BMW Internal Engine Parts

ARP Connecting Rod Bolt Set - S54 (M10, 02/2003- Production) ...

T#:2206

Part#: 201-6102

Back Ordered

$ 116.99 USD

Add to Wish List

Qty

$ 116.99 USD

Add to Wish List

Set of 12 ProSeries ARP2000 connecting rod bolts for the Euro-spec M3 engine. Made by ARP, the world leader in fastener technology. The best rod bolts available for the Euro S50 and S54. Ideal for ultra high performance, racing & forced induction applications. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in professional motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods.

This set replaces the factory BMW Euro S50B30 and B32 rod bolts with part number 11-24-1-317-184 (11241317184) and 11-24-1-405-890 (11241405890). It's also used for S54 engines with stock M10 sized rod bolts, which were used from February 2003 production and later. It was also used in earlier engines that had connecting rods replaced. For these 2001-2003 models there is no easy way to check if the rods were replaced, except by checking the rod bolt diameter. If your car has the earlier M11 sized bolt, use ARP kit #201-6103 . Before opening the ARP kit, we recommend that you check your existing rod bolt size as BMW was not consistent with their applications. ARP bolts are not returnable if the package has been open.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1993-1999 E36 BMW Euro M3
2001-2/2003 E46 M3 coupe / convertible*
2/2003-2006 E46 M3 coupe / convertible
2001-2002 MZ3 M Roadster & M Coupe*
2006-2008 MZ4 M Roadster & M Coupe
* - these engines could have either M10 or M11 sized bolts. If the rods and rod bearings were replaced under recall by BMW it should have the newer M10 bolts and this is the correct ARP set to order.

Show More Show Less

ARP Connecting Rod Bolt Kit - M52, M54B30, N20, N26, N54, N55, B46, B...

T#:3315

Part#: 201-6303

Back Ordered

$ 212.99

This product was last offered at the strikethrough price on
04-02-2026

$ 194.99 USD

Add to Wish List

Qty

$ 194.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

This set replaces the 47mm length factory BMW rod bolts with part number 11-24-7-589-671 (11247589671) Check applications before ordering! Opened ARP bolt kits are not
returnable.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following BMWs:
1999-2005 E46 BMW 328i 328ci 330i 330ci 330xi
2001-2003 E39 BMW 530i
2004-2005 E60 BMW 530i
2004-2006 E83 BMW X3 3.0i
2000-2006 E53 BMW X5 3.0i
1997-2002 Z3 BMW Z3 3.0i
2003-2005 Z4 BMW Z4 3.0i

Show More Show Less

ARP Steel Block Head Stud Kit for M50/M52 & S50/S52 (US Spec) ...

T#:3606

Part#: 201-4302

In Stock

19% off MSRP $ 295.92

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 240.99 USD

Add to Wish List

Qty

19% off MSRP

$ 295.92

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 240.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found for the E36 6 cylinder engines, and we highly recommend them in both the racing and forced induction arena. (Due to the additional clamping force between the head and block, these are IDEAL for turbo charging and supercharging!)

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set. Kit includes everything pictured -- 14 head bolts, washers, bolts and assembly lubricant.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These head studs fit the following BMWs/engines (steel block only)
1992-1995 M50 6 cylinder including 325i, 325is and 525i
1996-1999 M52 6 cylinder including 328i, 328is, 323is, 528i
1995-1995 S50US 3.0 liter including 1995 M3 (US only)
1996-1999 S52US 3.2 liter including 1996-1999 M3 (US) and MZ3

Show More Show Less

E46 M3 Schrick DLC-Coated Rocker Arm

T#:342372

Part#: 041513800

In Stock

$ 263.99

This product was last offered at the strikethrough price on
07-07-2026

$ 165.00 USD

Add to Wish List

Qty

$ 165.00 USD

Add to Wish List

The roller rocker arms transfer the rotational force of the camshaft to open the intake and exhaust valves. One end is raised and lowered by the rotating lobe of the camshaft, while the other end acts on the associated valve stem. If a roller rocker arm has failed you may experience a constant ticking noise during engine operation, or alternatively if the rocker arm has broken, you will receive multiple misfires and a rough running engine.

