Turner Motorsport for BMW 5 Series E39 (1996-2003)

Over the years, it is not uncommon for exhaust tips to be damaged and corroded, becoming a "sore spot" of your BMW. To remedy this unsightly feature, we now offer our very own exhaust tips! Featuring stainless steel construction and a simple, yet sporty design, this exhaust tip will look perfectly at home on almost any model.

Features & Specifications:

3.0" Inner Diameter
4.0" Outer Diameter
Black Chrome Finish
Double Wall Construction
Straight Cut Style
Includes Stainless Steel Clamp

All vehicles will lose some degree of performance due to heat soak under the right operating conditions.  Engine management systems constantly monitor operating conditions and modifying parameters based on sensor inputs. BMW integrated the intake air temp sensor in the MAF housing on models such as the E39 M5, and, being sandwiched behind a hot radiator and in some applications next to an even hotter valve cover, this is less than ideal for performance applications. Absorbing excess heat from its surroundings, the MAF can’t shed it fast enough, and the ECU reads an inaccurately high intake air temperature. Compensating for this false hot air measurement, the ECU pulls timing and runs a richer fuel mixture, resulting in a significant loss of torque.

What can you do?  Locate an intake air temp sensor in a location where it can properly measure incoming air temps and where it's less prone to heat soak. Mounting the sensor further away from the heat source and isolating it from the MAF housing, it can both resist the effects of heat soak longer and respond to temperature changes more quickly.  The result is you’ll experience reduced torque loss and more consistent power output when you’re pushing your engine hard. 

The Turner engineering team was initially skeptical of the claimed performance benefits of this modification. They first set out validate the functionality and performance benefit of a temp sensor relocation. Replicating stop-and-go traffic heat soak in a 2001 540i was a simple task in a controlled environment - their dynometer. First the car was heat soaked to simulate being stuck in traffic or moving at low speeds by running the car four times on the dyno with the dyno's cooling fans disabled. The fans were then turned on for three more runs to observe the recovery rate once air flow was reintroduced. The test: following this procedure once with a stock IAT, and once with their relocation kit in place. 

The result? Turner recovered 11lb-ft torque at 2500rpm through use of their relocation kit, with even greater recovery to be found for M5 owners. Here are the heat soak-related torque losses Turner experienced:

Stock IAT location:
18rwtq at 2500rpm
10rwtq at 3000rpm
9rwtq at 3700rpm

Turner IAT Relocation:
7rwtq at 2500rpm
5rwtq at 3000rpm
5rwtq at 3700rpm

**Click here for installation instructions**

The Turner engineering team designed a complete plug and play kit (unlike all other options on the market) that makes for quick, easy, and reversible installation. Weather-sealed connectors keep out the elements, while sheathed wiring offers a clean appearance underhood. With a harness nearly 3 feet long - the Turner IAT relocation kit offers flexibility in positioning, but not too long that you're left with unsightly excess wiring. Turner recommends positioning the sensor in a location away from engine heat, but still within the intake ducting to achieve accurate intake temp readings - such as the far side of the base of the airbox. Vehicles with cold air intakes with cone-style filters can even position the sensor in the end of the filter. Simply drill a hole in your (cool) location of choice and plug in the harness. More information including installation instructions and some good examples of sensor mounting locations can be found in our DIY PDF. 

We include everything you need to relocate your IAT, just select your desired sensor brand below - Genuine BMW or original equipment Beru.

Also the perfect plug-n-play option for anyone looking to upgrade their intake to utilize an Alpha-N tune!

Note for vehicles with M62 engine: applicable to 1999 and up

Universal 2.5" inlet to 3.5" outlet exhaust tip. Priced per exhaust tip.

Over the years, it is not uncommon for exhaust tips to be damaged and corroded, becoming a "sore spot" of your BMW. To remedy this unsightly feature, we now offer our very own exhaust tips! Featuring stainless steel construction and a simple, yet sporty design, this exhaust tip will look perfectly at home on almost any model.

