Camshafts

Schrick Camshaft Set - E90/E92 M3 - 284 Degree

T#:2474

Part#: TMS2474

Ships on Jan 19, 2027

$ 6,478.60 USD

Add to Wish List

Qty

$ 6,478.60 USD

Add to Wish List

This is one full set of Schrick cam shafts, 4 cams total, for the S65 V8 M3 engine. These cams are the 284 degree version, and includes two intake cams and two exhaust cams. Professional installation is a must due to the complexity of the dual VAN0S V8 motor.

Show More Show Less

BMW S52/M52 6 Cyl. 256-Degree - Exhaust Camshaft

T#:637317

Part#: 0261A1561-02

Special Order: No Guaranteed ETA

$ 1,619.99 USD

Add to Wish List

Qty

$ 1,619.99 USD

Add to Wish List

Schrick has been dedicated to engine performance through the development of only the highest-quality camshafts for more than 40 years. They've created a bond with BMW enthusiasts nearly the entire time, offering options for both the street and track using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing. These are the same cams used by many high-end German tuners who are achieving sizeable gains with the M52 and S52 engines. For the power-hungry, these cams are a great way to achieve a linear increase in horsepower from mid-range, up to redline. Duration Exhaust- 256 Duration Exhaust @ 1mm - 227 Exhaust Peak Timing - Cam Lobe Lift Exhaust - Valve Lift w/o Valve Clearance Exhaust - Valve Clearance Exhaust -

Show More Show Less

Schrick Camshaft Set (256/264) - E36 M3, MZ3, M52 inc 2.8 1995-99 ...

T#:3859

Part#: TMS3859

Ships on Dec 18, 2026

$ 2,799.99 USD

Add to Wish List

Qty

$ 2,799.99 USD

Add to Wish List

For the US E36 M3. Schrick 264/256 degree camshafts boost mid-high end power for that extra motivation at higher rpm. Low-end torque is not seriously affected due to the M50/M52s VAN0S System. And, higher profile cams work extremely well with an upgraded intake and exhaust. When upgrading the cams there are other areas you must take into consideration. Higher-flow fuel injectors, larger mass-air sensor, and custom programming are strongly recommended. Turner Motorsport sells complete intake & cam packages that boost power to over 290hp. See the Engine section under Camshafts for more info.

Cam Specs:
Intake - 264 degree, 11.2mm lift
Exhaust - 256 degree, 10.6mm lift

Schrick Technical Information / Specs

This item fits the following BMWs:
1993-1998 E36 BMW 325i 325is 325ic 328i 328is 328ic M3
1993-1995 E34 BMW 525i
1997-1998 Z3 BMW Z3 2.8
1998-1999 Z3 BMW M Roadster M Coupe

Show More Show Less

Schrick Camshaft Set - E90/E92 M3 - 292 Degree

T#:2500

Part#: TMS2500

Ships on Jan 19, 2027

$ 6,478.60 USD

Add to Wish List

Qty

$ 6,478.60 USD

Add to Wish List

This is one full set of Schrick cam shafts, 4 cams total, for the S65 V8 M3 engine. These cams are the 292 degree version, and includes two intake cams and two exhaust cams. Professional installation is a must due to the complexity of the dual VAN0S V8 motor.

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 272 Degree, 12.5m...

T#:338215

Part#: TMS11749

Ships on Dec 18, 2026

Sale - Save 15% $ 2,553.99

This product was last offered at the strikethrough price on
05-03-2026

Starting at $ 2,165.97 USD

Add to Wish List

Sale - Save 15%

$ 2,553.99

This product was last offered at the strikethrough price on
05-03-2026

Starting at $ 2,165.97 USD

Add to Wish List

E46 M3 Schrick 272 Degree Exhaust Camshaft with 12.5mm valve lift. New rocker arms are required (BMW part #11337833259 or a new Schrick part).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick - S54 Exhaust Camshaft (272 Degree, 12.5mm Lift)- E46 M3, Z3M...

T#:11749

Part#: TMS11749

Ships on Dec 18, 2026

$ 824.99 USD

Add to Wish List

Qty

$ 824.99 USD

Add to Wish List

E46 M3 Schrick 272 Degree Exhaust Camshaft with 12.5mm valve lift. New rocker arms are required (BMW part #11337833259 or a new Schrick part).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Camshaft Set - E36 M3-spec - 252/244 Degree

T#:21521

Part#: TMS21521

Ships on Jan 19, 2027

$ 3,470.66 USD

Add to Wish List

Qty

$ 3,470.66 USD

Add to Wish List

These Schrick camshafts are the same specs as the stock US S50 cams -
Intake: 252 degree, 10.2mm lift
Exhaust: 244 degree, 9.5mm lift

With original S50/S52 cams in short supply, and a new set running over $2,000 from BMW, you can source new M3-spec cams from Schrick. These are the same specs as the US S50 engine and very close to the stock S52 cams. These make a great upgrade for M50 (325i, 525i) and M52 engines (328i, 528i) with the proper tuning. These bolt in just like the stock and M3 cams with no special hardware upgrades required - use your stock valve springs, lifters, etc. But for reliability we recommend replacing the lifters, valve springs, and retainers with new stock parts on high mileage engines.

Full cam specs: Schrick Technical Information / Specs

This item fits the following BMWs:
1993-1999 E36 BMW 325i 325is 325ic 328i 328is 328ic M3
1993-1995 E34 BMW 525i
1997-1998 E39 BMW 528i
1997-1998 Z3 BMW Z3 2.8
1998-1999 Z3 BMW M Roadster M Coupe

Show More Show Less

Schrick Camshaft - E30 325i, E34 525 (M20) 304 degree

T#:338233

Part#: 05601040-00

Ships on Jan 18, 2027

Starting at $ 1,489.99 USD

Add to Wish List

Starting at $ 1,489.99 USD

Add to Wish List

Schrick's most aggressive cam for the M20 engine. The 304-degree will make big power at the top but there will be a loss of low-end torque so this cam is only recommended for cars that see most of their time above 4000 rpm. Schrick High Performance valve springs are strongly recommended. This cam has a 12.2mm lift and will not clear stock M20 pistons.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

Show More Show Less

BMW S85 10 Cyl. 296/284-Degree - Camshaft Set

T#:589847

Part#: S85-296-284KT

Ships on Jan 19, 2027

$ 2,113.99 USD

Add to Wish List

Qty

$ 2,113.99 USD

Add to Wish List

This is one full set of Schrick camshafts, 4 cams total, for the S85 V10 M5 engine. These cams are the 296/284 degree version and include two intake cams and two exhaust cams. Professional installation is a must due to the complexity of the dual VAN0S V10 motor.

