BMW Tools & Specialty Equipment for BMW Z Series G29 (2019+)

This tool comes in handy especially when working with an engine harness. Certain areas are always prone to corrosion and this tool makes having to re-pin a connector a breeze.

Unlike small screwdrivers, picks, and paper clips, these tools are the correct size and shape to remove and install tiny electrical pins and terminals at plastic block connectors with ease, and will not damage the connectors in the process.

Packaged in a blow molded case to keep everything secure and organized.

Protect your finish when working under the hood with a high quality Turner fender cover. Made from a synthetic leather layer with a goose flannelette backing for durability and protection. The Turner fender cover holds a tight grip to your fender or core support with four 9.5" magnets sewn into the top layer.

Features:

• Durable synthetic leather with the Turner logo
• Soft goose flannelette backing
• Four 9.5" integrated magnets

Dimensions:

•  Extra Long 20" x 47"

PRESSURE BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

FLUID CATCH BOTTLE:

keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Proper torque is very important when it comes to working on engines. The importance comes from proper sealing and to keep from damaging threads.

Features:

• Reversible ½-inch drive click-to-stop
• Torque range of 10 to 150 ft-lb
• Accurate to within +/-4%
• 18 inches in length with a convenient carry case

The perfect kit containing most of your needed European essentials. 

Features:

• 13PCS-1/4" DR.6PT SOCKETS: 4, 4.5 , 5 ,5.5 ,6 , 7, 8 ,9 ,10, 11, 12, 13, 14MM 
• 1PC- 1/4" DR. QUICK RELEASE RATCHET (72T).
• 2PC- 1/4" DR.50 & 100MM EXTENSIONS 
• 1PC- 1/4" DR.150MM FLEXIBLE EXTENSION
• 1PC- 1/4" DR.UNIVERSAL JOINT
• 1PC- 1/4" DR.SLIDING T-BAR
• 1PC- 1/4" DR.6" SPINNER HANDLE
• 1PC- 1/4" DR.1/4" BIT HOLDER ADAPTER
• 4PCS-HEX KEY WRENCHES:1.27, 1.5,2,2.5MM
• 6PCS-1/4" HEX SOCKETS:3,4,5,6,7,8MM
• 3PCS-1/4' SLOTTED SOCKETS:4,5.5,7MM
• 3PCS-1/4" PHILIPS SOCKETS:PH1, PH2, PH3
• 3PCS-1/4"POZI SOCKETS: PZ1, PZ2, PZ3
• 6PCS-1/4" TORX SOCKETS: T10, T15, T20, T25, T30, T40

Own an E30? This tool kit is a perfect fit for your glovebox!

This large socket is the perfect tool for axle nuts when servicing the axle shafts or wheel bearings.

Features:

• ½-inch drive 46mm 12-point socket
• Specially hardened to take the added abuse from a impact gun
• Coated for added protection and so you can tell it apart from non impact rated sockets
• 75mm depth  to accommodate many applications and different length shafts
• Made of durable chrome moly steel

Tired of busting your knuckles from old hardened exhaust hangers?

This Schwaben tool removes the hanger by pressing on the steel hanger bracket and pulling the rubber hanger in one motion. Self centering force pin locks onto the pin while the flat paddle pulls off the rubber hanger from behind. Slim profile and a 25 degree offset works in tight areas.

If you're removing trim panels and don't want to scratch or break any pieces then this is a must have. Formed for precision and constructed from plastic to be gentle with the finish.

Features:

•  Wide type remover
• Pull type remover
•  Handy remover
• Narrow type remover
• Upholstery Clip remover
• Angled Clip Panel Remover
• Fork Tip Flat Clip Panel Remover
• Clip Panel Remover
• Sharp Tip Flat Clip Remover
• Panel Remover
• Blunt Tip Flat Clip Panel Remover

The Schwaben aluminum wheel hanger makes it easy to remove and install wheels. Just thread the hanger stud into a wheel bolt hole and hang the wheel safely while you rotate tires or remove them for service or vehicle repair. (It's also great for keeping wheel bolt holes aligned on cars with spacers.)

Features:

• Longer & Lighter
• Made of 6061-T6 aluminum
• Anodized for hardness and good looks
• Knurled, non-slip handle has a drilled hole so you can hang it on a pegboard hook in your garage

This professional-grade deluxe fender roller allows you to gently and gradually flatten your inner fender lips in order to increase your fender to tire clearance.

This new deluxe fender roller has been designed to fit most applications.

This is the perfect tool for:

If you want to lower your vehicle
If you want wider-than-stock wheels
If you are going to use wheel spacers or decreased offset
Will work with bolt patterns of 4x100 and 5x100 up to 4x114.3 and 5x130 with 12mm or 14mm lug bolts.

By rolling the fender lip flat, you can lower your car further, and give your car a wider stance, without your tires rubbing on the inside of the fender.

Fully adjustable for use on vehicles of different ride heights, offsets, and wheel bolt patterns.

Use of a heat gun is recommended to soften the fender surface during the rolling process and prevent paint cracking.

Custom exhaust work in the plans? The Schwaben Exhaust Pipe Cutter will help you cut out old pipe or cut down new pipe with ease. It can cut any pipes from 3/4" to 3" in diameter and cuts pipe with only 1/4 turn adjustments, thanks to 15 blades that effectively cut the entire pipe with little movement. This is great for tight to reach places that prevents you from using more traditional non-specialty tools.

Features:

• Cuts from 3/4" pipe up to 3" pipe
• 15 cutting blades
• Rubber covered handles for grip and comfort

This complete set of extra deep sockets work great on cars equipped with extended studs. They also work as a long wheel nut socket for those deeply recessed nuts in wheels.

Features:

• 17mm, 19mm and 21mm socket in a sturdy blow molded case
• All sockets are 1/2" drive and a full 5-15/16 ( 150MM ) long
• Sockets are designed with inner bore to accept a 5" long stud

The Schwaben Dual Temperature Heat Gun Kit is the ideal tool for stripping paint, removing decals, shrinking wire wrap, etc. The heat gun has a switch which allows for two different heat settings (572F and 932F).

Features:

Four airflow adapters, 1pc Large Deflector Nozzle, 1pc Reduction Nozzle, 1pc Small Deflector Nozzle, and 1pc Reflector Nozzle.
Voltage 120C, 60 HZ
Amps 12.5A
Two heat settings: Low Heat up to 572 Degree F. High Heat 932 Degree F.
Air Volume: Low Heat: 10 cfm (280L/min) High Heat: 17 cfm (480 L/min)
Wattage: Low Heat: 1000W High Heat: 1500W
Has 6.75 Ft cord.
Built in hook to hang on wall.
For California Prop 65 warning see: www.P65Warnings.ca.gov. and photo below.

All the right bits in one box. The perfect assortment to keep the job going.

Features:

• 10 fractional SAE hex, 9 Torx® tamper-proof, 9 Torx®

• 9 Metric hex bits, 9 slotted bits, 8 Pozi-drive, 8 Phillips, 4 square-recess, 4 tri-wing

• 3 spline, 3 Torq, 3 clutch, wing-nut driver, magnetic bit holder and socket bit holder

• Made of hardened Chrome Vanadium steel for years of dependable use

• Packaged in a handy blow molded case with individually marked bit slots for easy organization