Features & Specifications:

Swivel feature for perfect alignment of the exhaust tips in the rear bumper
2.5" Inner Diameter
3.5" Outer Diameter
Mirror Chrome Finish
Double Wall Construction
Angle Cut Style
Includes Stainless Steel Clamp

Dual Tip Wall Slash Cut Exhaust - 3.0 Inlet - 3.5 OD - Stepped Left - Mirror is the perfect upgrade for those looking to enhance their vehicle's aesthetics and performance. Crafted with a stunning mirror finish, this exhaust tip features a sleek slash cut and stepped left design that adds a touch of sophistication to your vehicle. Its double-wall construction ensures durability and a premium look, making it a must-have for any car enthusiast.

• Enhanced Appearance: Mirror finish provides a polished, high-end look.
• Durable Construction: Double-wall design for long-lasting performance.
• Precision Fit: 3.0-inch inlet and 3.5-inch outer diameter for a perfect fit.
• Stylish Design: Slash cut and stepped left design for a unique, aggressive appearance.
• Easy Installation: Designed for straightforward installation on compatible vehicles.

When we designed this catch we wanted to have the most function options available, the best separation method, and the easiest to service. The Turner engineered catch cans offer a pre-setup design based ion desired flow direction, however this does not limit you to this flow. The inner baffle orientation can be easily adjusted to flow in both directions in case you decide to move this catch can to a different vehicle. A 4 chamber system  baffle system inside the catch can was engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can. Having a closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation.

Our catch can was also designed with the idea that the cans fill level can easily be checked with a top mounted dipstick and an optional use bottom drain hole. The drain hole can be used with a valve and hose to be mounted at a lower area of the vehicle so when you're doing an oil change you can drain the catch can.

Features:

• 6061-T6 billet machined body, anodized black for lasting protection and appearance
• Strategically positioned 4 chamber baffle system maximizes oil / air separation 
• Knurled and black anodized oil dipstick makes inspecting oil volume of reservoir clean and simple
• Sealed with a pre-installed viton O-Ring
• Includes 2.5mm allen key to remove baffle plates for cleaning
• Engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can
• Closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation
• Optional use drain hole (valve and hose sold separately, watch for our model specific drain kits!)

High performance ignition kit for your M54 featuring spark plugs, Turner high performance ignition coils and grease to make sure you have no issues at your next maintenance interval!

Our BMW ignition coils are designed with performance and efficiency in mind. An engine needs 3 main components to run (Air, Fuel, Spark.) Turner ignition coils are modified to increase energy output; more energy output results in a faster, more efficient and consistent burn to make sure your fuel is being utilized to its maximum potential. Our signature Turner ignition coils feature a blue housing that give your engine the performance and aesthetic your looking for.

Ignition coils should be changed every 40,000 - 60,000 miles and are an important maintenance item due to the essential role they play in your engines health, performance and efficiency. Choose Turner Ignition Coils to keep your engine running strong and healthy.

Features and Benefits:

Increased performance
New spark plugs and grease
Direct fitment
Signature Turner Blue ignition coils

Whether you are looking to replace your old stock wheel lug bolts, or need longer bolts to accommodate wheel spacers or for other special considerations, our silver wheel bolts are probably what you need. They are high grade (10.9) and feature a durable bright silver finish. These are 12 x 1.5mm bolts with a 17mm head -- as used on most BMWs. Replaces BMW part numbers 36136781150 and 36131095390.

The standard length wheel bolts are for stock BMWs, and the longer length bolts are listed below (select your length with the drop down box) with the size / thickness wheel spacers they are suitable for. Longer wheel bolts are only 20 cents more than standard, and are available in lengths to work with spacers up to 20mm thick. Please select your desired length below (default is the standard/stock BMW length bolt).

Price is for a set of 10 bolts.