Show More Show Less

Schrick Camshaft Set - E46 M3, MZ3, MZ4 (S54) - 280/272 12.5mm Lift ...

T#:338745

Part#: E46M3SCHRICK

Ships on Dec 18, 2026

Starting at $ 2,692.99 USD

Add to Wish List

Starting at $ 2,692.99 USD

Add to Wish List

Still looking for more power after bolt-ons? High performance camshafts from Schrick are the way to go. These proved to be an excellent upgrade on our first Project E46 M3 and very similar to the stock E46 M3 CSL cams. Smooth as stock idle with a linear increase in horsepower from midrange all the way to redline. Peak gain was 15hp with no loss in low end torque. The duration of the intake cam is 280 and the exhaust is 272 with 12.5mm valve lift. These are the new "cast" cams from Schrick which require new rocker arms (Schrick or BMW part #11337833859). Professional installation is a must due to the intricacies with the double VAN0S.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 296 Degree, 12.5m...

T#:338218

Part#: 0415A1960-00

Back Ordered

Starting at $ 829.00 USD

Add to Wish List

Starting at $ 829.00 USD

Add to Wish List

E46 M3 Schrick 296 Degree Exhaust Camshaft with 12.5mm lift. This cam is much more aggressive than either of the "standard" Schrick exhaust cams. A new rocker arm is required (Schrick or new BMW part #11337833259).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

BMW S85 10 Cyl. 292/280-Degree - Camshaft Set

T#:1182

Part#: TMS1182

Ships on Jan 19, 2027

$ 5,700.32 USD

Add to Wish List

Qty

$ 5,700.32 USD

Add to Wish List

Schrick has been dedicated to engine performance through the development of only the highest-quality camshafts for more than 40 years. They've created a bond with BMW enthusiasts nearly the entire time, offering options for both the street and track using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing. These are the same cams used by many high-end German tuners who are achieving sizeable gains with the S85 V10 engine. For the power-hungry, these cams are a great way to achieve a linear increase in horsepower from mid-range, up to redline. Duration Intake - 292 Duration Intake @ 1mm - 242 Duration Exhaust - 280 Duration Exhaust @ 1mm - 230 Intake Peak Timing - 145 Exhaust Peak Timing - 130-93 Cam Lobe Lift Intake - 12, 2 Cam Lobe Lift Exhaust - 12, 2 Valve Lift w/o Valve Clearance Intake - 12, 2 Valve Lift w/o Valve Clearance Exhaust - 12, 2 Valve Clearance Intake - Hydraulic Valve Clearance Exhaust - Hydraulic

Show More Show Less

Schrick Camshaft - E30 325i, E34 525 (M20) 284 degree

T#:338235

Part#: 05601840-00

Ships on Jan 18, 2027

Starting at $ 479.00 USD

Add to Wish List

Starting at $ 479.00 USD

Add to Wish List

E30 325i, E34 525 (M20) 284 degree Schrick Camshaft. This is Step 2 in Schrick's line of performance cams. The 284 degree cam will be great for owners who want to retain their driveability on the street and only need a modest boost in top-end RPM. Schrick recommends replacing the valve springs with high-performance springs for this application.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

Show More Show Less

Schrick Camshaft Set - E46 325, 330, 530, X5 3.0, Z3 3.0 - 264/248 ...

T#:4048

Part#: E46-M54-SCHRICK

Ships on Jan 19, 2027

$ 2,915.38 USD

Add to Wish List

Qty

$ 2,915.38 USD

Add to Wish List

Schrick 264 degree (10.5mm lift) intake and 248 degree (10mm lift) exhaust cams provide a power boost at mid-high RPM range without software changes. As used in our 330i ZHP Project Car! These are also available for track / race applications in 272 intake and 256 exhaust durations. We also recommend purchasing Supertech High Performance Valve Springs Call us for details. Professional installation required for all Shrick Camshafts.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

Show More Show Less

Schrick Camshaft - E30 M3 276 degree

T#:203

Part#: TMS203

Special Order: No Guaranteed ETA

$ 1,503.99 USD

Add to Wish List

Qty

$ 1,503.99 USD

Add to Wish List

276-deg Performance Camshaft. This is the next step above the Evo 2/3 cams that we also sell and will produce greater top-end power with only slight loss in torque. This cam can be used on the intake side with a stock exhaust cam OR it can be used on the exhaust side with the 284-deg Schrick cam as the intake.

BMW Schrick Technical Specs

Schrick Technical Information / Specs br>
This item fits the following BMWs:
1988-1991 E30 BMW M3 - S14 engine

Show More Show Less

Schrick Camshaft - E30 E34 M20 284

T#:206

Part#: 05601840-00

Special Order: No Guaranteed ETA

$ 479.00 USD

Add to Wish List

Qty

$ 479.00 USD

Add to Wish List

Schrick has been dedicated to engine performance through the development of only the highest quality camshafts for more than 40 years. They've created a bond with BMW enthusiast nearly the entire time, offering options for both the street and track using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing. This is Step 2 in Schrick's line of performance cams. The 284 degree cam will be great for owners who want to retain their driveability on the street and only need a modest boost in top-end RPM. Schrick recommends replacing the valve springs with high-performance springs for this application.