Show More Show Less

ARP Connecting Rod Bolt Kit - E9X M3 S65

T#:2434

Part#: 201-6001

In Stock

$ 533.99

This product was last offered at the strikethrough price on
02-28-2026

$ 460.99 USD

Add to Wish List

Qty

$ 460.99 USD

Add to Wish List

NEW & REVISED!!! ARP has released a new version of their race-grade M3 connecting rod bolts and its better than ever before. If you're replacing your rod bearings these rod bolts are far superior to standard the OE BMW fasteners in terms of durability and ability to withstand stresses. This set of rod bolts is made specifically for the S65 4.0 liter V8, as found in the 2008-2013 M3 and replaces the previous ARP kit part number RBK_S65.

Show More Show Less

ARP Connecting Rod Bolt Kit for E46 M3, MZ3 (M11 Size)

T#:2211

Part#: 201-6103

Back Ordered

$ 215.99 USD

Add to Wish List

Qty

$ 215.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

These bolts are M11 size to replace the stock M11 BMW bolt part number 11-24-7-834-310 (11247834310). The M11 bolt size was used in S54 engines up to 2/2003 production. However, most S54 engines up to that point had their rod bearings replaced under a factory recall and some may have had new connecting rods installed at the same time (or even a new engine altogether). The new bolts installed in these earlier engines are M10 size. Unfortunately, there is no way of knowing which rod or bolt is currently in your car (unless your car came with service records detailing when and what was replaced). The only sure way to know is to check the bolts currently installed in your engine. If yours was updated to the M10 sized bolt, use ARP kit #201-6102 . ARP bolts are not returnable if the pacakge has been open.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
2001-2/2003 E46 M3 coupe / convertible
2001-2002 MZ3 M Roadster & M Coupe

Show More Show Less

ARP Main Stud Kit for M50/M52 and S50/S52 (US)

T#:2208

Part#: 201-5000

In Stock

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

This ARP main stud set for the 24 valves M50-based 6 cylinder engines (including M50, M52, S50US and S52US) and eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each stud is made using the best materials, process, design and engineering, which exceeds even the most stringent racing and aerospace specifications. This main stud kit includes aerospace quality nuts. The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. On the E30 M3, there's no reason to settle for anything less than the best, which is why we carry and use ARP fasteners and studs on our own BMW race cars. ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over. *Does not include washers*

Show More Show Less

Timing Chain Tensioner - E31 E39 E38 E53 E34 E32 Z8

T#:5403287

Part#: 11317531813

In Stock

Sale - Save 19% $ 54.05

This product was last offered at the strikethrough price on
05-03-2026

$ 43.99 USD

Add to Wish List

Qty

Sale - Save 19%

$ 54.05

This product was last offered at the strikethrough price on
05-03-2026

$ 43.99 USD

Add to Wish List

Located in the timing cover and is removable without dis-assembly. This item fits the following BMWs: 1993-1995 E34 BMW 530i 540i 1997-2003 E39 BMW 540i 1988-1994 E32 BMW 740i 740il 1995-2001 E38 BMW 740i 740il 1990-1999 E31 BMW 840i 840ci 2000-2003 E53 BMW X5 4.4i X5 4.6is 2000-2003 E52 BMW Z8 Alpina Roadster

Show More Show Less

ARP S54 Head Stud Kit (E46M3 / MZ3 / MZ4)

T#:3631

Part#: 201-4303

In Stock

$ 247.99 USD

Add to Wish List

Qty

$ 247.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs, particularly on the S54 3.2 liter engine. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best S54 head studs we've found for the E46 M3 6 cylinder engines, and we highly recommend them in both the racing and forced induction arena. (Due to the additional clamping force between the head and block, these are IDEAL for turbo charging and supercharging!)

