BMW Tools & Specialty Equipment for MINI

Our 3/8-inch drive, 36mm, 6-point socket grips tight and won’t slip. Low profile oil filter housing removal socket fits in tight places. 

• BMW M52 and M54
• MINI Gen 1 (R50, R52, and R53)

Our aluminum wheel hanger makes it easy to remove and install wheels. Just thread the hanger stud into a wheel bolt hole and hang the wheel safely while you rotate tires or remove them for service or vehicle repair. (It's also great for keeping wheel bolt holes aligned on cars with spacers.)

Features:

• Longer & Lighter
• Made of 6061-T6 aluminum
• Anodized for hardness and good looks
• Knurled, non-slip handle has a drilled hole so you can hang it on a pegboard hook in your garage

Better still, order two: one for your garage and another for the emergency tool kit in you trunk.

Safety is always the most important factor when it comes to working under your car, jack stands are highly recommended. 

Features:

• Ultra light  jack stands only weigh 4.7 lbs each
• All aluminum construction with heavy-duty  flanged bases to safely stabilize loads
• 6 locking positions for a secure load in multiple heights
• Extra heavy duty load pin at .584 in. diameter with a posi lock ball to insure it stays in place
• Min. Height is 10.6
• Max Height is 15.4"
• Large 7" diameter base
• Outer support tube is 2-1/8" in diameter

The Schwaben Piston Ring Filer is a vital tool for obtaining the precise end gap necessary for optimal piston ring performance.

This filer allows you to swiftly and accurately file piston rings to exact measurements, enhancing your engine’s efficiency and lifespan. By simply positioning the piston ring and turning the handle, you can easily rotate the abrasive wheel for a smooth and effective filing process.

**Note:** For the Schwaben Universal Piston Ring Compressor, check out T25805755!

Key Features:

• Optimize Performance: Achieve the perfect end gap crucial for top engine efficiency.
• Quick and Precise: File rings to exact specifications with ease.
• Easy Operation: Position the piston ring and turn the handle to effortlessly rotate the abrasive wheel.
• Enhanced Engine Longevity: Accurate end gaps contribute to longer engine life and better performance.

Instructions:

1. Position the Ring: Place the piston ring on the outer edge against the stop and align the ends squarely against the grinding wheel. Apply light, even pressure against the wheel to prevent grinding too large a gap.
2. Operate the Tool: Turn the handle so the grinding wheel turns towards the inside edge of the ring (counter-clockwise when viewed from the handle side of the tool).
3. Exercise Caution: This is a diamond grinding wheel. It cuts fast!

Checking Piston Ring Gap:

1. Deburr the Ring Ends: Carefully remove any burrs on the ring ends before placing the ring in the bore. A light touch with a fine abrasive stone works well.
2. Clean the Rings: Thoroughly clean the rings with lacquer thinner or acetone, as the paint coating from the factory may occasionally scratch the cylinder bore. Always wear gloves during this process.
3. Position the Ring in the Cylinder: Place the ring squarely in the cylinder bore, about 1" down from the deck surface. An upside-down flat-top piston will help you properly square the ring.
4. Measure the End Gap: Use a feeler gauge to measure the ring's end gap. Apply light grinding pressure and check frequently to avoid making the end gap too large.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

The Schwaben Dual Temperature Heat Gun Kit is the ideal tool for stripping paint, removing decals, shrinking wire wrap, etc. The heat gun has a switch which allows for two different heat settings (572F and 932F).

Features:

Four airflow adapters, 1pc Large Deflector Nozzle, 1pc Reduction Nozzle, 1pc Small Deflector Nozzle, and 1pc Reflector Nozzle.
Voltage 120C, 60 HZ
Amps 12.5A
Two heat settings: Low Heat up to 572 Degree F. High Heat 932 Degree F.
Air Volume: Low Heat: 10 cfm (280L/min) High Heat: 17 cfm (480 L/min)
Wattage: Low Heat: 1000W High Heat: 1500W
Has 6.75 Ft cord.
Built in hook to hang on wall.
For California Prop 65 warning see: www.P65Warnings.ca.gov. and photo below.

The Schwaben 1/4" Drive 6 Point Deep Socket Set comprises thirteen 1/4" deep metric sockets, each featuring 6-point heads specially crafted for navigating those tricky, confined spaces. With a length of 50mm, these sockets ensure you can reach critical areas with ease.

Furthermore, our LIFETIME REPLACEMENT program provides you with added assurance, ensuring enduring performance and value. Improve your toolkit with the Schwaben 1/4" Drive 6 Point Deep Socket Set and confidently tackle any task at hand.

Features:

Access Tight Spaces: These deep sockets, measuring 50mm in length, are expertly designed to reach challenging, confined areas, making them perfect for intricate tasks.

Organized Storage: Included in the set is a practical sliding rail socket holder, helping you maintain a tidy and easily accessible socket arrangement.

Enhanced Grip: Knurled rings encircling the socket bodies ensure a secure hold, even when hands and sockets are covered in oil or grease, minimizing the risk of accidents.

Optimal Torque: The sockets are equipped with corner radii for superior torque distribution, safeguarding fasteners from damage and ensuring efficient performance.

High-Quality Material: Crafted from robust chrome vanadium steel (CR-V), these sockets offer superior wear resistance and toughness compared to high-speed steel, guaranteeing durability and extended lifespan.

Satin Chrome Finish: Not only do the sockets feature an attractive satin chrome finish, but they also provide excellent corrosion resistance, ensuring long-term quality.

Lifetime Replacement: Supported by our lifetime replacement program, this set delivers enduring value and peace of mind, making it a wise addition to your toolkit investment.

Includes:

• 4 mm
• 4.5 mm
• 5 mm
• 5.5 mm
• 6 mm
• 7 mm
• 8 mm
• 9 mm
• 10 mm
• 11 mm
• 12 mm
• 13 mm
• 14 mm