Show More Show Less

Schrick Camshaft Set - E46 M3, MZ3, MZ4 (S54) - 288/280 12.5mm Lift ...

T#:201497

Part#: TMS201497

Ships on Dec 18, 2026

$ 3,551.99 USD

Add to Wish List

Qty

$ 3,551.99 USD

Add to Wish List

Still looking for more power after bolt-ons? High performance camshafts from Schrick are the way to go. These cams are a direct replacement for the stock cams and give a solid 15+ horsepower boost at the top end and great midrange torque increases too! More gains can be expected with intake and header upgrades and custom software tuning. A slightly lumpy idle is expected at cold start but will be smooth once at operating temperature. This set is just a great all-around cam upgrade for the S54!

These Schrick cams were initially developed for the M3 CSL but they also work great on the US and other non-CSL S54 engines as well. With more duration they are a great match to high flow headers, no cats, or CSL intake manifold upgrades. These are the new "cast" cams from Schrick which require new rocker arms (Schrick recommended or BMW part #11337833259). Professional installation is a must due to the intricacies with the double VAN0S.

Schrick Technical Information / Specs

This item fits the following BMWs:

2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Camshaft - E30 325i, E34 525 (M20) 288 degree

T#:338236

Part#: 05601880-00

Ships on Dec 18, 2026

Starting at $ 490.00 USD

Add to Wish List

Starting at $ 490.00 USD

Add to Wish List

E30 325i, E34 525 (M20) 288 degree Schrick Camshaft. This is Step 3 in Schrick's line of performance cams and the best balance of power and driveability. Expect a big boost of power at the top end but a slight loss in low-end torque. Schrick recommends replacing the valve springs with their own for this application.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

Show More Show Less

Schrick Camshaft - E30 325i, E34 525 (M20) 288 degree

T#:389586

Part#: 338236TCKRM3LJXJ

Ships on Dec 18, 2026

$ 490.00 USD

Add to Wish List

Qty

$ 490.00 USD

Add to Wish List

Schrick Camshaft Set - E30 M3 284/276 degree

T#:3566

Part#: E30M3SCHRICK

Ships on Jan 19, 2027

$ 3,007.27 USD

Add to Wish List

Qty

$ 3,007.27 USD

Add to Wish List

Boost your mid to top end power on your S14 engine with these aggressive Schrick cams! These are the next step above the Evo 2/3 cams that we also sell and will produce greater top-end power with only slight loss in torque. The intake cam is 284 degree (stock is 246) with 11.5mm lift (stock is 10.7) and the exhaust cam is a 276 degree with 11.3mm lift. Motorsport valve springs and adjustable cam sprockets are recommended but not required

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
1988-1991 E30 BMW M3 - S14 engine

Show More Show Less

BMW S50/S52 6 Cyl. 284-Degree - Intake Camshaft

T#:589750

Part#: 0284E1840-0V2

Special Order: No Guaranteed ETA

$ 1,596.99 USD

Add to Wish List

Qty

$ 1,596.99 USD

Add to Wish List

Schrick has been dedicated to engine performance through the development of only the highest-quality camshafts for more than 40 years. They've created a bond with BMW enthusiasts nearly the entire time, offering options for both the street and track using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing. These are the same cams used by many high-end German tuners who are achieving sizeable gains with the S50 and S52 engines. For the power-hungry, these cams are a great way to achieve a linear increase in horsepower from mid-range, up to redline. Duration Intake - 284 Duration Intake @ 1mm - 253 Intake Peak Timing - 129 Cam Lobe Lift Intake - 11, 9 Valve Lift w/o Valve Clearance Intake - 11, 9 Valve Clearance Intake - 0, 25

Show More Show Less

BMW M30 6 Cyl. 284-Degree - Motronik- Camshaft

For Vehicles Equipped With Bosch Monotronik Only

T#:349964

Part#: 002201840-04

Special Order: No Guaranteed ETA

$ 1,191.99 USD

Add to Wish List

Qty

$ 1,191.99 USD

Add to Wish List

Schrick has been dedicated to engine performance through the development of only the highest-quality camshafts for more than 40 years. They've created a bond with BMW enthusiasts nearly the entire time, offering options for both the street and track using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing. These are the same cams used by many high-end German tuners who are achieving sizeable gains with the M30 engine. For the power-hungry, these cams are a great way to achieve a linear increase in horsepower from mid-range, up to redline. Duration Intake - 284 Duration Intake @ 1mm - Duration Exhaust - 280 Duration Exhaust @ 1mm - Intake Peak Timing - 110 Exhaust Peak Timing - 110 Cam Lobe Lift Intake - 8, 7 Cam Lobe Lift Exhaust - 8, 6 Valve Lift w/o Valve Clearance Intake - 10, 9 Valve Lift w/o Valve Clearance Exhaust - 10, 8 Valve Clearance Intake - 0, 25 Valve Clearance Exhaust - 0, 25

Show More Show Less

BMW M10 4 Cyl. 292-Degree - Clockwise Distributor - Camshaft ...

For Vehicles With Clockwise Distributor Only

T#:583620

Part#: 000201920-01

Special Order: No Guaranteed ETA

$ 1,135.99 USD

Add to Wish List

Qty

$ 1,135.99 USD

Add to Wish List

Schrick has been dedicated to engine performance through the development of only the highest-quality camshafts for more than 40 years. They've created a bond with BMW enthusiasts nearly the entire time, offering options for both the street and track using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing. These are the same cams used by many high-end German tuners who are achieving sizeable gains with the M10 engine. For the power-hungry, these cams are a great way to achieve a linear increase in horsepower from mid-range, up to redline. Duration Intake - 292 Duration Intake @ 1mm - 251 Duration Exhaust - 292 Duration Exhaust @ 1mm - 251 Intake Peak Timing - 110 Exhaust Peak Timing - 110 Cam Lobe Lift Intake - 7, 6 Cam Lobe Lift Exhaust - 7, 6 Valve Lift w/o Valve Clearance Intake - 10 Valve Lift w/o Valve Clearance Exhaust - 10 Valve Clearance Intake - 0, 2 Valve Clearance Exhaust - 0,2

Show More Show Less

Schrick Camshaft - E24 633/635, E28 533/535 E34 535i - 284-deg ...