These silver wheel bolts fit the following BMWs:
2008-2012 E82 BMW 128i 135i 1M Coupe
1977-1983 E21 BMW 320i 320/5 323i
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is 325ix M3
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2007-2013 E93 BMW 328i 335i M3 - Convertible
1982-1988 E28 BMW 524td 528e 533i 535i 535is M5
1989-1995 E34 BMW 525i 530i 535i 540i M5
1997-2003 E39 BMW 525i 528i 530i 540i M5
2004-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive 545i 550i M5
1982-1989 E24 BMW 633csi 635csi L6 M6
2004-2011 E63 E64 BMW 645ci 650i M6
1977-1987 E23 BMW 728i 733i 735i 745i L7
1988-1994 E32 BMW 735i 735il 740i 740il 750il
1995-2001 E38 BMW 740i 740il 750il
1990-1999 E31 BMW 840i 840ci 850i 850ci 850csi
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe
2009-2015 E89 BMW Z4 sDrive28i sDrive30i sDrive35i sDrive35is
2000-2003 E52 BMW Z8 Roadster
2002-6/2006 R50 MINI MINI Cooper
2005-6/2006 R52 MINI MINI Cooper Convertible, MINI Cooper S Convertible.
2002-6/2006 R53 MINI MINI Cooper S

Turner has developed a proprietary zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

The ULTIMATE shifter upgrade for your BMW! Experience more precise throws, less shift lever travel, and an all-around transformation in your shifting experience.

For dozens of years, enthusiasts have critiqued the imprecise and vague feeling of BMW manual transmissions. Plagued with long throws, fore and aft play in gear, and a generally loose feeling, your OEM BMW shifter leaves much to be desired. While most standard carrier-mount short throw shifter kits will aid in reducing throw length and eliminating side-to-side play in gear, some enthusiasts long for a hardcore, race-inspired shifter that completely removes play and excessive throw length. At Turner Motorsport we share the same desire and set out to offer the ULTIMATE upgrade with this Performance Chassis Mount Short Shifter.

WHY UPGRADE?

Factory BMW shifter assemblies are complex by nature. The main component of this assembly is the shift carrier, a cast aluminum piece positioned inside the transmission tunnel that incorporates bushings at both ends for mounting. Like most factory parts, these bushings are designed to reduce NVH (noise, vibration, and harshness) transmission to the cabin. To the spirited driver, however, these bushings translate to flex and vagueness in the shift lever. Moreover, because this carrier is mounted to both the transmission and the body, the entire shifter assembly will "float" with the driveline, further increasing the vague and imprecise feeling of your shifter.

Our Performance Chassis Mount Short Shifter removes the shift carrier assembly entirely—removing any prospect of flex caused by bushings or driveline movement. By contrast, this chassis mount shifter offers a drastic reduction in shift lever travel, vagueness, and side-to-side play. An elevated base allows for moving the fulcrum point upwards, resulting in a much shorter and more precise throw. Shift times are further reduced by a tall, "rally style" shift lever, used to aid in leverage while also bringing the lever closer to the steering wheel. Our design incorporates a proprietary centering spring design, which is adjustable for increasing or decreasing self-centering force. In short, this design eliminates all the drawbacks of your factory BMW shifter, translating to more control, greater precision, shorter throws, and faster shift times.

FEATURES & BENEFITS

Reduced Throw: Modified shifter geometry and heightened fulcrum point translate to a shorter shift lever throw
Improved Shifter Feel: Eliminating the shift carrier and associated bushings drastically reduces "slop" and side-to-side play in the shift lever
Increased Precision: Mounting the shifter to the chassis allows for little to no variation in gear selection
Universal Fitment: Fits many BMW chassis with the provided base plate and hardware (see "Fits These Cars" for exact fitment information)
DESIGN

6061 aluminum, 4130 steel, and 316 stainless steel construction
A type-II black anodized finish
Adjustable self-centering spring
"Rally Style" shift lever
Spherical bearing pivot with maintenance-free brass insert
Product Development:

Our Chassis Mount Shifters are designed, engineered, tested and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer and rigorous long term product testing.