BMW Tools & Specialty Equipment for BMW E12 530i M30 3.0L

Protect your finish when working under the hood with a high quality Turner fender cover. Made from a synthetic leather layer with a goose flannelette backing for durability and protection. The Turner fender cover holds a tight grip to your fender or core support with four 9.5" magnets sewn into the top layer.

Features:

• Durable synthetic leather with the Turner logo
• Soft goose flannelette backing
• Four 9.5" integrated magnets

Dimensions:

•  Extra Long 20" x 47"

Proper torque is very important when it comes to working on engines. The importance comes from proper sealing and to keep from damaging threads.

Features:

• Reversible ½-inch drive click-to-stop
• Torque range of 10 to 150 ft-lb
• Accurate to within +/-4%
• 18 inches in length with a convenient carry case

Proper torque is very important when it comes to working on engines. The importance comes from proper sealing and to keep from damaging threads.

Features:

• Reversible 3/8"-inch drive click-to-stop
• Torque range of 5 to 80 ft-lb
• Accurate to within +/-4%

Our aluminum wheel hanger makes it easy to remove and install wheels. Just thread the hanger stud into a wheel bolt hole and hang the wheel safely while you rotate tires or remove them for service or vehicle repair. (It's also great for keeping wheel bolt holes aligned on cars with spacers.)

Features:

• Longer & Lighter
• Made of 6061-T6 aluminum
• Anodized for hardness and good looks
• Knurled, non-slip handle has a drilled hole so you can hang it on a pegboard hook in your garage

Better still, order two: one for your garage and another for the emergency tool kit in you trunk.

The perfect kit containing most of your needed European essentials. 

Features:

• 13PCS-1/4" DR.6PT SOCKETS: 4, 4.5 , 5 ,5.5 ,6 , 7, 8 ,9 ,10, 11, 12, 13, 14MM 
• 1PC- 1/4" DR. QUICK RELEASE RATCHET (72T).
• 2PC- 1/4" DR.50 & 100MM EXTENSIONS 
• 1PC- 1/4" DR.150MM FLEXIBLE EXTENSION
• 1PC- 1/4" DR.UNIVERSAL JOINT
• 1PC- 1/4" DR.SLIDING T-BAR
• 1PC- 1/4" DR.6" SPINNER HANDLE
• 1PC- 1/4" DR.1/4" BIT HOLDER ADAPTER
• 4PCS-HEX KEY WRENCHES:1.27, 1.5,2,2.5MM
• 6PCS-1/4" HEX SOCKETS:3,4,5,6,7,8MM
• 3PCS-1/4' SLOTTED SOCKETS:4,5.5,7MM
• 3PCS-1/4" PHILIPS SOCKETS:PH1, PH2, PH3
• 3PCS-1/4"POZI SOCKETS: PZ1, PZ2, PZ3
• 6PCS-1/4" TORX SOCKETS: T10, T15, T20, T25, T30, T40

Own an E30? This tool kit is a perfect fit for your glovebox!

If you're removing trim panels and don't want to scratch or break any pieces then this is a must have. Formed for precision and constructed from plastic to be gentle with the finish.

Features:

•  Wide type remover
• Pull type remover
•  Handy remover
• Narrow type remover
• Upholstery Clip remover
• Angled Clip Panel Remover
• Fork Tip Flat Clip Panel Remover
• Clip Panel Remover
• Sharp Tip Flat Clip Remover
• Panel Remover
• Blunt Tip Flat Clip Panel Remover

This large socket is the perfect tool for axle nuts when servicing the axle shafts or wheel bearings.

Features:

• ½-inch drive 46mm 12-point socket
• Specially hardened to take the added abuse from a impact gun
• Coated for added protection and so you can tell it apart from non impact rated sockets
• 75mm depth  to accommodate many applications and different length shafts
• Made of durable chrome moly steel

These weld protectors allow you to safely jack up your vehicle without crushing or bending any pinch welds. These will fit any jack and will work with many jack stands such as the Schwaben Aluminum Jack Stands.

Specifications:

• 3" wide
• 1" tall
• Single groove top
• Double grooved bottom

This complete set of extra deep sockets work great on cars equipped with extended studs. They also work as a long wheel nut socket for those deeply recessed nuts in wheels.

Features:

• 17mm, 19mm and 21mm socket in a sturdy blow molded case
• All sockets are 1/2" drive and a full 5-15/16 ( 150MM ) long
• Sockets are designed with inner bore to accept a 5" long stud

The Schwaben Dual Temperature Heat Gun Kit is the ideal tool for stripping paint, removing decals, shrinking wire wrap, etc. The heat gun has a switch which allows for two different heat settings (572F and 932F).

Features:

Four airflow adapters, 1pc Large Deflector Nozzle, 1pc Reduction Nozzle, 1pc Small Deflector Nozzle, and 1pc Reflector Nozzle.
Voltage 120C, 60 HZ
Amps 12.5A
Two heat settings: Low Heat up to 572 Degree F. High Heat 932 Degree F.
Air Volume: Low Heat: 10 cfm (280L/min) High Heat: 17 cfm (480 L/min)
Wattage: Low Heat: 1000W High Heat: 1500W
Has 6.75 Ft cord.
Built in hook to hang on wall.
For California Prop 65 warning see: www.P65Warnings.ca.gov. and photo below.

The Schwaben Piston Ring Filer is a vital tool for obtaining the precise end gap necessary for optimal piston ring performance.

This filer allows you to swiftly and accurately file piston rings to exact measurements, enhancing your engine’s efficiency and lifespan. By simply positioning the piston ring and turning the handle, you can easily rotate the abrasive wheel for a smooth and effective filing process.

**Note:** For the Schwaben Universal Piston Ring Compressor, check out T25805755!

Key Features:

• Optimize Performance: Achieve the perfect end gap crucial for top engine efficiency.
• Quick and Precise: File rings to exact specifications with ease.
• Easy Operation: Position the piston ring and turn the handle to effortlessly rotate the abrasive wheel.
• Enhanced Engine Longevity: Accurate end gaps contribute to longer engine life and better performance.

Instructions:

1. Position the Ring: Place the piston ring on the outer edge against the stop and align the ends squarely against the grinding wheel. Apply light, even pressure against the wheel to prevent grinding too large a gap.
2. Operate the Tool: Turn the handle so the grinding wheel turns towards the inside edge of the ring (counter-clockwise when viewed from the handle side of the tool).
3. Exercise Caution: This is a diamond grinding wheel. It cuts fast!

Checking Piston Ring Gap:

1. Deburr the Ring Ends: Carefully remove any burrs on the ring ends before placing the ring in the bore. A light touch with a fine abrasive stone works well.
2. Clean the Rings: Thoroughly clean the rings with lacquer thinner or acetone, as the paint coating from the factory may occasionally scratch the cylinder bore. Always wear gloves during this process.
3. Position the Ring in the Cylinder: Place the ring squarely in the cylinder bore, about 1" down from the deck surface. An upside-down flat-top piston will help you properly square the ring.
4. Measure the End Gap: Use a feeler gauge to measure the ring's end gap. Apply light grinding pressure and check frequently to avoid making the end gap too large.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.