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set. Kit includes everything pictured -- 14 head bolts, washers, bolts and assembly lubricant.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These head studs fit the following BMWs/engines
2001-2006 E46 M3 coupe & convertible
2001-2002 MZ3 M Roadster & M Coupe (with S54 engine)
2006-2008 MZ4 Z4 M Roadster & M Coupe

Show More Show Less

BMW M20 Engine ARP Head Stud Kit - E30 325i, E34 525i

T#:189783

Part#: 201-4305

In Stock

$ 271.99

This product was last offered at the strikethrough price on
08-13-2026

$ 271.18 USD

Add to Wish List

Qty

$ 271.18 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following BMWs:
1985-1991 E30 BMW 325e 325es 325i 325ic 325is 325ix
1989-1990 E34 BMW 525i

Show More Show Less

Glyco Connecting Rod Bearing Set

T#:375825

Part#: 11241284849

Ships in 1 Business Day

$ 92.02

This product was last offered at the strikethrough price on
07-15-2026

$ 84.36 USD

Add to Wish List

Qty

$ 84.36 USD

Add to Wish List

Standard bore - 45mm

Check Valve - 11367541692

T#:37655979

Part#: 11367541692

In Stock

Sale - Save 11% $ 32.99

This product was last offered at the strikethrough price on
05-03-2026

$ 29.37 USD

Add to Wish List

Qty

Sale - Save 11%

$ 32.99

This product was last offered at the strikethrough price on
05-03-2026

$ 29.37 USD

Add to Wish List

A damaged, leaking, or missing vacuum check valve can lead to engine performance problems, trigger the check engine light, and potentially cause your vehicle to fail an emissions test.

ARP Connecting Rod Bolt Kit - E36 M3 S50/S52 (US only), E46 323/325 ...

T#:2210

Part#: 201-6201

Ships on Sep 3, 2026

$ 222.99

This product was last offered at the strikethrough price on
08-13-2026

$ 194.99 USD

Add to Wish List

Qty

$ 194.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

This set replaces the factory BMW rod bolt number 11-24-1-739-728 (11241739728) which measures 44mm in length. The 44mm BMW rod bolt was used on all US spec E36 M3 (3.0 and 3.2 liter), 1999-2000 E46 323i/323Ci, 2001-2005 325i/325Ci, Z3 1.9,2.5 and 3.2, as well as Z4 2.5. It was also used on SOME of the M50 2.5 liter engines from 1992-1995 -- but check before ordering! Opened ARP bolt kits are not returnable. If your M50 2.5 liter engine has 53mm rod bolts, you will require kit part# 201-6301 instead.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1992-1995 E36 325i/is *** with 44mm rod bolts only ***
1995-1995 E36 M3 S50 3.0 liter (US model)
1996-1999 E36 M3 S52 3.2 liter (US model)
1999-2000 E46 323i & 323Ci (US)
2001-2005 E46 325i, 325xi & 325Ci (US)
1998-2002 Z3 2.3 / 2.5 liter
1998-2000 MZ3 M Roadster & M Coupe
2003-2005 Z4 2.5 liter
*** DOES NOT FIT E36 328 ****

Show More Show Less

Rod Bearing - E30 M3, E28 M5, E24 M6, E34 M5 (sold individually) ...

T#:183

Part#: 11241310515

In Stock

$ 30.59

This product was last offered at the strikethrough price on
05-03-2026

$ 27.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 30.59

This product was last offered at the strikethrough price on
05-03-2026

$ 27.99 USD

Limited Qty Sale

Add to Wish List

E30 M3, E28 M5, E24 M6, E34 M5 Rod Bearing. Sold individually. Standard sizing.

This item fits the following BMWs
1988-1991 BMW E30 M3 - 8 required.
1988 BMW E28 M5 - 12 required.
1989-1993 BMW E34 M5 3.6 liter - 12 required.
1987-1989 BMW E24 M6 - 12 required.

Show More Show Less

Ferrea Performance Intake Valve - Stock Size

T#:583445

Part#: F1550P

Back Ordered

$ 34.99 USD

Add to Wish List

Qty

$ 34.99 USD

Add to Wish List

Timing Chain Tensioner Rail - Right - M62

T#:5470982

Part#: 11311741236

In Stock

Sale - Save 20% $ 49.97

This product was last offered at the strikethrough price on
05-03-2026

$ 39.98 USD

Add to Wish List

Qty

Sale - Save 20%

$ 49.97

This product was last offered at the strikethrough price on
05-03-2026

$ 39.98 USD

Add to Wish List

Timing chain guide rails wear down over time. It is imperative that you replace the chain and rails every 100,000 miles to prevent failure and possible engine damage. Fits the following BMW engines: M62

Show More Show Less

Glyco "Yellow" Crankshaft Bearing Shell - Set - E28, E30, E34, E36, E...

