of serviceability. Additionally, encapsulating the polyurethane and adding a TecaPeek isolator prevents heat transfer to the insert, increasing the lifespan and durability of the mount.

Features & Benefits:

High-strength 6061 billet aluminum construction
80A Polyurethane provides a considerable increase over stock rubber durometer, eliminating excess deflection and ensuring drivetrain stiffness.
Instead of the typical polyurethane-bonded aluminum construction, this mount is encapsulated to reduce NVH (noise, vibration, and harshness).
Finished in black hard-coat anodized for a clean, durable, and corrosion-resistant finish.
TecaPeek isolator reduces heat transfer from the engine to the mount insert, increasing the lifespan of the mount.
A simple bolt-on design makes for an easy install
Replace your worn-out factory engine mounts and experience increased drivetrain rigidity, reduced deflection, and more precise shifting. Our Turner Performance Polyurethane Engine Mount Set is designed for maximum durability and strength while maintaining the perfect balance between stiffness and comfort—the perfect choice for your high-horsepower BMW!

The E46 M3 CSL sparked a lot of interest among enthusiasts about the "high kick" look. But what about those who want the aggressive, high kick look without having to replace the entire trunk? We found ourselves scratching our heads, especially unsatisfied with the add-on CSL spoilers you can find on the market.

We took it upon ourselves to CAD design an aggressive, high kick spoiler that pays homage to the CSL trunk, while flowing perfectly with the simple, yet aggressive body lines of the E46 coupe. The carbon fiber is hand laid, with a beautiful gloss finish that will match well with any other carbon fiber accents on your E46 coupe. Our high kick rear spoiler will instantly give your vehicle a more aggressive look.

Includes connector housing with terminals and seals. Commonly used for the camshaft position sensor.

ECS Tuning replacement harness connectors include all necessary pins and wire seals for a complete harness repair. Whether you have a broken harness connector or need a complete wiring repair, we have the components you need.

Each connector includes an additional terminal in case one becomes lost or damaged during installation.

*OEM cross reference PN# 12521433917 - Commonly used for the camshaft position sensor.

Please reference the original part number from the existing connector to confirm fitment, before ordering.

Suggested tools:

Suggested crimping pliers: T#387193
Wire De-pin tools:
12pc De-Pin Tool Set - T#386379
23pc De-Pin Tool Set - T#641943

Turner has developed a proprietary zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

Universal 2.5" inlet to 3.5" outlet exhaust tip. Priced per exhaust tip.

Over the years, it is not uncommon for exhaust tips to be damaged and corroded, becoming a "sore spot" of your BMW. To remedy this unsightly feature, we now offer our very own exhaust tips! Featuring stainless steel construction and a simple, yet sporty design, this exhaust tip will look perfectly at home on almost any model.

Features & Specifications:

Swivel feature for perfect alignment of the exhaust tips in the rear bumper
2.5" Inner Diameter
3.5" Outer Diameter
Mirror Chrome Finish
Double Wall Construction
Angle Cut Style
Includes Stainless Steel Clamp

High Performance air filter, replacement filter for Turner Motorsport intakes, or great for your custom intake project. 

Filter Dimension 

• 152MM length 
• 114MM base
• 60MM inlet 

If allowed in the rules these solid aluminum engine and transmission mounts offer many advantages over a urethane or Delrin mounts. It's no wonder that these mounts have found their way into the top BMW racers in the country. These are machined from solid aluminum and have zero deflection, engine torque will cause a rubber or urethane mount to flex or deflect allowing more torque to passed through the drive line (instead of being wasted winding up the mount). When paired with our flex-free solid transmission mounts you'll get smoother, crisper shifts since the transmission is no longer dancing on the pliable mount. This puts the shift linkages in better consistent alignment. And unlike rubber or urethane the aluminum has zero wear and is not affected by leaking oil or other fluids so this is likely the last set of motor and transmission mounts you will ever need. We very strongly recommend using the solid transmission and engine mounts together as a complete kit, mixing a rubber mount with a metal mount will cause undue stress on the mounting points and will lead to a failure. We never advise using a solid engine mount unless a corresponding solid transmission mount is also used.

These are a no-compromise design for all-out racing use, full solid aluminum mounts should not be used on street-driven cars since there is no material to absorb vibration making these quite harsh for regular street use (track cars don't care about noise).

Product features and benefits:

• Crisper throttle response, positive shifter location, direct power transfer
• Precision machined billet 6061-T6 aluminum housing
• Black anodized for durability and corrosion resistance
• Grade 10.9 stud - fear not, big turbo owners
• Engineered in-house and made in America

This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi 335d 335i 335xi - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi 335i 335is 335xi - Coupe
2007-2013 E93 BMW 328i 335i 335is - Convertible
2009-2016 E89 BMW Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

From the factory, B58-equipped BMWs are designed to be refined and quiet. To achieve this, BMW equipped the intake tract with a bulky plastic resonator designed to cancel out the natural induction sounds of the engine. While great for a silent commute, it robs the enthusiast of the satisfying "whoosh" noise and turbo spool that make the B58 one of the most exciting engines on the market today.

Our Intake Resonator Delete Pipe is the simplest, most cost-effective way to bring that personality back to your BMW without shelling out hundreds for a full intake system. By deleting the OEM intake resonator assembly, you'll experience a drastic increase in induction noise and blow-off sounds. This hose also removes the internal chambers that create turbulence in the factory pipe, ensuring smooth, consistent airflow to the turbocharger. In short, this fully-reversible delete pipe is a must-have upgrade for owners who wish to keep their factory airbox while dramatically increasing induction noise.

Features:

Increases audible induction noise and turbocharger "blow-off" sounds
Removes the internal chambers that cause turbulence in the factory pipe, ensuring smooth, consistent airflow to the turbocharger
Precision-engineered to look like it belonged there from the factory
Perfect for those who want better sound and flow while keeping the superior filtration and heat-shielding of the OE BMW airbox
Design:

Durable four-ply fiber-reinforced silicone construction matches the exact dimensions of the factory air intake elbow (13717643302), ensuring a perfect fit
T304 stainless steel German-style worm gear hose clamps ensure a consistent seal and optimal corrosion resistance
Fully-reversible - no permanent modifications necessary!
Product Development:

Our B58 Intake Resonator Delete Pipe was designed, engineered, tested, and quality inspected by our Research & Development team. Our development process includes leading-edge product technology: FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer, and rigorous long-term product testing.