Cylinder Head for BMW 3 Series E46 (1999-2005)

ARP Steel Block Head Stud Kit for M50/M52 & S50/S52 (US Spec) ...

T#:3606

Part#: 201-4302

In Stock

19% off MSRP $ 295.92

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 240.99 USD

Add to Wish List

Qty

19% off MSRP

$ 295.92

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 240.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found for the E36 6 cylinder engines, and we highly recommend them in both the racing and forced induction arena. (Due to the additional clamping force between the head and block, these are IDEAL for turbo charging and supercharging!)

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set. Kit includes everything pictured -- 14 head bolts, washers, bolts and assembly lubricant.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These head studs fit the following BMWs/engines (steel block only)
1992-1995 M50 6 cylinder including 325i, 325is and 525i
1996-1999 M52 6 cylinder including 328i, 328is, 323is, 528i
1995-1995 S50US 3.0 liter including 1995 M3 (US only)
1996-1999 S52US 3.2 liter including 1996-1999 M3 (US) and MZ3

Show More Show Less

ARP S54 Head Stud Kit (E46M3 / MZ3 / MZ4)

T#:3631

Part#: 201-4303

In Stock

$ 247.99 USD

Add to Wish List

Qty

$ 247.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs, particularly on the S54 3.2 liter engine. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best S54 head studs we've found for the E46 M3 6 cylinder engines, and we highly recommend them in both the racing and forced induction arena. (Due to the additional clamping force between the head and block, these are IDEAL for turbo charging and supercharging!)

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set. Kit includes everything pictured -- 14 head bolts, washers, bolts and assembly lubricant.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These head studs fit the following BMWs/engines
2001-2006 E46 M3 coupe & convertible
2001-2002 MZ3 M Roadster & M Coupe (with S54 engine)
2006-2008 MZ4 Z4 M Roadster & M Coupe

Show More Show Less

Athena Cut Ring Head Gasket - 84.5mm - BMW M50 M52 (84mm Bore) ...

T#:26171655

Part#: ATH-HG-CR-M50-84

In Stock

$ 324.99 USD

Add to Wish List

Qty

$ 324.99 USD

Add to Wish List

Upgrade your BMW engine's performance with the Athena Cut Ring Head Gasket. This gasket replaces BMW part # 11121726619 and 11121726617 and is specifically designed for M50 & M52 iron block inline 6-cylinder engines found in E34/E36 chassis. Standard OEM & MLS gaskets can only handle a certain amount of cylinder pressure before they start to leak, making the Athena Cut Ring Head Gasket the recommended choice for applications making 16+ psi. A compression leak passing the head gasket can cause a range of issues, including engine overheating, loss of power, misfires, and in severe cases, catastrophic engine failure. Athena's gasket is crafted with premium quality reinforced M0115, an asbestos-free material that's original equipment approved and renowned for its superior quality. The AISI 304 stainless steel Cooper Rings bite into the aluminum head, providing maximum sealing capabilities around the cylinder bore and optimizing engine performance, even on engines with nitrous and/or turbo applications that exceed 2-bar boost. Before installation, it is crucial to have the mating surfaces of the cylinder head and block professionally cleaned and resurfaced to ensure they are completely flat. Please be aware that the gasket should have a size that is 0.5mm to 1mm larger than the piston. For example, if the piston measures 84mm, then the gasket should be the next size up, either 84.5mm or 85mm. Installation instructions: Make sure that the engine block and cylinder head surfaces are clean, flat, and free from any debris, oil, or coolant. Install the Cut Ring gasket on the engine block and ensure that it is properly aligned. Avoid twisting or bending the gasket during installation. Place the cylinder head on top of the gasket and install the head bolts or studs in their correct positions. Follow the manufacturer's recommended torque specifications and tighten the bolts or studs in the proper sequence to ensure even clamping force across the gasket. After the initial tightening, re-torque the head bolts or studs after the engine has been started and then allowed to cool to room temperature. This will ensure that the gasket is properly seated and compressed. It is recommended to not use any additional sealant on the MLS gasket, as it is already coated with a Viton rubber sealant. Using additional sealant can hinder the performance of the gasket.

Show More Show Less

Elring Cylinder Head Bolt Set - E39, E46, E53

2X Entries Into Our F80 M3 Sweepstakes

T#:377047

Part#: 11121740065

In Stock

$ 43.56

This product was last offered at the strikethrough price on
08-12-2026

$ 34.99 USD

Add to Wish List

Qty

$ 34.99 USD

Add to Wish List

Includes all head bolts in one cylinder head

OEM INA Hydraulic Lifter - BMW M5X S5X M62 S62

We Price Match - Give Us A Call or Chat!

T#:360996

Part#: 11321748884

In Stock

$ 19.99 USD

Add to Wish List

Qty

$ 19.99 USD

Add to Wish List

Stock replacement hydraulic valve lifter for the M52, M54 and S50 S52 engines. These lifter buckets can last 150,000+ miles but then they no longer fit on the valve stem correctly and a ticking or knocking noise can result. If the lifter is no longer seated correctly, it can lead to the valve not opening correctly. Replacement is straight-forward but requires special tools for working with the camshafts. This item fits the following BMWs:
1995-1998 E36 BMW 323is 323ic 328i 328is 328ic M3
1997-2003 E39 BMW 525i 528i 530i M5
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2004-2005 E60 BMW 525i 530i
2004-2005 E83 BMW X3 2.5i X3 3.0i
2000-2006 E53 BMW X5 3.0i
1996-2002 E36/7 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i
1998-2000 E36/7 BMW M Roadster M Coupe

Show More Show Less

Project Cars

SELECT YOUR BMW

Cylinder Head for BMW 3 Series E46 (1999-2005)

Sub-Categories

ARP Steel Block Head Stud Kit for M50/M52 & S50/S52 (US Spec) ...

ARP S54 Head Stud Kit (E46M3 / MZ3 / MZ4)

Athena Cut Ring Head Gasket - 84.5mm - BMW M50 M52 (84mm Bore) ...

Elring Cylinder Head Bolt Set - E39, E46, E53

OEM INA Hydraulic Lifter - BMW M5X S5X M62 S62

Select Vehicle

Purpose

Category

Brand

Price

Shipping

Narrow Results