T#:375823

Part#: 11211706847

In Stock

$ 136.06

This product was last offered at the strikethrough price on
07-15-2026

$ 125.04 USD

Add to Wish List

Qty

$ 125.04 USD

Add to Wish List

Standard bore

ARP Main Stud Kit for S54 (E46M3 & Z4M)

T#:2192

Part#: 201-5002

In Stock at Vendor

$ 171.99 USD

Add to Wish List

Qty

$ 171.99 USD

Add to Wish List

This ARP main stud set is for the S54 3.2 liter, as found in all 2001 to 2006 E46 M3, as well as the 2006-2008 Z4 M Roadster and M Coupe models. Switching to the ARP main stud kit eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each stud is made using the best materials, process, design and engineering, which exceeds even the most stringent racing and aerospace specifications. This S54 main stud kit includes hardened parallel-ground washers and aerospace quality nuts.

The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. On the E30 M3, there's no reason to settle for anything less than the best, which is why we carry and use ARP fasteners and studs on our own BMW race cars.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This ARP main stud kit fits the following BMWs:
2001-2006 E46 M3 3.2 liter coupe/convertible
2001-2002 MZ3 M Coupe & M Roadster (S54 engine)
2006-2008 MZ4 M Coupe & M Roadster

Show More Show Less

ARP Connecting Rod Bolt Kit for E36 325 with 53mm Rod Bolt

T#:2186

Part#: 201-6301

In Stock at Vendor

20% off MSRP $ 243.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 194.99 USD

Add to Wish List

Qty

20% off MSRP

$ 243.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 194.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

This set replaces the 53mm length factory BMW rod bolts with part number 11-24-1-713-342 (11241713342) which was used on SOME of the M50 2.5 liter engines from 1992-1995. Check before ordering! Opened ARP bolt kits are not returnable. If your M50 2.5 liter engine has 44mm rod bolts, you will require kit part# 201-6201 instead.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1992-1995 E36 325i/is *** with 53mm rod bolts only ***

Show More Show Less

ARP Head Stud Kit - N54

T#:24112781

Part#: ARP-HSK-N54-S

Back Ordered

$ 499.99 USD

Add to Wish List

Qty

$ 499.99 USD

Add to Wish List

Oil Pressure Control Valve - 11417639993

T#:37655968

Part#: 11417639993

In Stock

$ 109.99 USD

Add to Wish List

Qty

$ 109.99 USD

Add to Wish List

Unlike traditional BMW engines, modern engines, like the B48 and B58, use a volume-flow-regulated oil pump. Instead of providing a consistent volume of oil, these new systems control oil supply at each individual operating range.

This Control Valve Solenoid is a critical component in the volume-flow-regulated oiling system. This piece seamlessly adjusts the oil pressure based on inputs from the DME. In the event of failure, this means the engine oil supply system may become restricted.

Thankfully, Bremmen Parts offers this high-quality, OE replacement Control Valve Solenoid at a fraction of Genuine price. Built with durability and fitment in mind, this component is an exact fit for your BMW.

Show More Show Less

Ferrea Performance Exhaust Valve - Stock Size

T#:583444

Part#: F1552P

Ships on Sep 1, 2026

$ 34.99 USD

Add to Wish List

Qty

$ 34.99 USD

Add to Wish List

BMW S14 Engine ARP Head Stud Kit - E30 M3

T#:189786

Part#: 201-4605

In Stock at Vendor

$ 160.99 USD

Add to Wish List

Qty

$ 160.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following BMWs:
1987-1991 E30 BMW M3

Show More Show Less

N52 Valvetronic Camshaft Adjusting Unit - 11377548388

T#:36066208

Part#: 11377548388

In Stock

Sale - Save 20% $ 148.99

This product was last offered at the strikethrough price on
05-03-2026

$ 119.13 USD

Add to Wish List

Qty

Sale - Save 20%

$ 148.99

This product was last offered at the strikethrough price on
05-03-2026

$ 119.13 USD

Add to Wish List

This Valvetronic variable valve timing actuator is designed to optimize engine performance by adjusting the eccentric shaft, effectively increasing or decreasing valve lift and duration as needed. By dynamically controlling valve timing, it enhances power delivery, fuel efficiency, and overall driving performance.

