BMW Engine Parts for BMW E30 M3 S14 2.3L

When we designed this catch we wanted to have the most function options available, the best separation method, and the easiest to service. The Turner engineered catch cans offer a pre-setup design based ion desired flow direction, however this does not limit you to this flow. The inner baffle orientation can be easily adjusted to flow in both directions in case you decide to move this catch can to a different vehicle. A 4 chamber system  baffle system inside the catch can was engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can. Having a closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation.

Our catch can was also designed with the idea that the cans fill level can easily be checked with a top mounted dipstick and an optional use bottom drain hole. The drain hole can be used with a valve and hose to be mounted at a lower area of the vehicle so when you're doing an oil change you can drain the catch can.

Features:

• 6061-T6 billet machined body, anodized black for lasting protection and appearance
• Strategically positioned 4 chamber baffle system maximizes oil / air separation 
• Knurled and black anodized oil dipstick makes inspecting oil volume of reservoir clean and simple
• Sealed with a pre-installed viton O-Ring
• Includes 2.5mm allen key to remove baffle plates for cleaning
• Engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can
• Closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation
• Optional use drain hole (valve and hose sold separately, watch for our model specific drain kits!)

This fuel tank hose runs from the filler neck to the inlet of the fuel tank. Due to years of exposure to water, salt, dirt, and general road debris, this hose is commonly rotted out causing a leak when filling the fuel tank.

If your hose is leaking, replace it with this high-quality, exact-fit piece from Bremmen Parts.

The Schwaben Piston Ring Filer is a vital tool for obtaining the precise end gap necessary for optimal piston ring performance.

This filer allows you to swiftly and accurately file piston rings to exact measurements, enhancing your engine’s efficiency and lifespan. By simply positioning the piston ring and turning the handle, you can easily rotate the abrasive wheel for a smooth and effective filing process.

**Note:** For the Schwaben Universal Piston Ring Compressor, check out T25805755!

Key Features:

• Optimize Performance: Achieve the perfect end gap crucial for top engine efficiency.
• Quick and Precise: File rings to exact specifications with ease.
• Easy Operation: Position the piston ring and turn the handle to effortlessly rotate the abrasive wheel.
• Enhanced Engine Longevity: Accurate end gaps contribute to longer engine life and better performance.

Instructions:

1. Position the Ring: Place the piston ring on the outer edge against the stop and align the ends squarely against the grinding wheel. Apply light, even pressure against the wheel to prevent grinding too large a gap.
2. Operate the Tool: Turn the handle so the grinding wheel turns towards the inside edge of the ring (counter-clockwise when viewed from the handle side of the tool).
3. Exercise Caution: This is a diamond grinding wheel. It cuts fast!

Checking Piston Ring Gap:

1. Deburr the Ring Ends: Carefully remove any burrs on the ring ends before placing the ring in the bore. A light touch with a fine abrasive stone works well.
2. Clean the Rings: Thoroughly clean the rings with lacquer thinner or acetone, as the paint coating from the factory may occasionally scratch the cylinder bore. Always wear gloves during this process.
3. Position the Ring in the Cylinder: Place the ring squarely in the cylinder bore, about 1" down from the deck surface. An upside-down flat-top piston will help you properly square the ring.
4. Measure the End Gap: Use a feeler gauge to measure the ring's end gap. Apply light grinding pressure and check frequently to avoid making the end gap too large.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Meet modern emission regulations while preserving engine performance with the ECS Baffled Oil Catch Can. Designed for BMW and MINI vehicles, this system efficiently captures blow-by gases, preventing excessive oil vapor ingestion into the intake tract. The innovative 4-chamber baffle system maximizes oil/air separation, reducing carbon build-up and pollutants. Featuring a 1/4" drain fitting for easy maintenance, this catch can minimizes oil deposits, ensuring cleaner emissions and enhanced engine performance.

Key Benefits:

• Efficient 4-chamber baffle system for maximum oil/air separation
• Recirculated design reduces oil ingestion, promoting cleaner emissions
• Durable 6061-T6 billet machined body with anodized black finish for longevity
• Integrated dipstick and sealed reservoir for easy oil inspection and maintenance
• Serviceable design with removable baffle plates for cleaning
• Easy installation with customizable mounting options and leak-free fittings
• Engineered and manufactured in the USA for superior performance and durability

Note: Not for sale or use in the state of California on any pollution-controlled vehicle as per the California Air Resources Board.