T#:338214

Part#: 002201840-04

Back Ordered

Starting at $ 1,659.87 USD

Add to Wish List

Starting at $ 1,659.87 USD

Add to Wish List

German-made Original Schrick performance camshaft for M30 engines in 1984-up E24 635CSi, E28 533i/535i / 535is, and the E34 535i. This camshaft has a bit more duration and higher lift than the stock cam for improved top-end performance.

Cam Specs

Cam Lift (Valve Lift) I/E (mm)	Duration CRA Intake/Exhaust Peak Timing	Valve Timing CRA IO-IC-EO-EC	Valve lift at TDC I / E (mm)	Valve clearance I / E (mm)	Recommended valve springs
8.7/8.6 (10.9/10.8)	284/280/110	32-72 70-30	1.9 / 1.7	0.25 / 0.25	1982-1984: 000202090 1985-1993: 005602022 (inner) 005602062 (outer)

Schrick Technical Information / Specs

Note: this camshaft is designed to work on the "bolt-on" style distributor rotor. Some cars produced before 1985 with the "slide-on" style rotor require adaptor #11311288027.

Applications:
1984-1989 E24 633CSi, 635CSi
1984-1988 E28 533i 535i, 535is
1989-1993 E34 535i

Show More Show Less

BMW S50/S52 6 Cyl. 284-Degree - Exhaust Camshaft

T#:589751

Part#: 0284A1840-0V2

Special Order: No Guaranteed ETA

$ 1,596.99 USD

Add to Wish List

Qty

$ 1,596.99 USD

Add to Wish List

Schrick has been dedicated to engine performance through the development of only the highest-quality camshafts for more than 40 years. They've created a bond with BMW enthusiasts nearly the entire time, offering options for both the street and track using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing. These are the same cams used by many high-end German tuners who are achieving sizeable gains with the S50 and S52 engines. For the power-hungry, these cams are a great way to achieve a linear increase in horsepower from mid-range, up to redline. Duration Exhaust- 284 Duration Exhaust @ 1mm - 253 Exhaust Peak Timing - 114-76 Cam Lobe Lift Exhaust - 11, 9 Valve Lift w/o Valve Clearance Exhaust - 11, 9 Valve Clearance Exhaust - 0, 25

Show More Show Less

BMW N52 N54 Collar Screw

10X Entries Into Our F80 M3 Sweepstakes

T#:17871157

Part#: 11367524954

In Stock

Sale - Save 20% $ 5.99

This product was last offered at the strikethrough price on
05-03-2026

$ 4.79 USD

Add to Wish List

Qty

Sale - Save 20%

$ 5.99

This product was last offered at the strikethrough price on
05-03-2026

$ 4.79 USD

Add to Wish List

Holds the camshaft gear to the camshaft, measures M10X1X94.

Schrick Intake Camshaft - E46 M3, MZ3, MZ4 (S54) - 288 Degree, 12.5mm...

T#:338222

Part#: TMS3572

Ships on Jan 18, 2027

Sale - Save 28% $ 5,600.99

This product was last offered at the strikethrough price on
07-08-2026

Starting at $ 4,048.04 USD

Add to Wish List

Sale - Save 28%

$ 5,600.99

This product was last offered at the strikethrough price on
07-08-2026

Starting at $ 4,048.04 USD

Add to Wish List

E46 M3 Schrick 288 Degree Intake Camshaft with 12.5mm valve lift. Originally desinged for the M3 CSL but works great in a standard M3. A new rocker arm is required (Schrick or new BMW part #11337833259). This is a more agressive cam that the Schrick 280 degree cam that we also offer for the E46M3

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Cat Cams N54 Sport Camshaft Set

T#:25805744

Part#: 1305001

Special Order: No Guaranteed ETA

$ 1,950.00 USD

Add to Wish List

Qty

$ 1,950.00 USD

Add to Wish List

Upgrade your N54 Engine with Cat Cams, a leader in the performance-aftermarket camshaft industry. These Camshafts will increase airflow into the engine by increasing the overall lift and duration over the factory cams. With their Street cam setup, you can run all factory valvetrain, with no valve spring upgrades necessary! The VANOS (VVT) system on the intake camshaft changes the PD from 125° to 70°. The data are shown for full intake retard (disengaged VVT). The VANOS (VVT) system on the exhaust camshaft changes the PD from 130° to 85°. The data are shown for full exhaust advance (disengaged VVT). Check the distance between valves and piston to be 1mm at least with VVT engaged. Wrong installation will cause severe engine damage! The VANOS (VVT) system on the intake camshaft changes the PD from 125° to 70°. The data are shown for full intake retard (disengaged VVT). The VANOS (VVT) system on the exhaust camshaft changes the PD from 130° to 85°. The data are shown for full exhaust advance (disengaged VVT).