A failing actuator can lead to noticeable power loss, reduced performance, and an illuminated check engine light. Restore your BMW's performance with this premium replacement from Bremmen Parts, designed to meet or exceed OE specifications.

Features:

Exact Fitment: Engineered to perfectly match your BMW’s specifications for seamless installation. Durable Construction: Built with high-strength materials to resist engine heat, vibration, and wear. Precision Manufacturing: Designed to OE dimensions for accurate clearances and alignment. Optimal Performance: Restores proper timing and functionality at all engine speeds. Get your BMW back on the road with reliable performance and confidence.

Show More Show Less

Bremmen Parts Eccentric Shaft - BMW N55 S55 3.0L

T#:36913364

Part#: 11377589883

Ships on Sep 28, 2026

Sale - Save 20% $ 614.99

This product was last offered at the strikethrough price on
05-03-2026

$ 491.22 USD

Add to Wish List

Qty

Sale - Save 20%

$ 614.99

This product was last offered at the strikethrough price on
05-03-2026

$ 491.22 USD

Add to Wish List

This eccentric shaft is a vital component of your BMW's N55 Valvetronic system, responsible for precise control of valve lift. In the N55 engine, the Valvetronic system uses intermediate levers between the camshaft and lifters to adjust valve lift dynamically. These levers are actuated by this eccentric shaft, which is rotated by an electronically controlled motor under the direction of the engine computer.

Eccentric shaft failure is a common issue in N55 engines, often caused by inadequate lubrication due to extended oil change intervals. The most frequent failure occurs when the eccentric shaft gear wears down, leading to disengagement from the motor's worm drive. Symptoms include multiple fault codes, such as P1014 (Shaft Parity Error), P1017 (Shaft Sensor Plausibility), P1023 (Valvetronic Adjustment Range), and P10E1 (Valvetronic System No Travel Detected).

If your BMW is experiencing Valvetronic-related fault codes, a failing eccentric shaft could be the source of the problem. Opt for this premium direct replacement from Bremmen Parts to restore your Valvetronic system's functionality and ensure a durable, high-quality repair.

Show More Show Less

Bremmen Camshaft Position Sensor - E46 E39 E60 E83 Z3 Z4

T#:640145

Part#: 12147518628

In Stock

Sale - Save 16% $ 31.99

This product was last offered at the strikethrough price on
05-03-2026

$ 26.87 USD

Add to Wish List

Qty

Sale - Save 16%

$ 31.99

This product was last offered at the strikethrough price on
05-03-2026

$ 26.87 USD

Add to Wish List

A bad cam sensor can cause a variety of problems from hard starting to stalling at low speeds. Cam sensor replacement has been known to cure many drivability issues

Crankcase Ventilation Hose

T#:35357255

Part#: 11157848341

In Stock

Sale - Save 21% $ 54.99

This product was last offered at the strikethrough price on
05-03-2026

$ 43.24 USD

Add to Wish List

Qty

Sale - Save 21%

$ 54.99

This product was last offered at the strikethrough price on
05-03-2026

$ 43.24 USD

Add to Wish List

Crank Timing Sprocket - M42 M44

T#:5471083

Part#: 11211247338

In Stock

Sale - Save 20% $ 65.27

This product was last offered at the strikethrough price on
05-03-2026

$ 52.22 USD

Add to Wish List

Qty

Sale - Save 20%

$ 65.27

This product was last offered at the strikethrough price on
05-03-2026

$ 52.22 USD

Add to Wish List

Crankshaft located timing gear used in the operation of the timing chain. This item fits the following BMW Chassis: E30,E36 Fits BMW Engines including: M42,M44

ARP Main Stud Kit for E30 M3 S14 Engine

T#:2207

Part#: 201-5001

In Stock

$ 119.99 USD

Add to Wish List

Qty

$ 119.99 USD

Add to Wish List

This ARP main stud set for the E30 M3 eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each S14 main stud is made using the best materials, process, design and engineering, which exceeds even the most stringent racing and aerospace specifications. This main stud kit includes hardened parallel-ground washers and aerospace quality nuts.

