Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 215mm (8.46") to 275mm (10.82") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints(M10x1.5): Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability

Our sealed Monoball Rear Trailing Arm Bushings (RTAB) are the best solution for completely eliminating deflection and unwanted toe changes on the rear of the E36, E46, and Z4. While rubber and urethane bushings flex during load, the toe can change widely giving you nervous and unpredictable handling. These RTABs have a solid aluminum housing with a high-quality sealed OE bearing. These bushings were developed from years of competition use in various racing and HPDE events. There is simply no better RTAB unless your racing class rules prohibit the use of mono or spherical bearings.

The rear trailing arm bushings take a lot of abuse from acclerating, braking and cornering. The stock rubber bushings are just not up to the task of keeping rear wheel alignment in spec for very long, especially if you have upgraded to stickier tires and a better suspension. The pliable rubber flexes and twists which slows down reaction time and leaves you with a car that feels nervous and 'tail happy'. Urethane helps to control the alignment but issues with fitment, maintenance, and longevity keep us from recommending urethane on anything but a street car. We also offer a Delrin RTAB for cars that must conform to certain racing class rules. These sealed spherical bearings are the best at controlling rear toe alignment.

Our aluminum RTABs are very well made - high grade aluminum alloy and steel CNC'd out of a billet by an ISO 9001 certified manufacturer, each component is either hardcoated or nickel plated. While multiple manufacturers offer two piece designs, our research showed that a one piece bushing is a better design featuring a sealed bearing to keep contaminants out extending the life of the bearing.

Features:

Key Benefits:

• Rear Trailing Arm Monoball eliminates unwanted deflection, maintaining alignment settings and minimizing wheel hop.
• Allows full rear trailing arm articulation for low friction movement and eliminates binding found in rubber and poly bushings.
• Completely streetable: utilizes an OES Lemforder brand sealed, greased ball joint for an extremely long service life with no increase to NVH.

Design Features:

• Housing: Billet CNC 6061-T6 aluminum, type II anodized for exceptional durability and corrosion resistance
• Bearing: OE Mercedes/lemforder 2043520027 Sealed ball joint
• Bearing inserts: CNC machined 303 stainless steel.
• Rebuildable

Clickhere for installation instructions.

This item fits the following BMWs:
1992-1998 E36 BMW 318i 318is 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
2003-2008 Z4 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe

Click here for installation instructions.

Worn rubber differential mounts will lead to the differential twisting and shifting around in the rear subframe. Not only will this be noisy but it's bad for driver confidence and bad for the chassis as well. Even on fresh rubber bushings the differential has deflection and twist, especially if the car has been modified for more torque. Since the differential is centrally mounted in the rear subframe, with all suspension mounts interconnected, a differential with too much deflection will affect handling and could even damage the rear subframe.

These 88A urethane E46 M3 diff mounts are much stiffer than stock but still not as solid as our Turner aluminum/Delrin bushings. This set will resist twisting much better than the stock rubber mounts. Included is the front diff mount and two rear mounts in the cover.

The E36/E46 rear trailing arm bushings (RTABs) wear out faster than any other bushing on the car. Worn RTAB will cause excessive toe alignment change and give a 'loose' or 'floaty' feeling in the rear handling. One of the reasons for this is that they over-extend during motion, stretching and twisting the rubber in all directions. These shims sit on either side of the bushing and limit the amount of extension from the bushing. Not only will you get more life from your RTAB but these will help stiffen the bushing during cornering. But during normal driving you will still have all of the comfort of the stock rubber bushings. These part about these bushings is how easy they are to install - simply slide them in place during your bushing install. They can be added to pre-installed bushings too by dropping the trailing arm and removing the cage around the bushing.

Works with stock rubber bushings only (not urethane or Delrin).

Fine-tuning your coilover damping shouldn’t mean stripping out your rear seats or interior panels. On many applications, rear shock adjusters are hidden behind carpet, trim, or seatbacks, making quick adjustments a hassle.

The ECS Rear Damping Extension Kit solves that problem with a clean and functional solution. These flexible extensions relocate the adjustment knobs to an easily accessible point above the rear shock towers, letting you dial in your suspension from inside the cabin, no disassembly required.

Installation is straightforward: simply drill a small access hole in your interior trim and route the extension cables through. The adjustment knobs can be removed to allow the line to pass through smaller openings, minimizing cutting. For proper installation, be sure to fully loosen the set screw, insert the cable, then securely tighten it using the provided Allen key.

Kit Includes:

(2) Rear damping adjuster extension cables

Installation hardware and Allen key

A smart upgrade for track cars, daily drivers, or anyone who values easy access to suspension tuning, without compromising interior fit and finish.

Want a race-spec rear shock mount but with the comfort of a factory bushing? This ECS rear shock mount combines the precision and articulation of a spherical bearing with the isolation of urethane bushings. The stainless monoball bearing is lined with PTFE lubricant and suspended in 80A urethane and housed in a hard anodized 6061-T6 aluminum mount. The spherical bearing is a better design than most rear shock mounts because it allows the shock to move and tilt without side-loading the shock shaft (which leads to premature failure of the shock). Most Genuine BMW and aftermarket shock mounts are not designed for shock angles and the stress that track or performance driving will put on the shock shaft. The ECS shock mount is properly designed to handle these loads. The internal bearing is also replaceable - it will be years before you have to replace the entire mount. The ECS mount is fully encapsulated to prevent the common shock mount failure of the stock mount design.

ECS RSM features:

• Maintenance free, PTFE lined, stainless steel monoball spherical bearing for full shaft articulation
• 80A polyurethane isolation bushings for NVH control
• Accommodates 10mm, 12mm, or 14mm damper shafts
• Fully constrained shaft mount makes RSM blow out impossible
• Hard anodized 6061-T6 construction
• Fully rebuildable design

* - the RSM comes with the BMW standard 10mm shock shaft bushings. 12mm is used on some performance shocks and 14mm is used on some true motorsport rear shocks.

Revamp Your Suspension with the BMW & MINI Coilover Wrench Set

• Compatible with BMW and MINI models for versatile use
• Durable construction ensures long-lasting performance
• Ergonomic design provides comfortable handling during installation
• Allows for precise adjustment of coilovers for optimal ride quality

Upgrade your BMW or MINI's suspension system with the BMW & MINI Coilover Wrench Set. This set is compatible with various BMW and MINI models, offering versatile compatibility for a wide range of vehicles. Constructed from durable materials, these wrenches are built to withstand the rigors of frequent use and provide long-lasting performance. The ergonomic design ensures comfortable handling during installation, reducing fatigue and allowing for more efficient work. With the BMW & MINI Coilover Wrench Set, you can easily adjust your coilovers to achieve the optimal ride quality for your vehicle.