Show More Show Less

Kelford Camshaft Set - Gen 2 B58

T#:25938642

Part#: KEL-B58-GEN2

Ships in 3 Business Days

Starting at $ 2,394.98 USD

Add to Wish List

Starting at $ 2,394.98 USD

Add to Wish List

BMW B58 Gen2 - Stage 1 Street | Strip | Circuit Race | Road Race | Roll Race | Drift | E85 270° / 268° - 10.30mm / 10.15mm Valve Lift 270°/268° cams to suit BMW's Gen 2 B58 engine with bolt-on intake, exhaust, and turbo upgrades. For an engine producing around 550-750hp running a 58-68mm turbo. Still maintains full use of Valvetronic and Double VANOS for good throttle response and wide power band. Must have valve spring upgrade. BMW B58 Gen2 - Stage 2 Strip | Drag Race | Circuit Race | Road Race | Roll Race | Drift | E85 285° / 280° - 10.30mm / 10.60mm Valve Lift 285°/280° stage 2 racing cams for professionally built BMW Gen 2 B58 engine making 750hp-1000hp. Turbo sizing 62-72mm. Great with aftermarket intake plenums. Still can maintain full use of Valvetronic and Dual VANOS. Can run Valvetronic locked in the fully open position when using an aftermarket throttle body. Must have valve spring upgrade. BMW B58 Gen2 - Stage 3 Strip | Drag Race | Roll Race | Drift | E85 | Methanol 288° / 288° - 10.35mm / 10.80mm Valve Lift 288° Stage 3 drag racing cams for professionally built B58 Gen 2 engines making 1200hp+. Turbo sizing 72mm+ on high boost. Fuel-type ethanol blend or methanol. Must use aftermarket high-flow plenum with a throttle body conversion. Recommend locking the Valvetronic system at 100% swing. Must have valve spring upgrade. High Performance Valve Spring Kit - B58 Kelford's performance valve spring and titanium retainer kit is designed to work with the B58B30 straight-6 engine. Made using high-performance PACALOY™, this kit is sure to offer outstanding performance. This kit is specifically engineered to work well with their Stage 1, Stage 2, and Stage 3 camshafts to provide exceptional quality, reliability, and performance. 90lb seat pressure at 36.5 mm installed height; 193lb at 11.0 mm valve lift Spring coil bind height at 23.6 mm

Show More Show Less

Kelford Camshaft Set - Gen 1.5 B58

T#:25938633

Part#: KEL-B58-GEN1.5

Ships in 3 Business Days

Starting at $ 2,394.98 USD

Add to Wish List

Starting at $ 2,394.98 USD

Add to Wish List

BMW B58 Gen1.5 - Stage 1 Street | Strip | Circuit Race | Road Race | Roll Race | Drift | E85 270° / 268° - 10.30mm / 10.15mm Valve Lift 270°/268° cams to suit BMW's Gen 1.5 B58 engine with bolt-on intake, exhaust, and turbo upgrades. For an engine producing around 550-750hp running a 58-68mm turbo. Still maintains full use of Valvetronic and Double VANOS for good throttle response and wide power band. Must have valve spring upgrade. BMW B58 Gen1.5 - Stage 2 Strip | Drag Race | Circuit Race | Road Race | Roll Race | Drift | E85 285° / 280° - 10.30mm / 10.60mm Valve Lift 285°/280° stage 2 racing cams for professionally built BMW Gen 1.5 B58 engine making 750hp-1000hp. Turbo sizing 62-72mm. Great with aftermarket intake plenums. Still can maintain full use of Valvetronic and Dual VANOS. Can run Valvetronic locked in the fully open position when using an aftermarket throttle body. Must have valve spring upgrade. BMW B58 Gen1.5 - Stage 3 Strip | Drag Race | Roll Race | Drift | E85 | Methanol 288° / 288° - 10.35mm / 10.80mm Valve Lift 288° Stage 3 drag racing cams for professionally built B58 Gen 1.5 engines making 1200hp+. Turbo sizing 72mm+ on high boost. Fuel-type ethanol blend or methanol. Must use aftermarket high-flow plenum with a throttle body conversion. Recommend locking the Valvetronic system at 100% swing. Must have valve spring upgrade. High Performance Valve Spring Kit - B58 Kelford's performance valve spring and titanium retainer kit is designed to work with the B58B30 straight-6 engine. Made using high-performance PACALOY™, this kit is sure to offer outstanding performance. This kit is specifically engineered to work well with their Stage 1, Stage 2, and Stage 3 camshafts to provide exceptional quality, reliability, and performance. 90lb seat pressure at 36.5 mm installed height; 193lb at 11.0 mm valve lift Spring coil bind height at 23.6 mm

Show More Show Less

Kelford Camshaft Set - S58

T#:25507146

Part#: KEL-358-S58

Ships in 3 Business Days

Starting at $ 1,399.99 USD

Add to Wish List

Starting at $ 1,399.99 USD

Add to Wish List

Experience a new level of high performance with the upcoming Kelford Cams S58 Camshafts, exclusively at ECS Tuning. Kelford Cams is renowned for its precision-engineered camshafts and valvetrain components, and they're currently in the process of crafting camshafts tailored specifically for the S58 engine, found in BMW G80/G81/G82/G83, X3M, F97 X3M, and F98 X4M models. These camshafts, inspired by the successful design principles of the B58 Camshafts, will focus on rapid spooling and optimizing power throughout the RPM range. BMW S58 | Stage 1 Street | Strip | Circuit Race | Road Race | Roll Race | Drift | E85 288° / 268° - 10.30mm / 10.15mm Valve Lift BMW M Series camshafts are designed for S58 engines with bolt-on intake, exhaust, and turbo upgrades. For engines producing around 600-850hp running a 60-68mm turbo. Maintains full use of Valvetronic and Dual VANOS for great throttle response and wide power band. Must have valve spring upgrade. Kelford recommends their High-Performance Valve Spring Kit BMW S58 | Stage 2 Strip | Drag Race | Circuit Race | Road Race | Roll Race | Drift | E85 292° / 280° - 10.40mm / 10.60mm Valve Lift BMW M Series Racing Camshafts professionally built BMW S58 engines making 800hp-1400hp. Turbo sizing 66-75mm. Great with aftermarket intake plenums. Maintains full use of Valvetronic and Dual VANOS. Can run Valvetronic locked in the fully open position when using an aftermarket throttle body. Must have valve spring upgrade. Kelford recommends their High-Performance Valve Spring Kit Note: Must check intake intermediate rockers for clearance to the new racing cam lobe; OEM pressed steel rockers have sharp edges which may damage the bigger cam lobe. Trim and deburr as necessary. BMW S58 | Stage 3 Strip | Drag Race | Roll Race | Drift | E85 | Methanol 298° / 288° - 10.40mm / 10.80mm Valve Lift BMW M Series Stage 3 drag racing cams designed for professionally built S58 engines producing 1400hp+. Turbo sizing 76mm+ on high boost. Ethanol blend or methanol. Must have valve spring upgrade. Kelford recommends their High-Performance Valve Spring Kit Please Note: Must check intake intermediate rockers for clearance to the new racing cam lobe; OEM-pressed steel rockers have sharp edges which may damage the bigger cam lobe. Trim and deburr as necessary. All engine modifications should be performed by a qualified professional to ensure a proper and safe installation process and a reliable, optimally performing engine.

