BMW Z4 M Roadster S54 (2003-2008)

This tool comes in handy especially when working with an engine harness. Certain areas are always prone to corrosion and this tool makes having to re-pin a connector a breeze.

Unlike small screwdrivers, picks, and paper clips, these tools are the correct size and shape to remove and install tiny electrical pins and terminals at plastic block connectors with ease, and will not damage the connectors in the process.

Packaged in a blow molded case to keep everything secure and organized.

When doing work where the mounts and support need to be removed from the engine or transmission having a engine support bar is wise. By using this engine support the stress is coming off of whatever components are still attached reducing future unnecessary repairs. The safety side of it is having the heavy engine and transmission firmly supported as it should be instead of questionable jack techniques.  

Features:

•  2" longer than most
• Deluxe transverse support for even more stability
•  Two angle chain hooks for safer and more stable chain support 
•  61" long and fully adjustable to any width
•  Weight rating is a full 1000 lbs.
•  Includes four rubber padded feet to prevent slipping and damage to cars finish 
• This tool features a dual hook design for holding engine or transmission in place
•  Powder coated for long life and durability

Note: It is important that chains are hooked to both sides of hook, like in photo to insure load is supported evenly. 

This professional-grade deluxe fender roller allows you to gently and gradually flatten your inner fender lips in order to increase your fender to tire clearance.

This new deluxe fender roller has been designed to fit most applications.

This is the perfect tool for:

If you want to lower your vehicle
If you want wider-than-stock wheels
If you are going to use wheel spacers or decreased offset
Will work with bolt patterns of 4x100 and 5x100 up to 4x114.3 and 5x130 with 12mm or 14mm lug bolts.

By rolling the fender lip flat, you can lower your car further, and give your car a wider stance, without your tires rubbing on the inside of the fender.

Fully adjustable for use on vehicles of different ride heights, offsets, and wheel bolt patterns.

Use of a heat gun is recommended to soften the fender surface during the rolling process and prevent paint cracking.

Here's what makes this floor jack the best on the market:

• Dual pump pistons to reach maximum height in 5 pumps
• Low profile design keeping lowered cars in mind
• Easy maneuverability 
• Two piece quick release padded handle for storage or transport.

Details:

• Jack Capacity 2 Ton
• Max Lift Height 20"
• Low Height 3.25"
• Chassis Length 26.5"
• Overall Width 13"
• Saddle Diameter 4.5"
• Handle Length 50"
• Shipping Weight 50 lbs

This gauge ensures that the inlet and exhaust cams are aligned perfectly. Make sure the edges are on the correct sides of the cylinder head before using.

Includes two alignment pin's which is ideal for inspection and servicing the motor with the timing chain still attached. If you are going to be removing the timing chain for service, you will need to lock both cams. 

The Ultimate kit includes every thing the standard kit does along with, a second alignment bridge, flywheel lock pin, VANOS alignment tools. and 4 bolt crank socket.

This tool fits all S54 powered BMW, including: 
2001-2006 E46 BMW M3
2001-2002 E36/7 BMW Z3M Coupe Z3M Roadster
2006-2008 E85/6 BMW Z4M Coupe Z4M Roadster
 

If your clutch switch is bad, it will prevent the car from starting and seem similar to a bad starter, you will turn the key and nothing will happen. Replace yours to start your vehicle again.

Genuine BMW Module, Clutch Switch
This item fits the following BMW Chassis:
E39 M5,E46 M3,E85 Z4M,E39,E46,E85 Z4,E86 Z4
 

When it comes to the torque found on axle nuts you're already looking at using a breaker bar or impact gun not to mention the corrosion collected over the years. The safest approach is using impact socket, since they are built with the strength needed to avoid breaking under pressure.

Features:

• Heavy duty ½ inch-drive sockets and drivers have extra thick alloy steel walls, and take a beating that would destroy normal sockets
•  Durable black oxide coating wipes clean easily and resists rust
• Contains three 12-point sockets for a sure grip on the most common sized axle nuts, plus three hex drives for removing common hex-head plugs and fasteners
• Conveniently packaged in a blow molded case, this set will please the most demanding professional technician or discriminating prosumer

Kit includes:

• 30mm, 32mm, and 36mm - 12-point axle nut sockets - ½" drive

• 14mm, 17mm, and 19mm hex head drive axle shoulder bolt sockets - ½" drive

These pads were originally equipped on the Euro E46 M3 models and the US M3 ZCP, as well as Euro-spec M models from the 1990s. Owners of the E46 M3 will know that the stock pads are already quite 'aggressive' from the factory with a lot of initial bite. The initial bite was built into the pad to stop criticism of BMW's lack of 'performance' brakes. Instead of building the M models with exotic - and expensive - multi-piston calipers, BMW engineers turned up the braking power in their pads. These pads go a step further as the pads that originally came on the Euro E46 M3 and all E46 M3 ZCPs. For the street, these are excellent brake pads with excellent feel and performance. The only downside is the dust that comes from an organic pad. The problem with many aftermarket and OEM pads is that they do not match the same level of initial bite as the stock OE BMW pads. This can make the brakes feel 'weak' and 'numb' even though the pads are working properly. If you want to maintain your braking feel, these are the best to use.

Although these pads were originally designed for M cars, they fit other models as well, making them a great first-step upgrade for better braking.

Price is for one set of pads - enough to replace the pads on both front calipers.

If you are looking for front brake rotors, 2282445446

These front pads fit the following BMWs:
1988-1994 E32 BMW 735i 735il 740i 740il 750il (more aggressive fitment)
1989-1995 E34 BMW 525i 530i 535i 540i M5 (more aggressive fitment)
1994-1998 E36 BMW M3 (more aggressive fitment than US-spec)
1998-2002 Z3 BMW M Roadster M Coupe (more aggressive fitment)
1999-2005 E46 BMW 330i 330ci 330xi M3 (more aggressive fitment for 330)
2003-2008 E85 E86 BMW Z4 3.0si Z4 M Roadster M Coupe (more aggressive fitment for 3.0si)