The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. On the E30 M3, there's no reason to settle for anything less than the best, which is why we carry and use ARP fasteners and studs on our own BMW race cars.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This ARP main stud kit fits the following BMWs:
1988-1991 E30 M3 - S14 engine
1984-1985 E30 318i (M10)

Show More Show Less

ARP Connecting Rod Bolt Kit for E30 M3 2.3 liter

T#:2187

Part#: 201-6104

In Stock at Vendor

$ 175.99 USD

Add to Wish List

Qty

$ 175.99 USD

Add to Wish List

Set of 8 Pro-Series connecting rod bolts, made by ARP -- the world leader in fastener technology. ARP Pro Series connecting rod bolts are precision CNC-machined to exacting specifications and designed for optimum reliability. Heat-treated with threads which are rolled to provide up to ten times more fatigue strength, these rod bolts are far superior to standard OEM BMW fasteners in terms of durability and ability to withstand stresses. This rod bolt set is specifically for the E30 M3 S14 2.3 liter engine.

Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1988-1991 E30 M3 - S14 4 cylinder

Show More Show Less

ARP Cylinder Head Stud Kit - M30 BMW 3.0L 3.4L

T#:379415

Part#: 201-4602

In Stock at Vendor

$ 255.99 USD

Add to Wish List

Qty

$ 255.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated, ensuring complete heat penetration, to increase the clamping load up to 200,000 psi. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set.

This item fits the following BMW Engines:
M30 3.0L 3.4L I6

Show More Show Less

ARP Cylinder Head Stud Kit - E9X M3 S65

T#:554124

Part#: 201-4307

Ships in 7 Business Days

$ 363.99 USD

Add to Wish List

Qty

$ 363.99 USD

Add to Wish List

ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated, ensuring complete heat penetration, to increase the clamping load up to 200,000 psi. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Show More Show Less

ARP Rod Bolt Kit - S85

T#:1637703

Part#: 201-6002

Ships on Sep 9, 2026

$ 569.99 USD

Add to Wish List

Qty

$ 569.99 USD

Add to Wish List

VANOS Solenoid Actuator - 11367593719

T#:37655980

Part#: 11367593719

In Stock

Sale - Save 16% $ 37.99

This product was last offered at the strikethrough price on
05-03-2026

$ 32.07 USD

Add to Wish List

Qty

Sale - Save 16%

$ 37.99

This product was last offered at the strikethrough price on
05-03-2026

$ 32.07 USD

Add to Wish List

This Solenoid Actuator is responsible for adjusting camshaft timing through precise phasing, ensuring optimal engine performance.

As a common culprit behind VANOS-related trouble codes, replacing this component can be expensive. Opt for a durable and cost-effective solution with a high-quality replacement from Bremmen Parts, designed to deliver reliable performance without breaking the bank.

Show More Show Less

ARP ARP2000 Head Stud Kit - N55

T#:42335661

Part#: ARP-HSK-N55-S

In Stock

$ 699.99 USD

Add to Wish List

Qty

$ 699.99 USD

Add to Wish List

Enhance your BMW N55 engine's ability to handle higher levels of boost with 5150's custom-designed Head Stud Kit from ARP, the global leader in fastener technology!

Main Bearing Set - Standard Size - E30 M3 2.3 liter

T#:3166

Part#: 11210666110

Ships in 3 Business Days

$ 99.99 USD

Add to Wish List

Qty

$ 99.99 USD

Add to Wish List

This E30 M3 Main bearing set is in standard size for the 2.3 liter S14 engine. This main bearing kit includes the thrust bearings.

This item fits the following BMWs:
1988-1991 E30 BMW M3

Show More Show Less

MINI R55 to R61 Crankshaft Gear

T#:583703

Part#: 11217588996

In Stock

Sale - Save 18% $ 25.99

This product was last offered at the strikethrough price on
05-03-2026

$ 21.24 USD

Add to Wish List

Qty

Sale - Save 18%

$ 25.99

This product was last offered at the strikethrough price on
05-03-2026

$ 21.24 USD

Add to Wish List

The lower sprocket gear, situated at the engine's bottom, mounts to the crankshaft and is commonly replaced during timing chain modifications for Mini engines. This critical component ensures proper timing and synchronization within the engine system, contributing to efficient and smooth engine performance.