Show More Show Less

5150 AutoSport & Cat Cams Camshaft Set - 278* / 272* - 11.20mm / 10.3...

T#:39126861

Part#: N55CCCAM-278-272

Ships in 4 Business Days

$ 1,799.99 USD

Add to Wish List

Qty

$ 1,799.99 USD

Add to Wish List

Cat Cams offer great performance at a reasonable price. Cat Cam offers cams in the most popular enthusiast upgrade specs to ensure there is an option for whatever your power goal is. This N55 camshaft set is designed to bring your engine to the next level! Whether it's for street or track purposes, this camshaft set offers the power gains and throttle response needed to push your N55 to its limits. These camshafts are a direct fit for seamless installation and with some simple tuning can produces great power while retaining factory-like idle and driveability. Valvetronic and Dual VANOS functionality can be fully retained, or with an aftermarket throttle body, the valvetronic system can be locked open, providing even more control.

Show More Show Less

Kelford Camshaft Set - Gen 1 B58

T#:25938620

Part#: KEL-CSS-B58-GEN1

Ships in 3 Business Days

Starting at $ 2,394.98 USD

Add to Wish List

Starting at $ 2,394.98 USD

Add to Wish List

BMW B58 Gen1 - Stage 1 Street | Strip | Circuit Race | Road Race | Roll Race | Drift | E85 270° / 268° - 10.30mm / 10.15mm Valve Lift 270°/268° cams to suit BMW's Gen 1 B58 engine with bolt-on intake, exhaust, and turbo upgrades. For an engine producing around 550-750hp running a 58-68mm turbo. Still maintains full use of Valvetronic and Double VANOS for good throttle response and wide power band. Must have valve spring upgrade. BMW B58 Gen1 - Stage 2 Strip | Drag Race | Circuit Race | Road Race | Roll Race | Drift | E85 285° / 280° - 10.30mm / 10.60mm Valve Lift 285°/280° stage 2 racing cams for professionally built BMW Gen 1 B58 engine making 750hp-1000hp. Turbo sizing 62-72mm. Great with aftermarket intake plenums. Still can maintain full use of Valvetronic and Dual VANOS. Can run Valvetronic locked in the fully open position when using an aftermarket throttle body. Must have valve spring upgrade. BMW B58 Gen1 - Stage 3 Strip | Drag Race | Roll Race | Drift | E85 | Methanol 288° / 288° - 10.35mm / 10.80mm Valve Lift 288° Stage 3 drag racing cams for professionally built B58 Gen 1 engines making 1200hp+. Turbo sizing 72mm+ on high boost. Fuel-type ethanol blend or methanol. Must use aftermarket high-flow plenum with a throttle body conversion. Recommend locking the Valvetronic system at 100% swing. Must have valve spring upgrade. High Performance Valve Spring Kit - B58 Kelford's performance valve spring and titanium retainer kit is designed to work with the B58B30 straight-6 engine. Made using high-performance PACALOY™, this kit is sure to offer outstanding performance. This kit is specifically engineered to work well with their Stage 1, Stage 2, and Stage 3 camshafts to provide exceptional quality, reliability, and performance. 90lb seat pressure at 36.5 mm installed height; 193lb at 11.0 mm valve lift Spring coil bind height at 23.6 mm

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 280 Degree, 14.0m...

T#:338217

Part#: TMS201495

Ships on Jan 18, 2027

Starting at $ 3,804.99 USD

Add to Wish List

Starting at $ 3,804.99 USD

Add to Wish List

E46 M3 Schrick 280 Degree Exhaust Camshaft with 14.0mm valve lift. This is only for use in professionally-built E46 M3 race engines. Schrick has developed this ultra-aggressive S54 race cam with 280-deg duration and 14mm of valve lift. Because of the aggressive profile and specs of this cam, Schrick only recommends it be used with special custom pistons with deep valve reliefs. We strongly recommend this be professionally installed by an experienced engine builder to check clearances and fitment.

Schrick also requires valvetrain hardware to go along with this cam:
Schrick valve springs
Schrick rocker arms
Schrick upper and lower retainers

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW Z3 M Roadster, Z3 M Coupe
2006-2008 E85 BMW Z4 M Roadster, Z4 M Coupe

Show More Show Less

Sport Camshaft Single 263/267 - 219/223 - 10.00mm/8.50mm - 0.75mm/1.5...

T#:1980618

Part#: 1302469/S

Special Order: No Guaranteed ETA

$ 413.99 USD

Add to Wish List

Qty

$ 413.99 USD

Add to Wish List

Experience enhanced performance for your Mini with Cat Cams, proudly made in Belgium. Designed to offer superior performance at an affordable price, Cat Cams provides a range of cams in popular enthusiast upgrade specifications. Specifically engineered for W11 Engines with one overhead cam, these billet steel cams are ideal for achieving various power goals. Benefits include:

Enhanced performance for your Mini.
Wide range of enthusiast upgrade specifications available.
Specifically designed for W11 Engines with one overhead cam.
Made from high-quality billet steel for durability and reliability.

Show More Show Less

N14 1.6L Hot Street Camshaft Pair 269/254 - 228/213 - 11.50mm/10.00mm...

T#:26238435

Part#: 1302602

Special Order: No Guaranteed ETA

$ 933.99 USD

Add to Wish List

Qty

$ 933.99 USD

Add to Wish List

Enhance the performance of your Mini's N14 1.6L engine with this pair of Hot Street Camshafts from Cat Cams. Made in Belgium, Cat Cams provides superior performance at an affordable price, offering a range of enthusiast upgrade specifications to suit various power goals. Ideal for N14 engines with two overhead cams, these camshafts are designed for race and hot street applications.

