BMW Tools & Specialty Equipment for BMW E12 530i M30 3.0L

This tool comes in handy especially when working with an engine harness. Certain areas are always prone to corrosion and this tool makes having to re-pin a connector a breeze.

Unlike small screwdrivers, picks, and paper clips, these tools are the correct size and shape to remove and install tiny electrical pins and terminals at plastic block connectors with ease, and will not damage the connectors in the process.

Packaged in a blow molded case to keep everything secure and organized.

Protect your finish when working under the hood with a high quality Turner fender cover. Made from a synthetic leather layer with a goose flannelette backing for durability and protection. The Turner fender cover holds a tight grip to your fender or core support with four 9.5" magnets sewn into the top layer.

Features:

• Durable synthetic leather with the Turner logo
• Soft goose flannelette backing
• Four 9.5" integrated magnets

Dimensions:

•  Extra Long 20" x 47"

PRESSURE BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

FLUID CATCH BOTTLE:

keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Our aluminum wheel hanger makes it easy to remove and install wheels. Just thread the hanger stud into a wheel bolt hole and hang the wheel safely while you rotate tires or remove them for service or vehicle repair. (It's also great for keeping wheel bolt holes aligned on cars with spacers.)

Features:

• Longer & Lighter
• Made of 6061-T6 aluminum
• Anodized for hardness and good looks
• Knurled, non-slip handle has a drilled hole so you can hang it on a pegboard hook in your garage

Better still, order two: one for your garage and another for the emergency tool kit in you trunk.

Protecta socket are used to keep ugly scratch marks from showing up after torqueing down wheel lugs.

Features:

• Coated six-point deep-well impact sockets 
• Color coded mar-free exterior coatings that prevent nicks and scratches left by plain metal sockets
• 17mm, 19mm and 21mm Sockets included

Use these with your breaker bar or impact gun to remove the tightest wheel bolts and lug nuts: when reinstalling wheels, use them to final torque wheel fasteners to factory specifications.

Combine these with our torque limiting sockets and the Schwaben ½-inch torque wrench for a complete wheel fastener solution.

If you're removing trim panels and don't want to scratch or break any pieces then this is a must have. Formed for precision and constructed from plastic to be gentle with the finish.

Features:

•  Wide type remover
• Pull type remover
•  Handy remover
• Narrow type remover
• Upholstery Clip remover
• Angled Clip Panel Remover
• Fork Tip Flat Clip Panel Remover
• Clip Panel Remover
• Sharp Tip Flat Clip Remover
• Panel Remover
• Blunt Tip Flat Clip Panel Remover

These weld protectors allow you to safely jack up your vehicle without crushing or bending any pinch welds. These will fit any jack and will work with many jack stands such as the Schwaben Aluminum Jack Stands.

Specifications:

• 3" wide
• 1" tall
• Single groove top
• Double grooved bottom

WHEEL STORAGE RACK:

Now you can stack your extra wheels without the danger of scratches and scuffs. This wheel storage rack keeps your wheels spaced apart, and being on locking casters, allows you to easily move the whole set anywhere in your garage or shop at one time. Sturdy steel construction and a wide base means this wheel rack won't tip over. Holds up to 275 lbs - enough for most any wheel & tire set.

Fits up to 8½" wide wheels, depending on offset

TIRE STACK COVER:

This tire stack by Schwaben is the solution to keeping your tires and wheels clean while in storage.

• Works with 4 tire stacks and works great with our Schwaben Wheel Tree (ES2710754).
• Durable 150D coated material is rated for outdoor use.
• Cover is a large 32" wide X 46" tall.
• Fitted with a long 29" zipper up the side for easy installation and removal.
• Nylon draw string at the bottom allows for a good snug fit.
• Includes a handy storage pouch if not in use.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Custom exhaust work in the plans? The Schwaben Exhaust Pipe Cutter will help you cut out old pipe or cut down new pipe with ease. It can cut any pipes from 3/4" to 3" in diameter and cuts pipe with only 1/4 turn adjustments, thanks to 15 blades that effectively cut the entire pipe with little movement. This is great for tight to reach places that prevents you from using more traditional non-specialty tools.

Features:

• Cuts from 3/4" pipe up to 3" pipe
• 15 cutting blades
• Rubber covered handles for grip and comfort

This hand held Schwaben tool makes changing fluids an easy, quick task.The Schwaben fluid suction/fill pump suitable for oils, water and any non corrosive liquid.

Features 

• Comes with a flexible and a rigid tube. 
• Flow rate is adjustable for different functions.
• 350 ML capacity
• Cylinder is marked in 20 mL increments and fraction of quarts for accurate filling. 

Not for use with gasoline.

Schwaben Oil Filter Removal Pliers / Wrench are designed to tackle the most stubborn spin-on filters with ease. Featuring large, adjustable jaws with raised teeth, these pliers provide a secure grip on a wide range of filter diameters. The long, plastic-coated handles offer a comfortable grip and added leverage, making filter removal straightforward and efficient.

• Efficient Removal: Handles the toughest oil filters with ease, thanks to its robust design.
• Versatile Fit: Adjustable jaws with raised teeth ensure a secure grip on various filter sizes.
• Comfortable Use: Long, plastic-coated handles provide a comfortable grip and extra leverage.
• Durable Construction: Built to last, ensuring reliable performance for frequent use.

Warning: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. For more information, visit Proposition 65.