Essential for timing chain modifications
Mounts to the crankshaft at the engine's base
Ensures proper engine timing and synchronization
Contributes to efficient engine performance

Show More Show Less

ARP Cylinder Head Stud Kit - ARP2000 - BMW B58 3.0L

T#:1105898

Part#: 201-4701

In Stock

20% off MSRP $ 459.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 367.99 USD

Add to Wish List

Qty

20% off MSRP

$ 459.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 367.99 USD

Add to Wish List

For engine builders crafting a high-performance powerhouse, the ARP Cylinder Head Stud Kit is the industry-standard choice for reliability and strength. Each kit features studs, nuts, and washers manufactured from ARP’s proprietary ARP2000 alloy, a material rated far superior to standard aircraft-quality steels.

Show More Show Less

ARP Main Stud Kit for BMW/MINI 1.6 N12/N14/N16/N18 Engine

T#:189787

Part#: 201-5401

In Stock at Vendor

$ 251.99 USD

Add to Wish List

Qty

$ 251.99 USD

Add to Wish List

This ARP main stud set for the new MINI F engines eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each main stud is made using the best materials, process, design and engineering, which exceeds even the most stringent racing and aerospace specifications. This main stud kit includes hardened parallel-ground washers and aerospace quality nuts.

The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. On the MINI, there's no reason to settle for anything less than the best, which is why we carry and use ARP fasteners and studs on our own BMW race cars.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

Show More Show Less

Timing Chain Guide Rail - Left

T#:5471008

Part#: 11311704945

In Stock

Sale - Save 20% $ 52.01

This product was last offered at the strikethrough price on
05-03-2026

$ 41.61 USD

Add to Wish List

Qty

Sale - Save 20%

$ 52.01

This product was last offered at the strikethrough price on
05-03-2026

$ 41.61 USD

Add to Wish List

Lower portion for bank 2 (5-8) This item fits the following BMWs: 1997-1998 E39 BMW 540i 1996-1998 E38 BMW 740i 740ill 1996-1999 E31 BMW 840i 840ci

Schrick Intake Camshaft - E46 M3, MZ3, MZ4 (S54) - 288 Degree, 12.5mm...

T#:3572

Part#: TMS3572

Ships on Dec 3, 2026

$ 1,775.98 USD

Add to Wish List

Qty

$ 1,775.98 USD

Add to Wish List

E46 M3 Schrick 288 Degree Intake Camshaft with 12.5mm valve lift. Originally desinged for the M3 CSL but works great in a standard M3. A new rocker arm is required (Schrick or new BMW part #11337833259). This is a more agressive cam that the Schrick 280 degree cam that we also offer for the E46M3

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 272 Degree, 12.5m...

T#:11749

Part#: TMS11749

Ships on Dec 3, 2026

$ 824.99 USD

Add to Wish List

Qty

$ 824.99 USD

Add to Wish List

E46 M3 Schrick 272 Degree Exhaust Camshaft with 12.5mm valve lift. New rocker arms are required (BMW part #11337833259 or a new Schrick part).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Intake Camshaft - E46 M3, MZ3, MZ4 (S54) - 280 Degree, 12.5mm...

T#:11748

Part#: TMS11748

Ships on Dec 3, 2026

$ 1,867.99 USD

Add to Wish List

Qty

$ 1,867.99 USD

Add to Wish List

E46 M3 with S54 engine Schrick 280 Degree Intake Camshaft with 12.5mm valve lift. A new rocker arm is required (Schrick or new BMW part #11337833259).