Made in Germany for superior quality
Designed for N14 1.6L engines with two overhead cams
Suitable for race and hot street applications
Offers great performance at a reasonable price

Show More Show Less

W11 R50-R52 Sport Camshaft Single 257/259 - 210/214 - 9.55mm/8.50mm -...

T#:23284070

Part#: 1302461

Special Order: No Guaranteed ETA

$ 413.99 USD

Add to Wish List

Qty

$ 413.99 USD

Add to Wish List

Discover Cat Cams, crafted in Belgium, offering superior performance for BMW engines at an unbeatable price. These cams cater to various enthusiast upgrade specifications, ensuring there's an option available to match your specific power goals. Perfectly designed for W11 Engines featuring one overhead cam.

Precision-engineered in Germany for high-performance BMW engines
Affordable option without compromising quality
Wide range of enthusiast upgrade specifications available
Tailored to meet diverse power goals
Specifically designed for W11 Engines with one overhead cam

Show More Show Less

Sport Camshaft Pair 241/242 - 200/201 - 9.25mm/9.25mm - 0.00mm/0.30mm...

T#:23383341

Part#: 1302601

Special Order: No Guaranteed ETA

$ 933.99 USD

Add to Wish List

Qty

$ 933.99 USD

Add to Wish List

Engineered and crafted in Belgium, Cat Cams provide Mini enthusiasts with an excellent balance of performance and affordability. Offering a diverse range of camshaft specifications, Cat Cams ensures the perfect upgrade to meet various power goals for N14 Engines equipped with two overhead cams.

Key Benefits:

Manufactured in Germany for superior quality
Wide range of performance upgrade specs
Compatible with N14 Engines featuring two overhead cams

Show More Show Less

Cat Cams M52B28 Sport Camshaft Set

T#:25805789

Part#: 1304211

Special Order: No Guaranteed ETA

$ 1,524.99 USD

Add to Wish List

Qty

$ 1,524.99 USD

Add to Wish List

Upgrade your M52B28 Engine with Cat Cams, a leader in the performance-aftermarket camshaft industry. These Camshafts will increase airflow into the engine by increasing the overall lift and duration over the factory cams. With their Sport cam setup, you can run all factory valvetrain, with no valve spring upgrades necessary! The VANOS (VVT) system on the intake camshaft changes the valve timing: M52 /B28: from 115° to 90° (exhaust: 105° fix) The data are shown for full intake retard (disengaged VVT). Check the distance between valves and piston to be 1mm at least with VVT engaged. Wrong installation will cause severe engine damage! Duration Intake @ .1mm: 240° Exhaust @ .1mm: 240° Intake @ 1mm: 203° Exhaust @ 1mm: 203° Lift Intake: 9.25mm Exhaust: 9.25mm Lobe Angle Intake: 110° Exhaust: 105°

Show More Show Less

Cat Cams M52TU B28 Sport Camshaft Set

T#:578586

Part#: 1304405

Special Order: No Guaranteed ETA

$ 1,642.99 USD

Add to Wish List

Qty

$ 1,642.99 USD

Add to Wish List

Made in Belgium, Cat Cams offer great performance at a reasonable price. Cat Cam offers cams in most popular enthusiast upgrade specs to ensure there is a option for what ever your power goal is.

Cat Cams M52TU B28 Turbo Conversion Camshaft Set

T#:25838979

Part#: 1304402

Special Order: No Guaranteed ETA

$ 1,642.99 USD

Add to Wish List

Qty

$ 1,642.99 USD

Add to Wish List

Cat Cams M52B28 Sport Camshaft Set

T#:25805790

Part#: 1304212

Special Order: No Guaranteed ETA

$ 1,524.99 USD

Add to Wish List

Qty

$ 1,524.99 USD

Add to Wish List

Upgrade your M52B28 Engine with Cat Cams, a leader in the performance-aftermarket camshaft industry. These Camshafts will increase airflow into the engine by increasing the overall lift and duration over the factory cams. With their Sport cam setup, you can run all factory valvetrain, with no valve spring upgrades necessary! The VANOS (VVT) system on the intake camshaft changes the valve timing: M52 /B28: from 115° to 90° (exhaust: 105° fix) The data are shown for full intake retard (disengaged VVT). Check the distance between valves and piston to be 1mm at least with VVT engaged. Wrong installation will cause severe engine damage! Duration Intake @ .1mm: 250° Exhaust @ .1mm: 250° Intake @ 1mm: 213° Exhaust @ 1mm: 213° Lift Intake: 9.55mm Exhaust: 9.55mm Lobe Angle Intake: 110° Exhaust: 105°

Show More Show Less

Sport camshaft set 255/248 10.50mm/10.00mm - Z3 1.9 E36 318i ...

T#:578598

Part#: 1301711

Special Order: No Guaranteed ETA

$ 1,170.00 USD

Add to Wish List

Qty

$ 1,170.00 USD

Add to Wish List

Made in Belgium, Cat Cams offer great performance at a reasonable price. Cat Cam offers cams in most popular enthusiast upgrade specs to ensure there is a option for what ever your power goal is.

Schrick Camshaft Set - E46 M3, MZ3, MZ4 (S54) - 288/280 14mm Lift ...

T#:340424

Part#: TMS200186

Back Ordered

Starting at $ 3,261.73 USD

Add to Wish List

Starting at $ 3,261.73 USD

Add to Wish List

E46 M3 Schrick high-performance racing camshaft set - 288 degree intake and 280 degree exhaust. These camshafts are for use in professionally-built E46 M3 race engines. Schrick has developed these ultra-aggressive S54 race cams with 14mm of valve lift. Because of the aggressive profile and specs of this cam, Schrick only recommends them be used with special custom pistons with deep valve reliefs. We strongly recommend these be professionally installed by an experienced engine builder to check clearances and fitment.

Schrick also requires valvetrain hardware to go along with these cams:
Schrick valve springs
Schrick rocker arms
Schrick upper (titanium) and lower (steel) retainers

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW Z3 M Roadster, Z3 M Coupe
2006-2008 E85 BMW Z4 M Roadster, Z4 M Coupe

Show More Show Less

Schrick 05601720-00~SHK M20 2.5L

T#:348282

Part#: 05601720-00

Special Order: No Guaranteed ETA

$ 1,129.99 USD

Add to Wish List

Qty

$ 1,129.99 USD

Add to Wish List

For over 40 years, Schrick has been a pioneer in engine performance, crafting top-quality camshafts trusted by BMW enthusiasts worldwide. Their commitment to excellence is evident in the development of camshafts suitable for both street and track use, constructed from premium materials for unparalleled strength and precision. With a focus on innovation, Schrick has established itself as a leader in engine testing and manufacturing technology. Upgrade your BMW with the 272-degree Schrick Camshaft, offering a significant performance boost over stock cams. Experience enhanced horsepower at higher rpm ranges, where the stock engine may lack vigor. This "street" camshaft maintains low-end torque, ensuring a balanced performance across all speed ranges. For optimal results, Schrick recommends pairing this camshaft with upgraded valve springs.

High-quality camshafts for BMW enthusiasts
Boosts horsepower at higher rpm ranges
Maintains low-end torque for balanced performance
Crafted from premium materials for strength and precision
Recommended for use with upgraded valve springs

Show More Show Less

BMW M20 6 Cyl. 288-Degree - Camshaft

T#:26638223

Part#: 005601880-00

Special Order: No Guaranteed ETA

$ 1,189.99 USD

Add to Wish List

Qty

$ 1,189.99 USD

Add to Wish List

Schrick has been dedicated to engine performance through the development of only the highest-quality camshafts for more than 40 years. They've created a bond with BMW enthusiasts nearly the entire time, offering options for both the street and track using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing. These are the same cams used by many high-end German tuners who are achieving sizeable gains with the M20 engine. For the power-hungry, these cams are a great way to achieve a linear increase in horsepower from mid-range, up to redline. Duration Intake - 288 Duration Intake @ 1mm - Duration Exhaust - 288 Duration Exhaust @ 1mm - Intake Peak Timing - 110 Exhaust Peak Timing - 110 Cam Lobe Lift Intake - 7, 3 Cam Lobe Lift Exhaust - 7, 3 Valve Lift w/o Valve Clearance Intake - 11, 4 Valve Lift w/o Valve Clearance Exhaust - 11, 4 Valve Clearance Intake - 0, 25 Valve Clearance Exhaust - 0, 25

Show More Show Less

Schrick Camshaft - MINI Cooper S

T#:466

Part#: 042401641-03

Special Order: No Guaranteed ETA

$ 1,138.99 USD

Add to Wish List

Qty

$ 1,138.99 USD

Add to Wish List

This 264/272 degree cam for the MINI Cooper S provides a smooth linear power gain from midrange to redline, while idle smoothness is retained. We have seen a 6-8 Horsepower gain from the install of this cam on a stock car - more if the car has been "Sharked" or has have the boost increased.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

Show More Show Less

BMW M30 6 Cyl. 282-Degree - Monotronik- Camshaft

For Vehicles Equipped With Bosch Monotronik Only

T#:26638228

Part#: 002201820-01

Special Order: No Guaranteed ETA

$ 1,567.99 USD

Add to Wish List

Qty

$ 1,567.99 USD

Add to Wish List

Schrick has been dedicated to engine performance through the development of only the highest-quality camshafts for more than 40 years. They've created a bond with BMW enthusiasts nearly the entire time, offering options for both the street and track using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing. These are the same cams used by many high-end German tuners who are achieving sizeable gains with the M30 engine. For the power-hungry, these cams are a great way to achieve a linear increase in horsepower from mid-range, up to redline. Duration Intake - 282 Duration Intake @ 1mm - Duration Exhaust - 282 Duration Exhaust @ 1mm - Intake Peak Timing - 110 Exhaust Peak Timing - 110 Cam Lobe Lift Intake - 8, 4 Cam Lobe Lift Exhaust - 8, 4 Valve Lift w/o Valve Clearance Intake - 10, 6 Valve Lift w/o Valve Clearance Exhaust - 10, 6 Valve Clearance Intake - 0, 25 Valve Clearance Exhaust - 0, 25

Show More Show Less

Schrick Camshaft Set - E46 323/328 M52TU - 248/248

T#:773

Part#: E46M52TUSCHRICK

Ships on Jan 19, 2027

$ 2,915.38 USD

Add to Wish List

Qty

$ 2,915.38 USD

Add to Wish List

M52TU Schrick Camshaft Set. 248 degree 10mm lift intake, 248 degree exhaust. Great for street use. Power gains across the board with calm idle. No need for upgraded valve train. Works perfect for 323 / 328!

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
1999-2000 E46 BMW 323i 323ci 328i 328ci
1999-2000 E39 BMW 528i
1999-2000 Z3 BMW Z3 2.3 Z3 2.8

Show More Show Less

Schrick Camshaft - 2002

T#:338213

Part#: 002.01.920-01

Ships on Jan 18, 2027

Starting at $ 1,135.27 USD

Add to Wish List

Starting at $ 1,135.27 USD

Add to Wish List

Performance cams for M10 engines in the 2002. Schrick makes a variety of cams for the '02 -- from a mild upgrade to highly-aggressive. The specs on the mild 284-deg allow for good mid-range and bottom end and a small increase in the top end. The 292 gives much better punch in the mid range and top end without a loss at the bottom. The 304 makes big power at the top end but sacrifices low end and should only be used with larger carburetors. Schrick High-Performance valve springs are strongly recommended. Schrick makes other cams but they are intended only for serious, professionally-built motors with big carbs.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

Show More Show Less

Project Cars

SELECT YOUR BMW

Sub-Categories

Schrick Technical Information / Specs

Key Benefits:

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results