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Camshaft - M20 288 degree

T#:3501

Part#: 05601880-00

Ships on Dec 3, 2026

$ 490.00 USD

Add to Wish List

Qty

$ 490.00 USD

Add to Wish List

SEE T#338236

Main Stud Kit - M50/M52/S50/S52

T#:26171653

Part#: ARP-MSK-M50

Back Ordered

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

This ARP Main Stud Kit is designed to replace BMW 11111735525 for the M50/M52/S50/S52 engines that were used in a variety of BMW models. One significant advantage of these main studs is their ability to prevent main cap walk, which can occur when the main caps shift or move out of position, potentially causing damage to the engine. In addition, ARP Main Studs can safeguard the threads of your engine block, providing an extra layer of protection against potential damage. When opting for main studs instead of factory bolts, it's important to note that the engine builder should mic the bores. Using studs may require a line hone to ensure proper fitment and alignment. A line hone is a machining process that can be used to resize and reshape the main bearing bores, ensuring that they are perfectly round and concentric. This is crucial for ensuring proper oil clearance and preventing premature bearing wear. By mic'ing the bores and performing a line hone if necessary, engine builders can ensure that the main studs are installed correctly and that the engine will perform reliably and at its best. Installation Instructions: To ensure accurate torque readings and proper thread engagement, thoroughly clean all threads in the engine block. If necessary, use an ARP chaser to chase the threads. Before installing any hardware, carefully inspect and clean it for defects, shipping damage, and proper fit, length, and dimension. Gently screw the main studs into the engine block by hand until they are snug. Install the main caps, checking for any binding or misalignment. Apply ARP Ultra-torque fastener assembly lubricant to the threads of the studs, nuts, and washers. Install the washers and nuts onto the studs and tighten them by hand. It is highly recommended to use the ARP Ultra-torque fastener assembly lubricant provided with the kit, as it provides consistent clamping force and reduces friction on the studs. Do not use motor oil or other low-quality lubricants. PRELOAD (TORQUE) RECOMMENDATIONS 7. Following the manufacturer-recommended torque sequence tighten the nuts in steps 1-3 Step 1: Tighten to 20 ft-lbs. Step 2: Tighten to 40 ft-lbs. Step 3: Tighten to 60 ft-lbs. With the included ARP Ultra-Torque fastener assembly lubricant

Show More Show Less

Schrick Performance Camshaft Set - 238/272 - F80 M3, F82/83 M4 S55 ...

T#:637691

Part#: SCHCSSS55238/272

Back Ordered

$ 1,899.99 USD

Add to Wish List

Qty

$ 1,899.99 USD

Add to Wish List

High-performance camshafts are key to increasing the top-end power output of your S55 engine at high boost. 238/272 degree, 10.6mm/10.5mm lift. Perfectly compatible with OE valves, springs, VANOS, Valvetronic etc

Show More Show Less

Sprocket - Double Gear

T#:5215978

Part#: 13528642165

Special Order: No Guaranteed ETA

$ 47.99 USD

Add to Wish List

Qty

$ 47.99 USD

Add to Wish List

ARP Head Stud Kit B48 Undercut CA625+, 12pt

T#:48367044

Part#: 401-4704

Ships on Sep 1, 2026

$ 588.99

This product was last offered at the strikethrough price on
08-13-2026

$ 529.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 588.99

This product was last offered at the strikethrough price on
08-13-2026

$ 529.99 USD

Limited Qty Sale

Add to Wish List

MINI 1.6 W10/W11 Engine ARP Head Stud Kit

T#:212677

Part#: 201-4301

In Stock

$ 156.99 USD

Add to Wish List

Qty

$ 156.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Converting from the factory BMW/MINI head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following MINIs:
2002-2006 R50 MINI MINI Cooper
2002-2006 R53 MINI MINI Cooper S

Show More Show Less

MINI R56 N18 Adjustment Unit - Outlet Cam

T#:8169510

Part#: 11367536085

In Stock

Sale - Save 25% $ 106.99

This product was last offered at the strikethrough price on
05-03-2026

$ 79.99 USD

Add to Wish List

Qty

Sale - Save 25%

$ 106.99

This product was last offered at the strikethrough price on
05-03-2026

$ 79.99 USD

Add to Wish List

MINI R56 N18 Adjustment Unit - Outlet Cam is a crucial component for optimizing engine performance. This timing chain camshaft gear, which is the thicker gear positioned toward the front of the engine on the outlet side, plays a key role in the timing and operation of the engine. It is typically replaced when servicing or replacing the timing chain to ensure proper engine function and longevity. As an Original Equipment Supplier (OES) part, it guarantees the same quality and reliability as the factory-installed component.

Thicker Gear Design: Ensures robust performance and durability.
Optimal Positioning: Located toward the front of the engine on the outlet side for precise timing.
Replacement Component: Commonly changed during timing chain replacement to maintain engine performance.
OES Quality: Provides factory-level quality and reliability.

Show More Show Less

Project Cars

SELECT YOUR BMW

Sub-Categories

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results